Jonsered GT 2125 Operator's Manual
  1. Manuals
  2. Brands
  3. Jonsered Manuals
  4. Trimmer
  5. GT 2125
  6. Operator's manual

Jonsered GT 2125 Operator's Manual

Jonsered operator's manual
Hide thumbs Also See for GT 2125:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual
Operator's manual (EPA)
Please read the operator's manual
carefully and make sure you
understand the instructions before
using the machine.
GT 2125 GC 2125

Advertisement

Table of Contents
loading

Related Manuals for Jonsered GT 2125

Summary of Contents for Jonsered GT 2125

  • Page 1 Operator’s manual (EPA) Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. GT 2125 GC 2125...

  • Page 2: Key To Symbols

    Arrows which show limits for handle positioning. Always wear approved protective gloves. Wear sturdy, non-slip boots. Only use non-metallic, flexible cutting attachments, i.e. trimmer heads with trimmer cord. 2 – English KEY TO SYMBOLS Only intended for trimmer heads.

  • Page 3: Table Of Contents

    YOUR WARRANTY RIGHTS AND OBLIGATIONS ... CONTENTS Note the following before starting: Jonsered has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hearing impairment.

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective equipment IMPORTANT! You must use approved personal protective equipment whenever you use the machine. Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an accident does happen. Ask your dealer for help in choosing the right equipment.

  • Page 5: Cutting Equipment

    fire. Never start the machine indoors or near combustible material! Cutting equipment Grass blades and grass cutters are intended for cutting coarse grass. A trimmer head is intended for trimming grass. Locking nut A locking nut is used to secure some types of cutting attachment. – 5...

  • Page 6: Checking, Maintaining And Servicing The Machine ' S Safety Equipment

    SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine ′ ′ ′ ′ s safety equipment IMPORTANT! All servicing and repair work on the machine requires special training. This is especially true of the machine ′ s safety equipment. If your machine fails any of the checks described below you must contact your service agent.
  • Page 7 SAFETY INSTRUCTIONS • Regularly check that the muffler is securely attached to the machine. • If the muffler on your machine is fitted with a spark arrestor mesh then it should be cleaned regularly. A blocked mesh causes the engine to overheat, which can lead to serious damage.

  • Page 8: Cutting Equipment

    • Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days.

  • Page 9: General Safety Precautions

    SAFETY INSTRUCTIONS General safety precautions IMPORTANT! The machine is only designed for trimming grass, grass clearing and/or forestry clearing. The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data. Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination.

  • Page 10: General Working Instructions

    • Use a grass cutter or grass blade for clearing grass. • Use a trimmer head or plastic blades for lighter clearing work, for example along verges or around trees. WARNING! Sometimes branches or grass get caught between the guard and cutting attachment.
  • Page 11 Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. CAUTION! This technique increases the wear on the cord.

  • Page 12: What Is What

    What is what on the trimmer? 1 Trimmer head 2 Grease filler cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lock 10 Cylinder cover 11 Starter handle...

  • Page 13: Assembly

    • Slide the spacer into the slot in the loop handle. • Fit the nut, washer and screw. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob. Fitting the J-handle (GC 2125) • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft.

  • Page 14: Fitting The Trimmer Guard And Auto 32 Trimmer Head

    (Caution! left-hand thread). • Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.

  • Page 15: Fitting Other Guards And Cutting Attachments

    Fitting other guards and cutting attachments (GC 2125) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (L). • Fit the drive disc (B) on the output shaft.

  • Page 16: Fuel Handling

    16 – English FUEL HANDLING Two-stroke oil • For the best results and performance use JONSERED two-stroke oil, which is specially formulated for our two- stroke engines. Mixture 1:50 (2%). • Never use two-stroke oil intended for water-cooled outboard engines, sometimes referred to as outboard oil.

  • Page 17: Fueling

    Fueling WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke or place hot objects near fuel. Always shut off the engine before refuelling. Always stop the engine and let it cool for a few minutes before refuelling. When refuelling, open the fuel cap slowly so that any excess pressure is released gently.

  • Page 18: Starting And Stopping

    • Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. • Never use the machine without a guard nor with a defective guard.
  • Page 19 STARTING AND STOPPING some resistance (the starter pawls grip), now quickly and powerfully pull the cord. Never wrap the starter cord around your hand Repeat pulling the cord until the engine starts. When the engine starts. return choke control to run position and apply full throttle;...

  • Page 20: Maintenance

    Carburetor Your Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. To ensure that the engine runs at peak performance and...

  • Page 21: Muffler

    Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops.

  • Page 22: Cooling System

    However, before using the machine you should check that the bevel gear is filled 3/4 full with grease. Use JONSERED special grease. The grease in the bevel gear does not normally need to be changed except if repairs are carried out.

  • Page 23: Spark Plug

    • Check that the blade is properly centered, sharp and without cracks. • Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. • A non-balanced blade/trimmer head induces heavy vibrations that may damage the machine.

  • Page 24: Technical Data Technical Data

    NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. 24 – English TECHNICAL DATA GT 2125 GC 2125 1,50/24,5 1,50/24,5 1,28/32...
  • Page 25 Approved accessories GT 2125 Blade shaft thread 3/8 R Trimmer head GC 2125 Arbor shaft thread M10 Trimmer head Grass blade/grass cutter Plastic blades WARNING! Grass blades or grass knives may only be used when the J-handle is fitted. See instructions under the heading Assembling the J-handle.

  • Page 26: Federal Emission Control Warranty Statement

    Operator′s Manual. Jonsered recommends that you retain all receipts covering maintenance on your small nonroad engine, but Jonsered cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the small nonroad engine owner,...
  • Page 27 Trimmy H II 15 cm 6" 7,5 m ~ 3,7 m 15 cm 6"...
  • Page 28 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
  • Page 29 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
  • Page 30 Tap-N-Go 35 15 cm 6" ´®z*x}3¶5U¨ ´®z*x}3¶5U¨ 8,5 m 10 cm 4" 4,3 m "Clic"...
  • Page 31 Auto 32 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...
  • Page 32 1088931-95 ´®z*x}3¶5U¨ ´®z*x}3¶5U¨ 2004-06-14...

This manual is also suitable for:

Gc2125

Table of Contents