Husqvarna 555 Operator's Manual page 39

Engine
Cylinder displacement, cu.in/cm
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/hp @ rpm
Emissions Durability Period according to California Air
Resources Board, h.
Ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication system
Fuel tank capacity, US pint/litre
Oil pump capacity at 9,000 rpm, ml/min
Oil tank capacity, US pint/litre
Type of oil pump
Weight
Chain saw without bar or chain, empty tanks, lb/kg
Chain/bar
Guide bar-mount
Standard bar length, inch/cm
Recommended bar lengths, inch/cm
Usable cutting length, inches/cm
Pitch, inch/mm
Thickness of drive links, inch/mm
Drive sprocket type/teeth
Chain speed at 133% of maximum engine power
speed, ft/s / m/s.
Recommended cutting equipment for USA
Following is a list of recommended cutting equipment for the Husqvarna chain saw models 555, 556, 560XP, 560XPG,
562XP and 562XPG. The combinations of powerhead, guide bar and saw chain have been investigated in accordance
with the kickback and vibration requirements of ANSI B175.1–2012.
The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the
corresponding maximum nose radius of a solid bar. The following list is the chain saw manufacturers recommendations.
There may be other combinations available, which will also achieve kickback reduction. As we are listing the maximum
guide bar nose radius, you may use a guide bar with smaller nose radius than in our list. For guide bars of the same
length, all sprocket-nose guide bars of the same pitch and having the same number of sprocket teeth may be considered
to have equivalent kickback energy. A hard nose bar having the same length and nose radius as a sprocket-nose bar
may be considered to have equivalent or less kickback energy than the sprocket-nose bar.
"Low kickback saw chain" is a saw chain which has only met the kickback performance requirements of ANSI B175.1-
2012 safety requirements for gasoline powered chain saws when tested on the representative sample of chain saws
below 3.8 cu. in. specified in ANSI B175.1-2012. We recommend that you as a replacement use the listed saw chains
or "Low kickback saw chains" which are available at your dealer.
TECHNICAL DATA
3
560XPG 562XP
3,65/59,8 3,65/59,8
1,81/46 1,81/46
1,42/36 1,42/36
2800 2800
3,5/4,8 @ 9600 3,5/4,8 @ 9600
300 300
NGK CMR6H NGK CMR6H
0.02/0,5 0.02/0,5
1.37/0,65 1.37/0,65
6-15 6-15
0,74/0,35 0,74/0,35
Adjustable Adjustable
13.0/5,9 13.0/5,9
Small Large
18/46 20"/51
13-24"/33-61 16-28"/41-71
12-23"/31-58 15-27"/38-69
0.325/8,25 3/8" /9,52
0.050/1,3 0.050/1,3
0.058/1,5 0.058/1,5
Rim/7 Rim/7
92.8 / 28.3 92.8 / 28.3
562XPG
3,65/59,8
1,81/46
1,42/36
2800
3,5/4,8 @ 9600
300
NGK CMR6H
0.02/0,5
1.37/0,65
6-15
0,74/0,35
Adjustable
13,5/6,1
Large
20"/51
16-28"/41-71
15-27"/38-69
3/8" /9,52
0.050/1,3
0.058/1,5
Rim/7
92.8 / 28.3
English – 39