Whirlpool 27" Installation Instructions Manual
27" (69 cm) electric washer/dryer
Hide thumbs
Also See for 27":
- Job aid (36 pages) ,
- Installation instructions manual (12 pages) ,
- Installation instructions (5 pages)
Table of Contents
Advertisement
Quick Links
27" (69 CM) ELECTRIC WASHER/DRYER
INSTRUCTIONS POUR L'INSTALLATION DE LA LAVEUSE/
SÉCHEUSE ÉLECTRIQUE DE 27" (69 CM)
Table of Contents
WASHER/DRYER SAFETY .......................................................... 1
INSTALLATION REQUIREMENTS ............................................... 3
Tools and Parts ..................................................................... 3
LOCATION REQUIREMENTS ...................................................... 5
DIMENSIONS/CLEARANCES ..................................................... 6
DRAIN SYSTEM ........................................................................... 7
ELECTRICAL REQUIREMENTS - U.S.A..................................... 8
ELECTRICAL REQUIREMENTS - CANADA ............................... 9
REMOVE SHIPPING STRAP ...................................................... 10
INSTALL LEVELING LEGS ......................................................... 10
ELECTRICAL CONNECTION (U.S.A. ONLY) ............................ 11
VENTING ..................................................................................... 17
Venting Requirements ........................................................ 17
Plan Vent System ................................................................ 18
Install Vent System ............................................................. 19
CONNECT DRAIN HOSE ........................................................... 20
CONNECT INLET HOSES .......................................................... 21
CONNECT VENT ........................................................................ 22
LEVEL WASHER/DRYER ........................................................... 23
COMPLETE INSTALLATION CHECKLIST ................................ 24
INSTALLATION NOTES
Date of purchase: _________________________________________
Date of installation: _______________________________________
Installer: _________________________________________________
Model number: ___________________________________________
Serial number: ____________________________________________
WASHER/DRYER SAFETY
W10356098C
INSTALLATION INSTRUCTIONS
Table des matières
SÉCURITÉ DE LA LAVEUSE/SÉCHEUSE ................................ 25
EXIGENCES D'INSTALLATION ................................................. 27
Outillage et pièces ............................................................. 27
EXIGENCES D'EMPLACEMENT .............................................. 29
DIMENSIONS/DISTANCES DE DÉGAGEMENT ....................... 30
SYSTÈME DE VIDANGE ............................................................ 31
SPÉCIFICATIONS ÉLECTRIQUES - CANADA ......................... 32
ENLEVER LA SANGLE D'EXPÉDITION .................................... 33
INSTALLATION DES PIEDS DE NIVELLEMENT ...................... 33
ÉVACUATION ............................................................................. 34
Exigences concernant l'évacuation ................................. 34
Planification du système d'évacuation ............................ 35
Installation du conduit d'évacuation ................................ 36
RACCORDEMENT DU TUYAU DE VIDANGE ........................... 37
RACCORDEMENT DES TUYAUX D'ARRIVÉE D'EAU ............. 38
RACCORDEMENT DU CONDUIT D'ÉVACUATION ................. 39
ÉTABLISSEMENT DE L'APLOMB DE
LA LAVEUSE/SÉCHEUSE .......................................................... 40
LISTE DE VÉRIFICATION POUR L'ACHÈVEMENT
DE L'INSTALLATION .................................................................. 41
NOTES CONCERNANT L'INSTALLATION
Date d'achat : ____________________________________________
Date d'installation : _______________________________________
Installateur : ______________________________________________
Numéro de modèle : ______________________________________
Numéro de série : _________________________________________
Advertisement
Table of Contents
Related Manuals for Whirlpool 27"
Summary of Contents for Whirlpool 27"
-
Page 1: Table Of Contents
27" (69 CM) ELECTRIC WASHER/DRYER INSTALLATION INSTRUCTIONS INSTRUCTIONS POUR L’INSTALLATION DE LA LAVEUSE/ SÉCHEUSE ÉLECTRIQUE DE 27" (69 CM) Table of Contents Table des matières WASHER/DRYER SAFETY ............1 SÉCURITÉ DE LA LAVEUSE/SÉCHEUSE ........ 25 INSTALLATION REQUIREMENTS ..........3 EXIGENCES D’INSTALLATION ..........27 Tools and Parts .............. - Page 2 WASHER/DRYER SAFETY...
-
Page 3: Installation Requirements
INSTALLATION REQUIREMENTS TOOLS AND PARTS Gather required tools and parts before starting installation. Tools needed: Optional tools: Flat-blade screwdriver #2 Phillips screwdriver Flashlight Bucket Parts supplied: NOTE: Remove parts package from the washer basket. Check that all parts were included. Adjustable or open-end Level wrench 9/16"... - Page 4 INSTALLATION REQUIREMENTS TOOLS AND PARTS Parts needed: Alternate parts: (Not supplied with washer/dryer) (Not supplied with washer/dryer) Your installation may require additional parts. To order, please Vent clamps refer to toll-free numbers on back page of your Use and Care Vent elbows and ductwork Guide.
-
Page 5: Location Requirements
LOCATION REQUIREMENTS Recessed area or closet installation 48 in. (310 cm 3" (76 mm) Front Closet View door Select proper location for your washer to improve performance and minimize noise and possible “washer walk.” Install your 3" (76 mm) washer in a basement, laundry room, closet, or recessed area. 24 in. -
Page 6: Dimensions/Clearances
DIMENSIONS/CLEARANCES Dimensions Clearances Front View Side Clearances (recommended/minimum) " (692 mm) " (1822 mm) 1"/0" 1"/0" 1" (25 mm/0 mm) (25 mm/0 mm) (25 mm) Side View " (1213 mm) 26" Front/Back/Top Clearances (660 mm) 12" (305 mm) " " (1670 mm) (1822 mm) "... -
Page 7: Drain System
DRAIN SYSTEM Floor drain system Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need. Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285385), and an Floor standpipe drain system Extension Drain Hose (Part Number 285863) that may be purchased separately. -
Page 8: Electrical Requirements - U.s.a
ELECTRICAL REQUIREMENTS – U.S.A. This washer/dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground wire is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground wire must be removed from the internal ground connector (green screw), and secured under the neutral terminal (center or white wire) of the... -
Page 9: Electrical Requirements - Canada
ELECTRICAL REQUIREMENTS – U.S.A. ELECTRICAL REQUIREMENTS – CANADA It is your responsibility: To contact a qualified electrical installer. To be sure that the electrical connection is adequate and in conformance with Canadian Electrical Code, C22.1 – latest edition and all local codes. A copy of above codes standard may be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA. -
Page 10: Remove Shipping Strap
REMOVE SHIPPING STRAP INSTALL LEVELING LEGS To avoid floor damage, set washer/dryer onto cardboard before moving across floor. Move washer/dryer close to its final location. Prepare to install leveling feet Remove strap, hang tag, and pin 1" (25 mm) Prop up the front of the washer/dryer Do not cut yellow strap. -
Page 11: Electrical Connection (U.s.a. Only)
ELECTRICAL CONNECTION (U.S.A. ONLY) Power Supply Cord Direct Wire Electrical Connection Options Remove terminal block cover Choose electrical connection type Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to “4-wire Power Supply Cord Connection” section. Then, go to “Venting Requirements.” Power supply cord 3-wire receptacle (NEMA Type 10-30R): Go to “3-wire Power Supply Cord Connection”... - Page 12 Power Supply Cord Connection Power Supply Cord Strain Relief 4-Wire Power Supply Cord Connection Attach power supply cord strain IMPORTANT: A 4-wire connection is required for mobile relief homes and where local codes do not permit the use of 3-wire connections.
- Page 13 Connect ground wire Remove center screw Remove center terminal block screw (B). Connect ground wire (F) (green or bare) of power supply cord Connect neutral wire to external ground conductor screw (A). Tighten screw. Connect remaining wires Connect neutral wire (white or center) (C) of power supply cord to center terminal block screw (B).
- Page 14 Direct Wire Connection Direct Wire Strain Relief 4-Wire Direct Wire Connection IMPORTANT: A 4-wire connection is required for mobile Attach direct wire strain relief homes and where local codes do not permit 3-wire connections. Prepare your 4-wire cable for direct connection Unscrew the removable conduit connector (A) and any screws from a 3/4"...
- Page 15 3-Wire Direct Wire Connection Connect neutral ground wire IMPORTANT: Use where local codes permit connecting and neutral wire cabinet-ground conductor to neutral wire. Prepare your 3-wire cable for direct connection Connect neutral ground wire (E) and place hooked end (hook facing right) of neutral Direct wire cable must have 5 ft.
- Page 16 Connect neutral ground wire Connect neutral wire and neutral wire Place hooked end of neutral wire (white or center) (C) of direct wire cable under center Connect neutral ground wire (E) and neutral wire (white or terminal block screw (B). Squeeze hooked center wire) (C) of power supply cord or cable under center end together.
-
Page 17: Venting
VENTING Venting Requirements Exhaust hoods: Must be at least 12" (305 mm) from ground or any object that may obstruct exhaust (such as flowers, rocks, bushes, or snow). Recommended Styles: Louvered hood Box hood Acceptable Style: WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS. -
Page 18: Plan Vent System
VENTING Plan Vent System Alternate installations for close clearances Venting systems come in many varieties. Select the type best Recommended exhaust installations for your installation. Three close-clearance installations are Typical installations vent the washer/dryer from the rear. Other shown. Refer to the manufacturer’s instructions. installations are possible. -
Page 19: Install Vent System
Install Vent System Special provisions for mobile home installations: The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside. Install exhaust hood 12"... -
Page 20: Connect Drain Hose
CONNECT DRAIN HOSE Proper connection of the drain hose protects your floors from damage due to water leakage. To keep the drain hose from Place drain hose in standpipe coming off or leaking, it must be installed according to the following instructions: Drain hose form... -
Page 21: Connect Inlet Hoses
CONNECT INLET HOSES Washer must be connected to water faucets with new inlet hoses with flat washers (not provided). Do not use old hoses. Clear water lines NOTE: Both hoses must be attached and have water flowing to inlet valves. If you are only connecting to a cold water faucet, you must use a Y-adapter (not included). -
Page 22: Connect Vent
CONNECT INLET HOSES CONNECT VENT Check for leaks Connect vent to exhaust outlet Connecting from front Connecting (for closet or recessed from rear area) Using a 4" (102 mm) clamp, connect vent to exhaust outlet Turn on water faucets to check for leaks. A small amount of in dryer. -
Page 23: Level Washer/Dryer
LEVEL WASHER/DRYER IMPORTANT: Level washer/dryer properly to reduce excess noise and vibration. Tighten leveling feet Check levelness of washer/dryer Jam nut Place level here Place level here When washer/dryer is level, use a 9/16" or 14 mm open-end or adjustable wrench to turn jam nuts counterclockwise on With washer/dryer in its final location, place a level on top leveling feet tightly against washer/dryer cabinet. -
Page 24: Complete Installation Checklist
LEVEL WASHER/DRYER COMPLETE INSTALLATION CHECKLIST In Canada Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. Check that you have all of your tools. Dispose of/recycle all packaging materials. Keep the plastic foam for use if the washer/dryer should be transported. -
Page 25: Sécurité De La Laveuse/Sécheuse
NOTES... - Page 26 NOTES...
-
Page 27: Exigences D'installation
05/13 ®/ © 2013 Whirlpool. All rights reserved. Used under license in Canada. Printed in U.S.A. W10356098C ®/ © 2013 Whirlpool. Tous droits réservés. Emploi sous licence au Canada. Imprimé aux É.-U.