Page 4
Contents . Wiring Diagram …………………………………………………………………………………………………………………………………8 9. S chematic Diagrams ……………………………………………………………………………………………………………………………9 9-1 Schematic Diagrams ……………………………………………………………………………………………………………………… 9-1 9-2 Schematic Diagrams ………………………………………………………………………………………………………………………9-3 1 1 0. Operating Instructions and Installation … … …………………………………………………………………………………………………10-1 10-1 Front …………………………………………………………………………………………………………………………………… 10-1 10-2 Rear ………………………………………………………………………………………………………………………………………10-2 10-3 Using the Stand …………………………………………………………………………………………………………………………10-4 1 1 1.
Page 5
Samsung Electronics Co.,Ltd. -This Service Manual is a property of Samsung 416, Maetan-3Dong, Yeongtong-Gu, Suwon City, Electronics Co., Ltd. Gyeonggi-Do, Korea, 443-742 Any unauthorized use of Manual can be punished Printed in Korea under applicable International and/or domestic P/N : BN82-00138M-03 law.
1 Precautions 1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1 Precautions 1-4 Installation Precautions 1. For safety reasons, more than two people are 6. Keep the antenna far away from any high-voltage required for carrying the product. cables and install it firmly. Contact with the highvoltage cable or the antenna falling over may 2.
14 Reference Infomation 14 Reference Infomation 14-1 Technical Terms - TFT-LCD - FINE "Fine" adjustment is used to adjust visibility by (Thin film Transistor Liquid Crystal Display) ADC(Analog to Digital Converter) control phase difference. This is a circuit that converts from analog signal to digital signals.
Page 17
14 Reference Infomation - Dot Pitch - External Device Input The image on a monitor is composed of red, green External device input refers to video input from and blue dots. The closer the dots, the higher the such external video devices as VCRs, camcorders resolution.
14 Reference Infomation - Connecting the Monitor Connect the DC adapter for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
14 Reference Infomation 14-2 Pin Assignments Sync 15-Pin D-Sub Signal Cable Connector Type Separate Composite Sync-on-green Pin No. Green Green Green + H/V Sync. Blue Blue Blue DDC Return (GND) DDC Return (GND) DDC Return (GND) GND-R GND-R GND-R GND-G GND-G GND-G GND-B...
14 Reference Infomation 14-3 Timing Chart - This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 14-1 Timing Chart VESA Mode VGA2/ VGA3/ 640/75 Hz 800/60 Hz 800/75 Hz 1024/60 Hz 1024/75 Hz 1280/60 Hz...
14 Reference Infomation 14-4 Preset Timing Modes - If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on.
2 Product Specifications 2 Product Specifications 2-1 Fashion Feature -. Magic Rotation application(Auto pivot Delete) -. Embeded Power, Mechanical S/W application 2-2 Feature Feature Feature Operating method If Monitor turns on in some resolution for the first time, it can execute Auto Auto Auto adjustment automatically for the high Quality Auto Power...
5 Exploded View & Parts List 5 Exploded View and Parts List -You can search for updated part codes through ITSELF web site. URL : http://itself. sec. samsung.co.kr 5-1 LS22MEHSFV/XSF Exploded View T0003 M0215 M0006 M0013 M0014 M0112 M0174 M0006...
8 Wiring Diagram 8 Wiring Diagram Connected to the I/P board Connected to the Panel through the LVDS cable For test(not used) For DVI signal For function key For Analog signal...