Table of Contents
Advertisement
•
The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
•
For best cutting performance, grass over 6 inches
in height should be mowed twice. Make the fi rst cut
relatively high; the second to desired height.
TO ADJUST GAUGE WHEELS (See Fig. 7)
Gauge wheels are properly adjusted when they are slightly
off the ground when mower is at the desired cutting height
in operating position. Gauge wheels then keep the deck
in proper position to help prevent scalping in most terrain
conditions.
NOTE: Be sure tractor is on a fl at level surface.
•
Lower mower and adjust mower to desired cutting
height(See "TO AD JUST MOWER CUT TING HEIGHT"
in this sec tion of manual).
•
Remove retainer spring and clevis pin which secure
each gauge wheel bar.
•
Lower gauge wheels to ground. Raise gauge wheels
slightly to align holes in bracket and gauge wheel bar
and insert clevis pin. Gauge wheels should be slightly
off the ground.
•
Replace retainer spring into clevis pin.
•
Be sure all gauge wheels are in the same setting.
IMPORTANT:
BE
SURE
WHEELS IF YOU CHANGE THE CUTTING HEIGHT
OF THE MOWER DECK.
RETAINER
SPRING
TO OPERATE MOWER (See Fig. 8)
Your tractor is equipped with an operator presence sensing
switch. Any attempt by the operator to leave the seat with
the engine running and the attachment clutch engaged
will shut off the engine. You must remain fully and centrally
positioned in the seat to prevent the engine from hesitating
or cutting off when operating your equipment on rough,
rolling terrain or hills.
•
Select desired height of cut.
•
Lower mower with attachment lift control.
•
Start mower blades by engaging attachment clutch
control.
•
TO STOP MOWER BLADES - disengage attachment
clutch con trol.
CAUTION: Do not operate the mower
without either the en tire grass catcher,
on mowers so equipped, or the defl ector
shield in place.
OPERATION
TO
READJUST
GAUGE
CLEVIS
PIN
FIG. 7
AT TACH MENT
CLUTCH
ENGAGED
POSITION
DISENGAGED
POSITION"
REVERSE OPERATION SYSTEM (ROS)
Your tractor is equipped with a Reverse Operation System
(ROS). Any attempt by the operator to travel in the reverse direc-
tion with the attachment clutch engaged will shut off the engine
unless ignition key is placed in the ROS "ON" position.
WARNING: Backing up with the attachment clutch en-
gaged while mowing is strongly discouraged. Turning the
ROS "ON", to allow reverse operation with the attachment
clutch engaged, should only be done when the operator
decides it is necessary to reposition the machine with the
attachment engaged. Do not mow in reverse unless
absolutely necessary.
USING THE REVERSE OPERATION SYSTEM -
•
Move motion control lever to neutral (N) position.
•
With engine running, turn ignition key counterclockwise
to ROS "ON" position.
•
Look down and behind before backing.
•
Slowly move motion control lever to reverse (R) po si tion
to start movement.
•
When use of the ROS is no longer needed, turn the
ignition key clockwise to engine "ON" position.
ROS "ON" POSITION
TO OPERATE ON HILLS
CAUTION: Do not drive up or down hills
with slopes greater than 15° and do not
drive across any slope.
•
Choose the slowest speed before starting up or down
hills.
•
Avoid stopping or changing speed on hills.
•
If stopping is absolutely necessary, push brake pedal
quickly to brake position and engage parking brake.
•
To restart movement, slowly release parking brake and
brake pedal.
•
Slowly depress appropriate drive pedal to slowest set-
ting.
•
Make all turns slowly.
12
AT TACH MENT
LIFT LEVER
HIGH PO SI TION
LOW
POSITION
DE FLEC TOR
SHIELD
FIG. 8
ENGINE "ON" POSITION
(NORMAL OPERATING)
Advertisement
Table of Contents
