Setting Contrast Mode - Cobra 29 LX BT CB Operating Instructions Manual

Operation
Setting
Contrast Mode
Note
If an attempt is made to
exceed the highest or lowest
contrast levels, 1 error beep
will be heard.
Bluetooth
®
Note
When cell phone calls are in
progress using the Bluetooth
features, the CB functions of the
2 3
1.5
NB/ANL CAL
SWR
TX
unit are disabled.
ANL
RX
S/RF
RF
SWR
Note
CAL
3 5 7 9
1
Dual Point Bluetooth:
SIG +30dB
Two cell phones can be paired
OL and and used for team drivers. SQ DYNAMIKE
Note
If no further pairing steps are
taken, the unit will time-out
MIN
and return to Standby after
five minutes. During the pair-
ing process, press and
release the BT Button to can-
cel the pairing process.
Note
For Text-to-Speech conversion,
an app should be downloaded
to your cell phone.
22

Setting Contrast Mode

Press Menu/Enter knob and rotate clockwise to
select Set Contrast. Press Menu/Enter knob
again and rotate clockwise to increase contrast,
counter-clockwise to decrease contrast.
Press Menu/Enter knob to set contrast.
TURN CH KNOB TO
SET CONTRAST
Press Menu/Enter knob again to exit routine.
Bluetooth®
Calls on a Bluetooth enabled cell phone can be
routed through the 29 LX BT speaker or external
speaker accessory.
READY FOR
PAIRING
PW 0000
MEM WX !
BT Button
RF GAIN DELTA TUNE
To Pair with a Cell Phone
With 29 LX BT power On, press and hold the BT
MIN MAX
Button for six seconds to enter Standby mode. A
tone will sound to confirm entry to Standby.
A. First time pairing with a cell phone:
I. A tone will sound to confirm Pairing mode.
II. Follow the cell phone manufacturer's
instruction to enable its Bluetooth
function and enter the PIN (Personal
Identification Number) 0000.
III. Successful pairing will be indicated by
a tone to confirm entry to Connected
mode. A pair record will also be established
for subsequent connections.
B. Subsequent pairings with a cell phone:
I. Follow any cell phone manufacturer
instructions if needed, to enable the
Bluetooth function.
II. Successful pairing will be indicated by a
tone to confirm entry to Connected mode.
To Answer Calls
Press and release the BT Button when the cell
1
phone ring is heard through the 29 LX BT speaker.
Speak into the 29 LX BT microphone. The CB
2
function of the unit and PTT Button will be
disabled while a call is in progress.
Press and release of the BT Button to end the
3
CH 9/
SCAN
19
call. A tone will sound.
MEM SCAN
To Initiate Calls
1 Dial a number according to the cell phone manu-
ESC facturer's instructions. The key press and other
tones will be heard through the 29 LX BT speaker.
SWR
Press Send on the cell phone send key a few
T BACK
2
CAL
seconds, you will hear the ring tone for the
number you dialed on the CB speaker.
Once connected, speak into the microphone.
3 Press and release of the BT Button to end the
OFF
call. A tone will sound.
4
Press and hold the BT Button for two seconds to
redial a number. A tone will sound; and after a
5
few seconds, you will hear the ring tone for the
number you dialed.
To Enable or Disable Voice Dialing
If the paired cell phone supports voice dialing,
press and release the BT Button twice to toggle
between enabling and disabling this feature.
Operation
Note
When cell phone calls are in
progress using the Bluetooth
features, the CB functions of
the unit are disabled until the
phone call is put on hold (see
page 24).
Note
The external microphone (see
accessories on page 35) can be
plugged into the rear of the
unit and clipped to a pocket or
lapel for hands-free speech dur-
ing calls.
When the microphone is
plugged in, the main micro-
phone will not pick up speech
during calls but will be fully
functional for CB operation.
23