Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NEO ProLink PVL13V9
Summary of Contents for NEO ProLink PVL13V9
-
Page 2: Chapter 1 - Getting Started
Installation and operation instructions Chapter 1 – Getting Started 1.1 Subject The Neo ProLink V9 adapter—an integration that links between an iPod (and iPhone) and a car stereo. The ProLink adapter features are: iPod/iPhone© play, charge and control via EXT2 port. •... -
Page 3: Important Compatibility Notes
The Neo Car Audio adapter set consists of the 3V9 interface, one iPod dock cable, and one vehicle-specific cable with optional accessories. NEO ProLink 3v9 Interface (1) Docking cable (2) Vehicle specific cable (3) Figure 1. Package contents b) The basic package does not include the optional accessories that you can purchase separately: BLUBTDV9 6FT 3.5mm phone jack cable with USB charging v9-AUXUSB... -
Page 4: Tools Needed
6. For AUDI vehicles only: For some AUDI headunits an additional part or harness modification is required in order to gain the access to the CD changer port. The 8-pin CD changer port on such stereos is occupied by a solid 20-pin connector. Please contact NEO Car Audio to get a special harness to retain factory connections 7. - Page 5 In some Toyota/Lexus/Scion and Honda/Acura vehicles the CD changer port is occupied with a factory harness (such as NAV or audio harness). The NEO package for Toyota/Lexus or Honda/Acura includes a Y shaped vehicle cable. In order to connect the interfaces properly please follow to the scheme below. If the car has no NAV or XM leave the female end of the Toyota or Honda (HON1) harness open.
- Page 6 Chapter 2.2. - Volvo 01-06 using VOL01 harness and Posi-Taps Picture 1: VOL01 vehicle specific harness Preparation It is recommended to disconnect the car battery before performing the installation. Turn off the car engine and remove the key from the ignition. Carefully remove the radio from the dash.
- Page 7 Locate the yellow wire marked as 12V on the VOL01 harness (picture1). Using blue colored Posi-Tap clip provided with your package, connect the constant POWER wire that comes from the main stereo harness (picture 2) to the yellow 12V wire on your VOL01 harness.
- Page 8 If you have any problems with using Posi-Taps please contact Neo Car Audio tech support at 619- 704-0690. Locate black ground wire on VOL01 harness, secure wire to radio / chassis ground. Find a safe accessible place to secure the module.
- Page 9 Fast Forward When pressed, the iPod will start moving quickly through the current track. Fast Reverse When pressed, the iPod will start rewinding the current track. Play/Pause When the stereo is turned to the CD changer mode, the iPod will automatically start playing. Turning the stereo off or switching to another source (FM, AM, etc.) will cause the iPod to pause the current track.
- Page 10 3.7 Using EXT1 for AUX-IN on your NEO 3V9 adapter You can connect any alternative audio sources such as MP3 player, DVD, GPS, XM and etc. to the Neo Car Audio adapter via Mini Din to RCA and 3.5mm phone jack cable (must be purchased separately, is not included in the basic package).
-
Page 11: Troubleshooting
3.9 Troubleshooting Symptom Cause Remedy No power Bad connection Check connections. Make sure unit has good ground. Insure all cables are connected securely with no bent pins. Radio is not recognizing Some car stereos have to be restarted before After connecting the adapter turn the ignition iPod interface the radio recognizes the signal off and back on. -
Page 12: One Year Limited Warranty
All parts of this NEO CAR AUDIO product are guaranteed for a period of 1 year as follows: Within the first 12 months from date of purchase, subject to the conditions above, NEO CAR AUDIO will repair or replace the product if it is defective in material or workmanship providing it is returned to NEO CAR AUDIO, with PROOF OF PURCHASE from an authorized dealer.