Related Manuals for Ryobi RBCGM25SS
Summary of Contents for Ryobi RBCGM25SS
- Page 1 RBCGM25SS TRIMMER / BRUSHCUTTER OPERATOR’S MANUAL (Original Instructions) Important! It is essential you read the instructions in this manual before starting and operating this machine. Subject to technical modifications.
-
Page 4: General Safety Warnings
English (Original Instructions) GENERAL SAFETY WARNINGS „ Dangerous Environments. To avoid falling, do not use the product in damp or wet locations. „ Controlling Product. During carburetor WARNING adjustments the cutting attachment may spin. Read and understand all instructions. Failure to Therefore, you should wear protective equipment follow all instructions may result in serious personal and observe all safety instructions when adjusting... - Page 5 English (Original Instructions) SYMBOLS The following symbols are located on labels on the attachment shaft. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Safety Alert Precautions that involve your safety.
-
Page 6: Specifications
English (Original Instructions) SPECIFICATIONS 4. Guide recess 5. Front handle Weight without fuel 14. Grass deflector 5.31 Kg and trimmer head 23. Trimmer line 24. Trimmer head Weight without fuel 5.61 Kg with trimmer head FIGURE 2 5. Front handle Fuel tank volume 620 cm 6. - Page 7 English (Original Instructions) ASSEMBLY INSTALLING THE REEL EASY LINE TRIMMER HEAD (FIG. 10) ATTACHING THE POWER HEAD TO THE TRIMMER ATTACHMENT (FIG. 1) „ Stop the engine and disconnect the spark plug wire. „ Follow these steps to connect the attachment to the „...
-
Page 8: Operation
English (Original Instructions) „ Wind the line until approximately 20cm remains CONVERTING FROM BRUSH CUTTER TO LINE protruding from the line trimmer head. TRIMMER (FIG. 15) „ Replace the spark plug boot. REMOVING THE BLADE CONVERTING FROM LINE TRIMMER TO BRUSH „... -
Page 9: Filling The Tank
English (Original Instructions) FILLING THE TANK 6. Pull the starter grip (item 19) with a quick firm and consistent upward motion (No more than 4x). „ Clean surface around fuel prevent 7. Set the choke lever to position B (Choke Open). contamination. -
Page 10: Cleaning The Air Filter
English (Original Instructions) few seconds before retapping the bump knob. Do not WARNING allow the line to wear too short. Keep the cutting line Always wear safety goggles or safety glasses with side at full length. shields during tool operation. If operation is dusty, also OPERATING AS A BRUSHCUTTER (FIG. -
Page 11: Checking The Fuel Cap
English (Original Instructions) NOTE: Make sure the filter is seated properly inside the „ Run the engine until it stops. cover. Installing the filter incorrectly will allow dirt to enter „ Clean all foreign material from the product. the engine, causing rapid engine wear. „... -
Page 12: Troubleshooting
English (Original Instructions) TROUBLE SHOOTING PROBLEM POSSIBLE CAUSE SOLUTION 1. Switch set to the O (OFF) position. 1. Set switch to the I (ON) position. 2. No spark 2. Remove the spark plug. Reattach the spark plug cap and lay the spark plug on the metal cylinder. Pull the starter cord and watch for a spark at the spark plug tip. - Page 13 FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES. OUR MAXIMUM LIABILITY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID BY YOU FOR THE PRODUCT. This warranty is applicable only in the European Union, Australia, and New Zealand. Outside these areas, please contact your authorised Ryobi dealer to determine if another warranty applies.
- Page 14 Marlow, Bucks Building B, Rosehill Industrial Estate, SL7 1TB - United Kingdom 3 Shirley Street, Rosehill NSW 2142 RYOBI TECHNOLOGIES (UK) LIMITED Australia Medina House, Fieldhouse Lane, Tel: (02) 8892 1800 or 1300 361 505 Marlow, Bucks Fax: 1800 807 993...