Troubleshooting; Location And Function Of Controls - Akai ACA-3628UC Instruction Manual

TROUBLE SHOOTING
Before using the check list please make all the connections first.
If you still have questions after going through the checklist, please consult
your local customer service representative.
Common Symptoms
Cause
The car ignition is switched off.
There is no power.
The fuse has blown.
The CDs cannot Presence of CD disc inside the player
be loaded.
The CDs are loaded The transport screws have not been
only halfway into removed.
the CD tray.
Inserting the disc in upside down
The device does
The surface of CD is extremely dirty
not work correctly
or it is damaged.
(EJECT, LOAD,
PLAY)
Temperature inside the car is too
high.
The volume control is set too low.
There is no sound.
The device has not been correctly
connected.
The operation keys 1.The built-in microcomputer is not
do not work operating properly due to noise
2.Front panel is not properly fix into
its place
The installation angle is more than
30 degrees
The surface of the road is uneven.
The sound of the
CD player skips
The surface of CD is extremely dirty
or it is damaged.
No radio reception. The antenna cable is not connected. Insert the antenna cable firmly into the
In automatic search The transmission signals are too
mode the radio does weak.
not stop at a trans-
mitting station.
Solution
If the power supply is properly connected to
the car accessory, switch the ignition key to
" ON " or " ACC " .
Replace another fuse according to the wiring
diagram.
Remove the disc in the player then put a new
upward.
Remove the transport screws before using.
Insert the compact disc with the label facing
upward
Clean the CD or try another CD, if this works
correctly, the first CD is properly damaged.
Cool off until the ambient temperature returns
to normal
Turn up the volume properly.
Check the power and earth connection
according to the wiring diagram.
1. Switch the device off and on again. Or press
the RESET button to resume the program.
2. Reinstall the front panel
Adjust the installation angle to less than 30
degrees
Wait until the road becomes smoother before
playing the CD.
Clean the CD or try another CD, if this works
correctly, the first CD is properly damaged.
antenna socket of the device.
Tune in to a radio station manually.
9

LOCATION AND FUNCTION OF CONTROLS

9 10
18 7
TA
SCN
3
AF
SEL
_
6
BND
VOL
+
4 PTY
TOP
MODE 1/ 1/
CLK
AUX
8 13 17 1 16
21
14
1. SEL( AUDIO MODE SELECT)BUTTON/VOLUME +/- KNOB
(1) Press SEL button shortly and repeatedly to change the mode in the sequence as follows:
--> VOL --> BAS --> TRE --> BAL --> FAD -->
1) VOLUME CONTROL
A) The volume level can be adjusted at any time by rotating the audio level VOL knob as
select mode has been initially defaulted at volume mode.
B) The volume level is also obtained by stepping through the SEL button until the function
VOL is displayed and then rotate VOL knob to adjust the sound level.
2) BASS CONTROL
A) Press the SEL button to select the bass mode until BAS appears on the display.
B) r otate VOL knob to adjust the bass effect.
3) TREBLE CONTROL
A) Press the SEL button to select the treble mode until TRE appears on the display.
B) r otate VOL knob to adjust the treble effect.
4) BALANCE CONTROL
A) Press the SEL button to select the balance mode until BAL appears on the display.
B) r otate VOL knob to increase or decrease the sound level of left or right speaker.
5) FADER CONTROL
A) Press the SEL button to select the fader mode until FAD appears on the display.
B) r otate VOL knob to increase or decrease the sound level of front or rear speaker.
2
CD/USB/MMC/MP3 PLAYER
USB
COMPACT
DIGITAL AUDIO
INT RPT RDM
2 3 4 5 6 A.P MUTE
5 11 15
12
20
23 22
2
19