KDS-70R2000 RM-ED006 SERVICE MANUAL SP-3 CHASSIS MODEL MODEL COMMANDER DEST COMMANDER DEST KDS-70R2000 KDS-70R2000 RM-ED006 RM-ED006 KDS-70R2000 RM-ED006 SXRD PROJECTION TV SXRD PROJECTION TV SXRD PROJECTION TV SXRD PROJECTION TV SXRD PROJECTION TV - 1 -...
DUE TO LIVE CHASSIS, THE CHASSIS OF THIS RECEIVER IS PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE DIRECTLY CONNECTED TO THE POWER LINE. THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com - 3 -...
KDS-70R2000 RM-ED006 i g i i g i i g i i g i i g i i g i . s l . s l . s l . s l e i l a j i c i t c i t "...
Page 5
KDS-70R2000 RM-ED006 y t i WARNING (UK Models only) A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience. Should the fuse in the plug supplied need to be replaced the same rating of fuse approved by ASTA or BSI to BS 1362 (i.e., marked with...
KDS-70R2000 RM-ED006 21 pin connector Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms...
KDS-70R2000 RM-ED006 SECTION 1 SELF DIAGNOSIS FUNCTION SP-3 Self Diagnostic Software SP-3 chassis TV’s contain a self diagnosis function. In the event of an error occurring, the STANDBY LED indicator will automatically begin to flash. The number of times the STANDBY LED indicator flashes translates to a probable source of the problem. If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past problems and how often these problems occur.
Page 8
KDS-70R2000 RM-ED006 3. STOPPING THE STANDBY INDICATOR FLASH Turn off the power switch on the TV to stop the STANDBY indicator from flashing. 4. SELF-DIAGNOSTIC SCREEN DISPLAY For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes off” that cannot be confirmed, it is possible to bring up past occurrences of failure on the screen for confirmation.
Page 9
KDS-70R2000 RM-ED006 5. SELF-DIAGNOSIS FUNCTION OPERATION Temp over When the inside temperature sensed with IC3150, IC3200 and IC2000 mounted on the S1 board, S2 board and C board respectively exceed the threshold, DEM (Display Engin u-com) detcts it and turns off the lamp.
KDS-70R22000 RM-ED006 3-5. FXE, TUE BOARDS 3-6. S1 BOARD 2 FXE Board Four screws (+BVST 3x6) 2 S2 Board 3 TUE Board 1 Ten screws 1 One screw Four screws (+BVST 3x6) (+BVST 3x6) (+BVST 3x6) Note: When removing or replacing the FXE board, take care not to damage the connector on the back.
Page 26
KDS-70R22000 RM-ED006 3-8. DC MOTOR SFF21C/C-NP 1 Screw (+BVTP 4x16) 4 2 Claws 3 Screw (+BVTP 4x16) DC motor SFF21C/C-NP – 26 –...
KDS-70R22000 RM-ED006 3-11. DC MOTOR SFF22B/C-NP 1 2 Screws (+BVTP 4x16) 3 Scirocco fan (DC motor SFF22B/C-NP) Scirocco fan cover 3-12. COVER UNIT Cover unit 2 Cover unit 1 7 Screws (+BVTP 4x16) – 28 –...
KDS-70R2000 RM-ED006 SECTION 4 SET-UP ADJUSTMENTS 4-1. PICTURE DISTORTION CORRECTION 4-2. ELECTRICAL ADJUSTMENT BY REMOTE MECHANISM COMMANDER By using remote commander (RM-ED006), all circuit adjustments can 4-1-1. V-TRAP Correction 1 be made. In case of movimg the V spacer by changing the position of center screw on the V spacer 2 to 1, the picture center NOTE : Test Equipment Required.
KDS-70R2000 RM-ED006 4-3. TEST RESET 4-2-3. Memory Write Confirmation Method 1. After adjustment, turn power off with the remote commander. The user settings can be reset to the factory default condition as 2. Turn power on and set to service mode.
KDS-70R2000 RM-ED006 AG.-SP-3(KDS-70R2000) CN8006 TO UE BOARD FB8012 COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL CN9301 FB8040 CN8001 STBY5V TU33V FB8000 AFT_M_GA TU33V AFT_M(CH/GA/AUS) R8109 XX FL8009 STBY+5V SIF_GA SIF_M(CH/GA/AUS) TU5V SUB (CH/GA) / MAIN (AEP) SWITCH...
Page 51
KDS-70R2000 RM-ED006 AG.-SP-3(KDS-70R2000) COMPONENTS MARKED AS XX ARE NOT FITTED ON THIS MODEL D3.3V 11V_DET Q8254 L8254 D8255 CN8250 R8305 RSQ035P03TR 10uH PTZ-TE25-3.9B DC/DC CONVERTER CHECK_D3.3V C8275 L8258 2 / 7 R8250 C8273 4 . 7 0.0022 D3.3V FAN_DRV FAN_DRV...
KDS-70R2000 RM-ED006 B2.-SP-3(KDS-70R2000) R4054 U2_TX U2_TX 1/12 VIDEO SIGNAL PROCESSING, PC INPUT, HDMI INPUTS 16.5V CN4000 OSD_HS L4003 R4055 XX SAIPH_OSD_HSOUT +16.5V R4056 XX C4020 C4014 OSD_VS +16.5V R4057 XX SAIPH_OSD_VSOUT R4058 XX SUB6.5V ICLK OSD_CLK R4059 XX C4021 L4000...
KDS-70R2000 RM-ED006 TO AG BOARD TO FXE BOARD TO AG BOARD TO AG BOARD TO AG BOARD CN8008 CN7501 CN8008 CN8008 CN8008 CN3901 CN3903 5VAEMI_F CN3802 CN3904 FB3913 FB3912 Note: 10V5 33V 33V_F C3929 R3959 TV_Dem_sel Condition C3920 NC(ON/OFF) Digital...
KDS-70R2000 RM-ED006 5-5. PRINTED WIRING BOARDS ~ AG Board Semiconductor Location Table Side A ~ ~ AG Printed Wiring Board Conductor Side A ~ - 93 -...
Page 94
KDS-70R2000 RM-ED006 ~ AG Board Semiconductor Location Table Side B ~ ~ AG Printed Wiring Board Conductor Side B ~ - 94 -...
KDS-70R2000 RM-ED006 SECTION 6 EXPLODED VIEWS NOTE : Items with no part number and no description are not Items marked “*” are not stocked stocked because they are seldom required for routine since they are seldom required for service. routine service. Some delay should...
SECTION 7 ELECTRICAL PARTS LIST PARTS LISTING TABLE OF CONTENTS Page S1 BOARD COMPLETE Parts List : ....................113 UE BOARD COMPLETE Parts List : ....................113 TUE BOARD COMPLETE Parts List : ....................121 B2 BOARD COMPLETE Parts List : ....................