Sony Handycam HDR-CX550 Service Manual page 7

1-5-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address Data
1 11 80 7430 01
2 11 8E F654 01
3 11 8E F655 F0
4 11 8E F658 01
5 11 8E F658 00
6 11 8E F654 00
7 11 8E F655 10
8 11 8E F658 01
9 11 8E F658 00
10 11 80 7430 00
11
12
13
14
15
16
Note1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address: F658, data: 00, and then retry.
Note2: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
HDR-CX550/CX550E/CX550V/CX550VE/XR550/XR550E/XR550V/XR550VE_L2
Procedure
Write the data. (After it starts, set it before caution is displayed.)
Write the data.
Write the data.
Write the data. (Note 1)
Write the data.
Write the data.
Write the data.
Write the data. (Note 1)
Write the data.
Write the data.
Check if the shift lens moves while setting the order 2 to 9. If the shift lens
does not move, replace the lens block (Note 2). When the shift lens moved,
proceed to the order 12.
While setting the order 2 to 9, measure with an oscilloscope the output
voltage of R5527 in the periphery of IC5501 on the VC-592 board to check
the output voltage varies.
If the output voltage does not vary, replace the lens block (Note 2). When
the output voltage varied, proceed to the order 14.
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5513 in the
periphery of IC5501 on the VC-592 board, turn the power ON to check
that the output voltage immediately after the power on change as shown
in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block
(Note 2). If it does not change as shown in Fig. 2, inspect the camera control
circuit (IC7501 of VC-592 board) periphery.
1-5-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address
1 11 80 7430
2 11 8E F656
3 11 8E F657
4 11 8E F659
5 11 8E F659
6 11 8E F656
7 11 8E F657
8 11 8E F659
9 11 8E F659
10 11 80 7430
11
12
13
14
15
16
Note1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address: F659, data: 00, and then retry.
Note2: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-5-4. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order
1 Turn the power ON.
2 Confirm the connections of flexible flat cables and connectors between the lens block and VC-592 board.
In case of no malfunction of connections, replace the lens block with new one (Note) . When the error has occurred in spite of
3
the lens replacement, replace VC-592 board with new one.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-3
Data Procedure
01 Write the data. (After it starts, set it before caution is displayed.)
01 Write the data.
F0 Write the data.
01 Write the data. (Note 1)
00 Write the data.
00 Write the data.
10 Write the data.
01 Write the data. (Note 1)
00 Write the data.
00 Write the data.
Check if the shift lens moves while setting the order 2 to 9. If the shift lens
does not move, replace the lens block (Note 2). When the shift lens moved,
proceed to the order 12.
While setting the order 2 to 9, measure with an oscilloscope the output volt-
age of R5524 in the periphery of IC5501 on the VC-592 board to check the
output voltage varies.
If the output voltage does not vary, replace the lens block (Note 2). When
the output voltage varied, proceed to the order 14.
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5513 in the
periphery of IC5501 on the VC-592 board, turn the power ON to check
that the output voltage immediately after the power on change as shown
in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block
(Note 2). If it does not change as shown in Fig. 2, inspect the camera control
circuit (IC7501 of VC-592 board) periphery.
Procedure
– ENGLISH –