SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
CONTENTS SERVICING NOTICES ON CHECKING ......................A1-1 HOW TO ORDER PARTS ..........................A1-1 IMPORTANT ..............................A1-1 CONTENTS ..............................A2-1 GENERAL SPECIFICATIONS ........................A3-1~A3-4 DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ......................... B1-1 2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ..............B2-1, B2-2 SERVICE MODE LIST .............................
Operation C ~ +40 Storage C ~ +60 G - 6 Operating Humidity Less than 80% RH G - 7 On Screen Menu Display Menu Type Disney Charecter Picture Contrast Brightness Color Tint Sharpness Reset Audio Bass Treble Balance BBE On/Off...
Page 5
GENERAL SPECIFICATIONS Stereo,Audio Output,SAP Video Color Stream Channel(TV/Cable) CH Label Sleep Timer Sound Mute V-chip Rating G - 8 OSD Language English French Spanish G - 9 Clock and Sleep Timer Max Time 120 Min Timer Step On/Off Timer Program(On Timer / Off Timer) Wake Up Timer Timer Back-up (at Power Off Mode) more than...
Page 6
UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card PTB Sheet 300 ohm to 75 ohm Antenna Adapter Safety Strap Disney Leaflet G - 1 3 Interface Switch Front Power System Select Main Power SW Sub Power...
Page 7
GENERAL SPECIFICATIONS DC Jack 12V(Center +) VHF/UHF Antenna Input F Type AC Outlet G - 1 4 Size Approx. W x D x H (mm) 510.0 x 442.5 x 572 510.0 x 442.5 x 488.5 w/o Speaker,Legs Approx. W x D x H (mm) G - 1 5 Weig ht Net (Approx.)
DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to 1. REMOVAL OF ANODE CAP remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
DISASSEMBLY INSTRUCTIONS REMOVAL AND INSTALLATION OF When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using FLAT PACKAGE IC a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) REMOVAL NOTE Put the Masking Tape (cotton tape) around the Flat...
Page 10
DISASSEMBLY INSTRUCTIONS INSTALLATION When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin- Take care of the polarity of new IC and then install the tip Soldering Iron. (Refer to Fig. 2-8.) new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Set Key Remocon Key Operations VOL.
ELECTRICAL ADJUSTMENTS BEFORE MAKING ELECTRICAL 2. BASIC ADJUSTMENTS ADJUSTMENTS 2-1: VIF VCO Read and perform these adjustments when repairing the Place the set with Aging Test for more than 10 minutes. circuits or replacing electrical parts or PCB assemblies. Receive an 80dB monoscope pattern. CAUTION Connect the digital voltmeter between the pin 5 of CP601 and the GND.
Page 13
ELECTRICAL ADJUSTMENTS 2-6: SUB TINT/SUB COLOR 2-8: VERTICAL SHIFT Receive the color bar pattern. (RF Input) Receive the monoscope pattern. Connect the oscilloscope to pin 6 of CP601 or TP023. Activate the adjustment mode display of Fig. 1-1 Activate the adjustment mode display of Fig. 1-1 and and press the channel button (07) on the remote press the channel button (22) on the remote control to control to select "V.SFT".
Page 14
ELECTRICAL ADJUSTMENTS 2-12: SUB CONTRAST Activate the adjustment mode display of Fig. 1-1 and press the channel button (17) on the remote control to select "CONT MAX". Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "80". Receive a broadcast and check if the picture is normal.
Page 15
ELECTRICAL ADJUSTMENTS PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator. minutes before performing the following adjustments.
Page 16
ELECTRICAL ADJUSTMENTS 4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION) CP806 J801 TP023 TP022 CP802B CRT PCB J704 CP601 FB401 TU001 CP502 FRONT JACK PCB DEGAUSS COIL J1151 S1153 S1152 CP101 S501B FRONT JACK PCB S501A J1150 CP1001 S1150 S1151 J1001 J701 J702...
BLOCK DIAGRAM TUNER/AV1/AV2 Lch SW IC TUNER/AV1/AV2 Rch SW IC VIDEO SW IC IC701 NJM2534V(TE2) J701 IC702 NJM2534V(TE2) J703 J704 J702 IC703 MM1501XNRE SOUND AMP IC(Rch) IC IC1001 AN7513 CHROMA IC IC601 M61250BFP MEMORY IC J1001 TU001 IC199 51 AUDIO OUT S-24C02BFJ-TB 38 EXT C IN RF AGC OUT...
Page 21
CHROMA SCHEMATIC DIAGRAM (MAIN PCB) FROM TV POWER UNREG+12V Q603 KTC3203_Y R623 120 1/4W FROM SOUND/AV 11.3 Q606 KTC3203_Y Q601 VIDEO_IN 11.3 KTC3203_Y Q605 Q604 KTC3203_Y KTC3203_Y FROM MICON/TUNER Q611 DTA114EKA R613 PROTECT_H 1K 1/4W Q609 KTC3875S_Y_RTK CF603 SFSRA4M50CF00-A0 R642 D605 11E1-EIC H.CTL...
Page 22
TV POWER SCHEMATIC DIAGRAM (MAIN PCB) CAUTION :FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 4A 125V (F501) FUSE. ATTENTION :POUR UNE PROTECTION CONTINUE LES RISQUES 4A 125V D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME TYPE 4A 125V (F501). TO SOUND/AV R517_1 D505...