Jacuzzi luxury series air baths installation and operation instructions (36 pages)
Summary of Contents for Jacuzzi HD84000
Page 1
LUXURY WHIRLPOOL BATH SERIES INSTALLATION AND OPERATION INSTRUCTIONS Jacuzzi Luxury Bath ® 14525 Monte Vista Avenue Chino, CA 91710 1-800-288-4002 www.jacuzzi.com HD84000...
Save these instructions for future use. Use the form below to record your model and serial number for future reference. Date Purchased Purchased From Installed By Serial Number Model Installer: Leave the manual for the homeowner. Homeowner: Read this manual and keep for future reference. Installation and Operation www.jacuzzi.com Page 3...
This is a professional grade product. A knowledge of construction techniques, plumbing and electrical installation according to codes are required for proper installation and user satisfaction. We recommend that a licensed contractor perform the installation of all Jacuzzi® Luxury Bath products. Our warranty does not cover improper installation related problems. CAUTION: When using this unit, basic precautions should always be performed, including the following: •...
It is the responsibility of the installer/owner to determine specific local code compliance prior to installation of the product. The Company makes no representation or warranty regarding, and will not be responsible for any code compliance. Product specifications are subject to change without notice. Installation and Operation www.jacuzzi.com Page 5...
All bathtub units are factory tested for proper operation and watertight connections prior to shipping. However, the unit must be retested by the installer prior to installation. Jacuzzi Luxury Bath is not responsible for any defect that could have been discovered, repaired, or avoided by following this inspection and testing procedure: Place the bathtub on a level surface, near appropriate electrical supply, water supply, and water drainage.
Framing A technical specifications manual has been included with your bathtub. The Technical Specifications Manual will contain pertinent information regarding your Jacuzzi Luxury Bath product. Locate the Technical Specifications Manual at this time. Frame out the space where the bathtub is to be located. The...
Page 8
Specifications Manual that corresponds with your bathtub. Make appropriate cuts to the subfloor to accommodate the drain. Jacuzzi’s Tru-Level™ base is a standard feature on all bathtubs. If the subfloor is level and a continuous surface, no other preparation is necessary. Proceed to the “Installation” section.
Watertight installation of the drain and overflow is the installer’s responsibility. Drain leakage is excluded from the Jacuzzi Luxury Bath warranty of this product OPTIONAL - If the Fuzion™ Wood Frame is not being used, please proceed to Step 2 in the Undermount Installation section.
Page 10
Please proceed to Step 3 in the Drop-In Installation section. Page 10 Fuzion™ Frame Figure 4 - Control Panel Figure 5 - Adhesive Application Figure 6 - Control Panel www.jacuzzi.com Luxury Whirlpool Bath Control Box Wire (Black Wire) Control Box Wire Adhesive) Inside of Bathtub...
Turn OFF power and do not use the bathtub until the source of the problem has been identified and corrected. Installation and Operation Reset Test Power Cord from Control Box to GFCI Circuit www.jacuzzi.com 4˝ (101mm) Power Cord from Heater Box to GFCI Circuit Heater...
Page 12
Air Valve Sensor Inside Inside Ambient LOGO Panel Blower Light 2 Light 4 Light 2 Light ILLUMATHERAPY LIGHTS LIGHTS www.jacuzzi.com Luxury Whirlpool Bath LEAD CONNECTIONS 4-WHITE-C 3-BLACK-H 2-RED-L SEE VIEW A 1-GREEN-GRD VIEW A 120VAC Pump 120VAC 20A GFCI PUMP/MOTOR...
Proper installation of the spout plumbing and compliance with local codes are the responsibility of the installer. Jacuzzi Luxury Bath does not warrant connections of water supply fittings and piping, fill systems, or drain/overflow systems. Nor is it responsible for damage to the bathtub which may occur during installation.
Page 14
Page 14 Maximum 2˝ (50mm) Thickness Level Subfloor Figure 10 Level Subfloor Figure 11 Uneven Subfloor Figure 12 www.jacuzzi.com Luxury Whirlpool Bath Tile or Finished Scrap Lumber Surface Substrate Member Support Floating Floor Compound Installation and Operation...
Meguiar’s #10 Mirror Glaze. If that is not available, use automotive rubbing compound followed by an application of automotive paste wax. • Major scratches and gouges which penetrate the acrylic surface will require refinishing. Call Jacuzzi Luxury Bath to find a service agent in your area. Installation and Operation...
General Operation Information All bathtubs manufactured by Jacuzzi Luxury Bath are designed for “fill and drain,” which means the bathtub should be drained after each use and filled with fresh water by the next bather. This is a health precaution, as these bathtubs are not designed to hold water continuously like pools or spas.
Page 17
(no air) to open (max air). The indicator lights will display the flow as it cycles from minimum to maximum. To turn off wave mode, press the (wave) button. Installation and Operation High High Left www.jacuzzi.com Right Page 17...
Controlling Whirlpool Direction and Flow Direction - All Jacuzzi jets, except the rotating neck jets, can be driectionally adjusted. To change the direction of the water flow, swivel the jet nozzle to the desired angle. The jets can be directed individually toward any location on your body to provide a hydromassage.
For best results, however, we recommend that you clean your whirlpool bathtub after each use using, Systems Clean™, our exclusive two-part plumbing system cleaner made specifically for whirlpool bathtubs. Systems Clean™ is available through an authorized Jacuzzi Whirlpool Bath Distributor or by calling us direct at 1-800-288-4002.
Minor scratches which do not penetrate the color finish can be removed by lightly sanding with 600-grit wet/dry sandpaper. Restore the gloss using Meguiar’s Mirror Glaze or automotive paste wax. Major scratches and gouges which penetrate the acrylic surface will require refinishing. Call Jacuzzi Luxury Bath to find a service agent in your area. Spinning Jet Maintenance If hair, or other types of debris, get caught in the bearings of these jets, it could cause them to stop spinning.
Chromatherapy lights do not operate If the unit is within the warranty period, contact Jacuzzi Whirlpool Bath Service Support at 1-800-288-4002 with your bath’s serial number before work is started. The serial number is located on the Specification/Serial Number Plate (see the following page).
If you need a referral for a service company near you, or need assistance with operation or maintenance-related questions, please call our Service Support Department at 1-800-288-4002. Visit our web site at http://www.jacuzzi.com/ for products, services, and an online copy of these Installation and Operation Instructions.
ALLOWED BY LAW. NOTICE: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. There are no warranties applicable to Jacuzzi Luxury Bath products except as expressly stated herein or as implied by applicable state and federal laws. The Company will not be responsible for any statements or representations made in any form that go beyond, are broader than or are inconsistent with any authorized literature or specifications furnished by the Company.
Page 24
The attached Warranty Registration MUST be filled out by the purchaser within thirty (30) days from purchase and received by Jacuzzi Luxury Bath in order for this warranty to become effective.
Page 25
INSTRUCCIONES PARA LA INSTALACIÓN Y EL FUNCIONAMIENTO Installation and Operation HD84000 SERIE DE BAÑERAS LUXURY WHIRLPOOL Jacuzzi Luxury Bath ® 14525 Monte Vista Avenue Chino, CA 91710 1-800-288-4002 www.jacuzzi.com www.jacuzzi.com ® Page 25...
Fecha de la compra Comprado a Instalado por Número de serie Modelo Instalador: Deje el manual para el propietario. Propietario: Lea este manual y consérvelo para referencia futura. Instalación y Operación Installation and Operation www.jacuzzi.com Page 27...
Éste es un producto de calidad profesional. Se requieren conocimientos de técnicas de construcción, fontanería e instalación eléctrica conforme a los códigos para la instalación apropiada y la satisfacción del usuario. Recomendamos que un contratista matriculado realice la instalación de todos los productos Jacuzzi® Luxury Bath. Nuestra garantía no cubre problemas relacionados con instalaciones inadecuadas.
Incapacidad para percibir el calor. Incapacidad para reconocer la necesidad de salir de la bañera. Desconocimiento de un peligro inminente. Daño fetal en mujeres embarazadas. Incapacidad física para salir de la bañera. PÉRDIDA DEL CONOCIMIENTO CON PELIGRO DE AHOGAMIENTO. www.jacuzzi.com Page 29...
Los daños o defectos en el acabado reclamados después de la instalación de la bañera están excluidos de la garantía. La responsabilidad de Jacuzzi Luxury Bath por daños durante el transporte finaliza contra entrega de los productos en buen estado al transportista.
Luxury Whirlpool Bath Estructura Se ha incluido un Manual de especificaciones técnicas con su bañera. El Manual de especificaciones técnicas incluirá la información importante relacionada a su producto Jacuzzi Luxury Bath. Haga uso del Manual de especificaciones técnicas en este momento. •...
Page 32
Realice los cortes adecuados en el contrapiso para ubicar el drenaje. La base Tru-Level™ de Jacuzzi es una característica estándar en todas las bañeras. Si el contrapiso está nivelado y tiene una superficie continua, no es necesario realizar otra preparación. Vaya a la sección “Instalación”.
La pérdida del drenaje no está incluida en la garantía Jacuzzi Luxury Bath de este producto. OPCIONAL – Si el marco de madera Fuzion™ no se utiliza, continúe con el Paso 2 en la sección de Instalación de montaje bajo cubierta.
Page 34
Page 34 Marco Fuzion™ Figura 5. Panel de control Figura 6. Aplicación del adhesivo Figura 7. Panel de control www.jacuzzi.com Bañera de hidromasaje de lujo Luxury Whirlpool Bath Cable de la caja de control (cable negro) Cable de la...
Desconecte la alimentación y no utilice la bañera hasta haber identificado y corregido el origen del problema. Instalación y Operación Installation and Operation Restablecer Prueba Cable de alimentación de la caja de control al circuito de GFCI www.jacuzzi.com 4˝ (101mm) Cable de alimentación del calentador al circuito de GFCI Calentador Page 35...
Page 36
1 temperatura interior 1 Luz del Panel interior 2 interior 4 LOGOTIPO ambiental 2 LUCES DE ILUMINOTERAPIA www.jacuzzi.com Bañera de hidromasaje de lujo Luxury Whirlpool Bath CONEXIONES DE ELECTRODOS 4-BLANCO-C 3-NEGRO-H 2-ROJO-L VER VISTA A 1-VERDE-GRD VISTA A 120VAC...
Manual de especificaciones técnicas. La instalación impermeable del drenaje es responsabilidad del instalador. La pérdida del drenaje no está incluida en la garantía Jacuzzi Luxury Bath de este producto. Instale el grifo en este momento. Se recomienda que el grifo sea instalado por un plomero calificado.
Page 38
Espesor máximo mínimo de 2” (50 mm) Contrapiso nivelado Figura 10 Contrapiso nivelado Figura 11 Contrapiso desnivelado Figura 12 www.jacuzzi.com Bañera de hidromasaje de lujo Luxury Whirlpool Bath Azulejo o Madera para superficie desecho terminada Sustrato Soporte del componente Compuesto...
• Será necesario volver a aplicar el acabado si los rayones y estrías penetran en la superficie acrílica. Llame a Jacuzzi Luxury Bath para localizar a un agente de servicio cercano a su domicilio. Instalación y Operación Installation and Operation Plantilla Borde de la bañera...
Información general sobre el funcionamiento Todas las bañeras fabricadas por Jacuzzi Luxury Bath están diseñadas para “llenar y drenar”, lo que significa que se debe vaciar la bañera después de cada uso y llenarla con agua limpia para el próximo baño. Esto es una precaución para la salud, ya que estas bañeras no...
Page 41
Las luces indicadoras mostrarán el flujo a medida que pasa de mínimo a máximo. Para desactivar el modo de olas, pulse el botón (de ola). Instalación y Operación Installation and Operation Baja Alta Baja Alta Izquierda www.jacuzzi.com Derecha Page 41...
Control de la dirección y del flujo Whirlpool Dirección: Todos los chorros de Jacuzzi, excepto los giratorios para el cuello, se pueden ajustar de modo direccional. Para cambiar la dirección del flujo del agua, gire la boquilla del chorro hasta el ángulo deseado.
Systems Clean™, nuestro exclusivo limpiador de dos componentes para sistemas de fontanería fabricado específicamente para bañeras de hidromasajes. Systems Clean™ se puede conseguir por medio de un distribuidor autorizado de Jacuzzi Whirlpool Bath o llamándonos directamente al 1-800-288-4002.
600. Restaure el brillo con Mirror Glaze de Meguiar o con cera en pasta para automóviles. Será necesario volver a aplicar el acabado si los rayones y estrías penetran en la superficie acrílica. Llame a Jacuzzi Luxury Bath para localizar a un agente de servicio cercano a su domicilio.
Las luces de cromoterapia no funcionan. Si la unidad aún se encuentra dentro del período de la garantía, comuníquese con Asistencia de Servicio Técnico de Jacuzzi Whirlpool Bath llamando al 1-800-288-4002 y verifique el número de serie de su bañera antes de que se inicie el trabajo. El número de serie está ubicado en la placa de Especificaciones/número de serie (consulte la página siguiente).
UTILICE EL MANUAL DE ESPECIFICACIONES TÉCNICAS PROVISTO CON EL PRODUCTO. Jacuzzi® Luxury Bath ha obtenido los listados de los códigos (normas) aplicables que suelen estar disponibles a nivel nacional para productos de este tipo. Es responsabilidad del instalador o propietario determinar el cumplimiento de los códigos locales específicos antes de instalar el producto.
AVISO: La presente garantía le otorga derechos legales específicos, y es posible que usted goce de otros derechos que varían de un estado a otro. No existen garantías que se apliquen a los productos Jacuzzi Luxury Bath excepto las estipuladas expresamente en la presente o las implícitas en las leyes estatales y federales pertinentes.
Page 48
También puede completar el registro que se encuentra abajo y enviarlo por correo a Jacuzzi a la dirección indicada a continuación. Para que esta garantía entre en vigencia, el comprador DEBE llenar el Registro de la garantía que se adjunta en un plazo de treinta (30) días a partir de la compra, y Jacuzzi Luxury Bath debe recibirlo.
Page 49
Luxury Whirlpool Bath SÉRIE DE BAINS TOURBILLONS DE LUXE DIRECTIVES D’INSTALLATION ET D’UTILISATION Jacuzzi Luxury Bath ® 14525 Monte Vista Avenue Chino, CA 91710 1-800-288-4002 www.jacuzzi.com Installation and Operation Page 49 HD84000 www.jacuzzi.com...
Date d’achat Acheté chez Installé par Numéro de série Modèle Installateur : laissez le manuel au propriétaire. Propriétaire : lisez ce manuel et gardez-le pour consultation future. Installation et utilisation Installation and Operation www.jacuzzi.com Page 51...
électrique conformes aux codes sont requises pour effectuer une installation adéquate à la satisfaction de l’utilisateur. Nous vous recommandons d’obtenir les services d’un entrepreneur agréé pour effectuer l’installation des produits Jacuzzi® Luxury Bath. Notre garantie ne couvre pas les problèmes causés par une mauvaise installation.
La responsabilité de Jacuzzi Luxury Bath quant aux dommages causés par l’expédition prend fin au moment de la livraison au transporteur de produits en bon état.
Cadrage Un manuel de spécifications techniques est offert avec votre baignoire. Le manuel de spécifications techniques comprend des renseignements utiles concernant votre produit Jacuzzi Luxury Bath. Localisez le manuel de spécifications techniques. Encadrez l’espace où sera installée la baignoire. Considérez les éléments suivants lors de la préparation de la zone :...
Page 56
Effectuez les coupes appropriées dans le sous-plancher pour accommoder l’évacuation. La base Tru-Level™ de Jacuzzi est une caractéristique standard sur toutes les baignoires. Si le sous-plancher est une surface continue de niveau, aucune autre préparation n’est requise. Procédez à la section « Installation ».
Toute fuite de l’évacuation est exclue de la garantie Jacuzzi Luxury Bath de ce produit. EN OPTION – si le cadre en bois Fuzion™ n’est pas utilisé, veuillez passer à l’étape 2 dans la section Installation en dessous.
Page 58
Page 58 Cadre Fuzion™ Figure 5 - panneau de commande Figure 6 - application de l’adhésif Figure 7 - panneau de commande www.jacuzzi.com Luxury Whirlpool Bath Fil de la boîte de commande (fil noir) Adhésif pour fil de la boîte de...
Arrêtez l’appareil et n’utilisez pas la baignoire avant que la source du problème n’ait été identifiée et corrigée. Installation et utilisation Installation and Operation Réinitialisation Essai Cordon d’alimentation de la boîte de connexion au circuit à GFCI www.jacuzzi.com 4˝ (101mm) Cordon d’alimentation de la boîte de chauffage au circuit à GFCI Appareil de chauffage...
L’installateur est responsable de l’installation adéquate du bec de plomberie et de la conformité aux codes locaux. Jacuzzi Luxury Bath ne garantit pas les connexions des conduites et des raccords d’alimentation en eau, les systèmes de remplissage ou les systèmes d’évacuation/de trop-plein. Elle n’est également pas responsable des dommages...
Page 62
5 cm (2 po) Épaisseur maximale Sous-plancher de niveau Figure 10 Sous-plancher de niveau Figure 11 Sous- plancher inégal Figure 12 www.jacuzzi.com Baignoires Whirlpool Spa Luxury Whirlpool Bath Carreaux Morceau de retailles de bois surface finie Substrat Membre de soutien Composé à plancher...
à polir automobile suivie de l’application d’une cire automobile en pâte. • Les égratignures et les rainures majeures qui pénètrent la surface acrylique devront être finies à nouveau. Communiquez avec Jacuzzi Luxury Bath pour trouver un agent de service dans votre région. Installation et utilisation Installation and Operation...
Renseignements généraux d’utilisation Toutes les baignoires fabriquées par Jacuzzi Luxury Bath sont conçues pour « remplissage et évacuation », ce qui signifie que la baignoire doit être vidée après chaque utilisation et remplie d’eau fraîche par le baigneur suivant. Il s’agit d’une précaution de santé puisque ces baignoires ne sont pas conçues pour conserver de l’eau...
Page 65
(maximum d’air). Les voyants lumineux afficheront le débit lorsqu’il passe du minimum au maximum. Pour éteindre le mode à vague, appuyez sur le bouton (vague). Installation et utilisation Installation and Operation Basse Haute High Droite www.jacuzzi.com Gauche Page 65...
Contrôle de la direction et du débit du tourbillon Direction - la direction de tous les jets Jacuzzi, à l’exception des jets rotatifs pour le cou, peut être réglée. Pour modifier la direction du débit d’eau, pivotez la buse du jet jusqu’à l’angle désiré. Les jets peuvent être dirigés individuellement vers tout endroit de votre...
Systems Clean™ notre nettoyant pour plomberie en deux parties exclusif conçu spécialement pour les bains tourbillons. Systems Clean™ est offert par les distributeurs de bains tourbillons Jacuzzi autorisés ou en composant directement 1-800-288-4002. Additifs pour baignoire N’utilisez pas des additifs pour baignoire à...
600 grains. Restaurez le lustre au moyen de Meguiar’s Mirror Glaze ou d’une cire automobile en pâte. Les égratignures et les rainures majeures qui pénètrent la surface acrylique devront être finies à nouveau. Communiquez avec Jacuzzi Luxury Bath pour trouver un agent de service dans votre région. Entretien des jets rotatifs Si des cheveux ou d’autres types de débris se prennent...
L’éclairage à chromothérapie ne fonctionne pas Si l’unité est encore couverte par la garantie, communiquez avec le service technique de Jacuzzi Whirlpool Bath au 1-800-288-4002 avec le numéro de série de votre baignoire avant d’effectuer toute réparation. Le numéro de série est situé sur la plaque de spécifications/numéro de série (reportez-vous à...
Si vous avez besoin d’une référence pour une entreprise de service près de chez vous ou si vous avez des questions concernant le fonctionnement ou l’entretien, veuillez communiquer avec notre service à la clientèle au 1-800-288-4002. Visitez notre site Web à http://www.jacuzzi.com pour les produits, les services et une copie en ligne de ces directives d’installation et d’utilisation.
Comfort, Comfort Plus, Pure Air®, Luxury, Salon™ Spa et Pure Air® II Jacuzzi Luxury Bath (« l’Entreprise ») offre la garantie limitée à vie expresse suivante à l’acheteur original des produits Jacuzzi® Luxury Bath offerts au sein des collections Comfort, Comfort Plus, Pure Air®, Pure Air® II et Luxury™ (« Baignoire ») qui a acheté la Baignoire pour un usage personnel ou unifamilial résidentiel («...
Page 72
Ou encore, vous pouvez aussi enregistrer votre produit en remplissant la fiche ci-dessous et en l’envoyant à Jacuzzi à l’adresse indiquée. L’enregistrement de garantie ci-joint DOIT être rempli par l’acheteur dans un délai de trente (30) jours de l’achat et reçu par Jacuzzi Luxury Bath afin que cette garantie soit en vigueur.