Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Targa LCD-Display 19"
Summary of Contents for Targa LCD-Display 19"
- Page 1 LCD-DISPLAY 19" User manual Targa Visionary LCD 19-6 Wide...
-
Page 2: Operating Notes
Targa Visionary LCD 19-6 Wide Operating Notes First of all, many thanks for choosing this high-end multiscan monitor. Before starting installation, please read this manual completely. Intended Use This TFT monitor is an IT electronic device. It may only be used for private use, not industrial or other commercial purposes. -
Page 3: Table Of Contents
Targa Visionary LCD 19-6 Wide Table of Contents Operating Notes................1 Intended Use .................... 1 Conformity ....................1 Table of Contents ................2 Safety Information................3 Warnings....................3 Disposal of Old Devices ................5 Getting started ................. 6 Back Panel Connectors ................7 Quick Guide .................... -
Page 4: Safety Information
Targa Visionary LCD 19-6 Wide Safety Information During the manufacturing and testing of this monitor, the safety of the future user was our main goal. However, inadequate operation or installation can cause damage to the device and harm to the user. - Page 5 Targa Visionary LCD 19-6 Wide Do not open the monitor’s housing. The high-voltage components inside the device may produce an electric shock even after the power cord has been disconnected. Do not use the device if the casing is damaged. If this happens, it must first be examined by authorized service personnel.
-
Page 6: Disposal Of Old Devices
Targa Visionary LCD 19-6 Wide If you notice any smoke, unusual noise or strange smells, switch off the LCD display immediately and pull the plug out from the wall outlet. Contact customer service. It is very dangerous to continue using the LCD display under these conditions. -
Page 7: Getting Started
Targa Visionary LCD 19-6 Wide Getting started Mount the supplied socket to the base of your LCD 19-6 Wide as indicated on the bottom of the base. Please check that delivery contents are complete using the list below: 1 - Monitor... -
Page 8: Back Panel Connectors
Targa Visionary LCD 19-6 Wide Back Panel Connectors Quick Guide 1. Connecting the Video Cable Power your monitor and computer off. Use the VGA cable (2) to connect the computer to the port (9) of the monitor. 2. Connecting the Audio Cable Use the audio cable (3) to connect the computer’s Audio Out... -
Page 9: Setting The Resolution
Targa Visionary LCD 19-6 Wide Setting the Resolution The recommended screen resolution for your LCD 19-6 Wide is 1440 x 900 (max. refresh rate 75 Hz). In the following we will explain resolution setting operating systems ® Windows XP and Windows Vista™. -
Page 10: Front Panel Controls
Targa Visionary LCD 19-6 Wide Front Panel Controls 11. Display / hide the OSD menu. 12. Decrease value / navigate downwards 13. Increase value / navigate upwards 14. Confirm setting 15. On/Standby Switch 16. Power indicator... -
Page 11: Setting The Menu Language
Targa Visionary LCD 19-6 Wide Setting the Menu Language You can display the OSD (On Screen Display) menu in your local language. Proceed as follows: 1. Press button 1 (11) on the monitor. 2. Press the button (12) to select the menu option “Setup Menu”. - Page 12 Targa Visionary LCD 19-6 Wide 4. Press the (12) or (13) buttons to select the desired value. 5. Wait until the menu disappears or press button 1 (11) twice to exit the menu immediately. DCR means „Dynamic Contrast Ratio“ and offers an optimum contrast by adjusting the display backlight automatically depending on the picture contents.
-
Page 13: Osd Menu
Targa Visionary LCD 19-6 Wide OSD Menu Via the OSD menu you can access multiple settings to customize the LCD 19-6 Wide according to your and your computer’s requirements. Use the buttons 11 to 14 (as described on page 9) to navigate the menu. - Page 14 Targa Visionary LCD 19-6 Wide Contrast/Brightness Opens the Contrast and Brightness menu. Press the buttons to choose an option and press button 2 to confirm. Then press the buttons to select the desired value. The Brightness option will be disabled while DCR is on.
- Page 15 Targa Visionary LCD 19-6 Wide Information Shows information about the input signal coming from your computer’s graphics card as well as the model and serial number of your monitor. Manual Image Adjust: To manually adjust the picture position. Horizontal Size sets the horizontal picture size.
- Page 16 Targa Visionary LCD 19-6 Wide OSD Time Out: After the set time, the OSD menu will disappear if you don’t perform any further settings. You can select values between 5, 15, 30 and 60 seconds. OSD Background Off: Press button 2 to enable or disable the coloured background for the OSD display.
-
Page 17: Advanced
Targa Visionary LCD 19-6 Wide Advanced Supported resolutions VESA 640 x 480 @ 75Hz 640 x 480 @ 67Hz 640 x 480 @ 70Hz 720 x 400 @ 70Hz VESA 800 x 600 @ 56Hz VESA 800 x 600 @ 60Hz... -
Page 18: Wall-Mounting
Targa Visionary LCD 19-6 Wide Wall-Mounting You can mount your LCD 19-6 Wide to the wall by using a VESA wall mount with a 100 x 100 mm receptacle. To do so, disassemble the base as follows: 1. Power the device off and unplug all cables and connectors. -
Page 19: Technical Specifications
Targa Visionary LCD 19-6 Wide Technical Specifications LCD Display 19.0” Wide TFT (16:10) Power Management Complies with Energy Star, VESA DPMS-compatible = 1 W Power on consumption: max. 45 W Supported Resolution max. 1440 x 900 Refresh rate max. 75 Hz Pixel size 0.285 x 0.285 mm... -
Page 20: Troubleshooting
Targa Visionary LCD 19-6 Wide Troubleshooting No power Make sure that the power cord is properly connected to the wall outlet and that the cables to the monitor are fixed properly into their respective ports. Connect a different electrical appliance to the wall outlet to verify that it is working properly. - Page 21 Targa Visionary LCD 19-6 Wide Type 2: Non-lighting pixel (a dark or black dot) even when it should light. Type 3: Abnormal or defective sub-pixels of the basic colours (e.g. steady lighting with half intensity, non-lighting of a specific colour, blinking or flickering, but not included in Type 1 or Type 2).
- Page 22 TARGA GmbH Lange Wende 41 D-59494 Soest Deutschland www.targa-online.com...