Page 1
USER’S MANUAL MANUEL DE L’UTILISATEUR MANUAL DEL USUARIO WB84U1D1...
Page 2
Interactive White Board Operating Instruction Before operating the unit, please read this manual thoroughly, and retain it for future reference. Safety Warning Before operating the unit, please read this manual thoroughly, and retain it for future reference. Placement Do not place the unit on an unstable cart, stand, tripod, bracket, table, or shelf. Do not expose the unit to direct sunlight and other sources of heat. Do not place the unit near appliances that create magnetic fields. Do not handle liquids near or on the unit. Never spill liquid of any kind into the unit Do not put heavy objects on top of the unit. Power Supply Check that the unit’s operating voltage is identical with your local power supply. Please unplug power supply and aerial plug during a thunder (lightening) storm. Please unplug power supply, when there is nobody at home or not using over a long period of time. Please protect power cord from any physical or mechanical damage. Please use power cord provided, don't modify or lengthen it. Please check and ensure AC source is grounded. For 55/65/70/84 inch Display equipment: Fuse rating in inlet is 6.3A, 250 VAC. LCD Screen Never use any other tough or sharp object to replace with the original touch‐write pen. Unplug the power supply before cleaning. Clean the screen with a soft dustless dry cloth. Never use water or detergent to clean the unit. For deep clean, contact an authorized service center. Please don't display the high brightness image on the screen for a long time. Observation Distance The best distance between audience and screen is 5‐7 times that of screen size diagonally. The best watching angle between audience and screen is within 176 degrees. Temperature Do not place the unit near a radiator or heater. If your unit is suddenly moved from a cold to a warm place, unplug the power cord for at least two hours ...
Page 3
Battery Properly maintain the batteries and recycle the used batteries. Caution This is a Class B product , there is not cause radio interference. ...
1 INSTALLATION 1.1 Open the package Step‐1: Take out the carton handles. Step‐2: Move‐Up the carton body. Step‐3 : Take Off EPE packing material & Left IWB display . Step‐4: Be careful to Move out IWB display. It is heavy and easy to be slide, Please carefully and better Wear gloves when move display from carton box . 1.2 Checking parts Warranty Card, Quick Connect Guide, Remote Control, Power Cord, VGA/USB/Audio/AV/YPBPR cables, Batteries, handwritten pen and DVD. ...
1.3 Installation The IWB Stand (matched) takes material object as the standard, Please read “IWB Stand Installing Instruction” while installing. 1.3.1 Mounting Bracket tie‐up to IWB display ...
Page 7
IWB Back View Please follow above picture , Tie‐UP mounting bracket to IWB display by 3 screws on each ...
3 INPUT / OUTPUT TERMINALS Rear Bottom Terminals Rear Right Side Terminals USB terminal for touch panel. 1. USB TOUCH (USB: DC5V, 500mA) 2. RS232 Serial control interface, Used for transfer data/commands 3. EARPHONE Earphone Signal Output. 4. COAX SPDIF‐audio Output (Digital sound signal interface ) For YPbPr signal input ( Connected to DVD, set ‐top –box etc. with YPbPr 5. YPBPR(Y) output device ). Y component signal input to this RCA Jack (G) For YPbPr signal input ( Connected to DVD, set ‐top –box etc. with YPbPr 6. YPBPR(PB) ...
Page 10
14. HDMI 1 High Definition Multimedia Interface‐1 15. HDMI 2 High Definition Multimedia Interface‐2 16. POWER PC Turn ON/OFF the internal PC power (if installed) Internal PC reset, suspends all programs currently running, the PC system 17. RESET PC re‐starts NOTE: Functions related to PC will only work if internal PC is installed. ...
4.2 Remote Control Instruction Insert the Batteries 1 Remove the cover on the rear of the remote control 2 Insert two “AAA” batteries 3 Place the cover 4.3 Remote control range The range of remote control receiver as shown below: ...
5 CONNECTION GUIDE For the safety of you and your unit, please do not connect any power source before the external device is installed. 5.1 External Computer and Touch Connecting (1) Connect a VGA cable (15pin) between the PC‐VGA Input and Output of external PC. Connect an audio cable between the PC and display. (2) Connect a USB cable between the external PC and USB terminal (3) Plug‐in the POWER cord and switch the display on. (4) Start the external computer that touch function will be activated in free of driver. (5) Press IWB main power switch to ON position ( ) to turn the display on. (6) Press Source button to select INPUT to VGA 1 or VGA 2 corresponding to external PC connection. Caution : Touch USB connected to external PC for White Board application, free of driver for touch panel. Just simply connect external PC and white board can be activate. In case you use Inside PC for white board,, inside has connection for OPS. You need remove USB cable for External PC. Touch panel only support one PC operation. Both PC connection will cause error in writing or Break of strokes. ...
5.2 AV Connection (1) Connect an AV cable between display and external device through the AV out. Yellow is Video, Red is Audio‐R, White is Audio‐L . (2) Plug‐in the POWER cord and turn ON the display. (3) Press main power switch located on the front of the display to IN position to turn the power on (4) Press INPUT to change source to AV. 5.3 Y‐Pb‐Pr INPUT (1). Connect the Y‐Pb‐Pr cable between the display and an external device. (2). Plug‐in the POWER cord and switch it on from the rear panel. (3). Press main power switch to turn the power on. (4). Press INPUT to change source to YPbPr. ...
5.4 HDMI1 / HDMI2 INPUT (1) Connect a HDMI cable from the display to an external device. (2).Plug‐in the POWER cord and switch it on from the rear panel. (3) Press main power switch to turn the power on. (4) From the external device select input source to HDMI. 5.5 COAXIAL CONNECTION (SPDIP AUDIO OUTPUT) (1) Connect a Coaxial cable from display to an external device. (2) Plug‐in the POWER cord and switch it on from the rear panel. (3) Press main power switch to turn the power on ...
6 RS232C COMMUNICATION After connecting the central control system and unit, you can use RS232 control some of the function, such as power on/off or adjust the volume etc. 6.1 RS232C Baud speed: 9600bps Bit number: 8 bit Odd Parity: None Stop bit: 1 bit 6.2 Protocol Function Protocol (16th) Code POWER ON F6 01 01 00 F8 6F 0x01 ...
Page 16
In the Protocol list (command list), ID=01 (0x01) is used. 0xF6: command start bit 0x6F: command end bit ...
7 INSIDE PC UNIT INSTALLATION/REPLACEMENT (OPTION) This PC unit (IWB PC‐02)is compatible with WB84U1D1 only, do not intend to attach this unit to the other models. Be sure Turn‐off the TWB Monitor before installation of inside PC. CAUTION 1. Power supply of inside PC and HDMI signal to IWB display are connected by internal 40‐pin connector. Before installation, check if something clogged at the connector‐pin area, if so, remove them and keep the connector clean. Insert inside PC to slot, gently and smooth pushing is highly recommended. After insert inside PC, be sure to tighten both 2‐handheld screws to fasten pc securely. 2. There have 2‐ Wifi Antenna provided inside package . When you feel wifi signal is strong enough , You Could only use one antenna. When you need stronger Wifi signal, 2‐Antena are possible to be both used together. 3. On Inside PC unit back side, a +19V DC power supply input Jack, Only for unit service purpose. Don’t insert DC adopter in normal application . 7.1 Inside PC basic operations After installation of the PC unit, its operation is based on the IWB mother monitor Operation. To turn ON or OFF IWB there have main switch and remote control to access. ...
At the right side of the IWB Monitor & at lower portion, Input terminals and switches are located. There are two switches, one for “PC Power” and the other “for PC reset”, they are the switches related to this Optional PC unit operation. The PC Power switch is a “cyclic type”, push‐ON, push‐OFF and PC Reset is push‐make contact type. Push Power PC button to switch ON PC Wait about 30 seconds after installing PC at back of the display, press POWER to turn on the Monitor and PC together. Push Power PC button to switch OFF PC Press the POWER button, wait for 2 to 3 seconds and then, press the power button again to turn off the Monitor and PC together. Monitor ON, PC OFF While using PC source, select "WINDOWS" on the lower left corner of the desktop or press the "WINDOWS" button on the remote control, and then select "off", then, the PC turns off but keep the Monitor on. PC ON When turn on the Monitor, the PC is normally off. It is possible to turn on the PC by pressing the INPUT button of the monitor to select PC. PC RESET ...
8 OSD OPERATION 8.1 Instruction for main menu 8.1.1 Appearance 8.1.2 Operation of keys under main menu Function key Main Sub Exit from Main Menu Return to Main menu menu Exit from Main Exit Exit Menu menu ...
8.2 Function introduction of submenu 8.2.1 Picture submenu 8.2.1.1 Appearance 8.2.1.2 Function introduction Item Variable range Default Explanation Pressing button for Picture Mode Change Standard / Dynamic Picture Mode Standard Over. /Movie / User You will need to watch the picture Contrast 0‐‐‐‐100 50 when you adjust it, so,we close the main menu, pop up Contrast small menu Bright 0‐‐‐‐100 50 ...
Note: We set default setting as bellow, and you can change them to proper value for your product. Standard:Contrast = 50,Brightness = 50, Color = 50, Sharpness =50。 Dynamic:Contrast = 70,Brightness = 60, Color = 60, Sharpness =60。 Movie :Contrast = 45,Brightness = 40, Color = 50, Sharpness = 50。 User:Contrast = 50,Brightness = 50, Color = 50, Sharpness = 50。 8.2.2 Audio submenu 8.2.2.1 Appearance 8.2.2.2 Function introduction Item Variable range Default Explanation Standard / Music/ Sound Mode Standard Movie /User 0‐‐‐100 Bass ...
Page 22
8.2.3 Time submenu 8.2.3.1 Appearance 8.2.3.2 Function introduction Item Variable range Default Explanation Pressing Button to Off/5Min/10Min/15Min/30Min select one of Sleep Sleep Timer /45Min/60Min/90Min/120Min Timer setting. /180Min/240Min Pacific(UTC‐8)/ Alaska(UTC‐9)/ Default value can be Hawaii(UTC‐10)/ modified according ...
Page 23
8.2.4.2 Function introduction Item Variable range Default Explanation Now there are only three kinds of English / French language for OSD, if clients need Menu Language English more, we can add the language /Spanish according to your needs. Non VGA channel: Wide/Zoom/Cinema Only can be adjusted when there is ...
Page 24
8. 3 Hot Key Menu 8.3. 1 Info Key Note: 1、 If it is Display menu, then press INFO key to close the menu. It is also used to open Display menu 2、 After closing MENU and Source Input menu,Press INFO key, display menu will automatically pop up 3、 No operation for 3 seconds, then it is closed automatically ...
Sound Mode key works only when there is signal. If it is S‐Mode Sound Mode menu, then change options of S‐Mode (order is same with that (S‐Mode) in main menu), or, it is used to open S‐Mode menu MEMU Exit from S‐Mode menu, open main menu EXIT Exit from S‐Mode menu No operation for 3 seconds, then exit from S‐Mode menu ‐‐‐‐‐ 8.3.4 Sleep Press Sleep key, Sleep timer menu appears on lower portion of screen. Key's functions: keys Function If it is Sleep menu, then change the options of sleep, or, it is used to open TIMER Sleep menu。 MEMU Exit from Sleep menu, open main menu ...
Key's functions: keys Function If it is Source menu, Press for close Source Menu. or, Press it to open Source Source Menu Exit from Source menu, open main menu MEMU EXIT Exit from Source memu Used to change selection. RIGHT ‐‐‐‐‐‐‐‐‐ LEFT Cursor moves to last ITEM Cursor moves to next ITEM DOWN Used to change channel OK/Enter ▲▼ "Source Menu " Appear on screen, use " / " to Navigate of each input source . Press "Enter" to make the input selection. ...
Page 27
If it is Volume menu, then volume will increase RIGHT If it is Volume menu, the volume will decrease LEFT Note: No operation for 3 seconds, then Exit from Volume menu 8.3.8 MUTE menu Press Mute Key to open Mute Menu. Press once again, Mute Menu closed. Note: 1、Make sure MUTE menu exist with other menu, only MUTE key can close MUTE menu 2、When MUTE menu displays, if the option of CC Mode is On, then close MUTE menu. 3、If option of CC Mode is CC On MUTE, then press MUTE key to open MUTE ...
Page 28
9 USB Input mode 9.1 Introduction Select USB port from Input Source menu, then system in USB input status. In USB Input Mode , Only JPEG & M‐JPEG signal format can be support. The system automatically Identified file format , Only show the support file. 9.2 Appearance 9.2.1 Non Input Mode If No USB module inserted, Top and left of screen appear “ No device”. ...
11 RESOURCE DVD At accessory box , you could find a DVD disk. There are documents as below : 1) User’s Manu for WB55FiD1/WB65F1D1/WB70F1D1 (UM); 2) User Manual for WB84U1D1(UM) 3) WScribe Program for White Board (SW) 4) User’s Manu for White Board Program of WScribe (UM) 5) WScribe Program quick installation guide (QIG) 6) Driver Program for IWB PC‐01 & IWB PC‐02 Please follow the Quick Instruction Guide to install WScribe program and activate for White Board application. Wscribe activate Key & procedure 1) Checking parts: Accessory DVD as below picture. 2) Activate process: Wscribe is not registered, Please check on DVD registration code 20 BITs, Its location on DVD surface ( Reference red circle). Please follow WScribe Installation Guide to activate step by step. 3)DVD Interface Open DVD,following Interface could be seen. You can select what you need: ...
When you need driver for PC, you can select IWB PC 01 Drivers for WB55、WBWB65、WB70。 For WB84,should select TWB PC‐02 Drivers。 12 TROUBLE SHOOTING Remote control: 1 .Check whether there is an object between remote control and IWB no function display. 2. Check whether the batteries polarity in remote control is correct. 3. Check whether the batteries are exhausted. The unit shuts down 1. Check sleep function if activated. automatically 2. Check whether there is a sudden power failure. 3. Check for the signal to system and control. PC mode No signal 1. Check display setting. 2. Check the resolution. 3. Adjust the Hs & Vs (synchronization) in the menu. Background streaking 1 .Choose auto‐adjust. 2. Adjust clock and phase. Wrong color 1. Check the VGA. 2. Adjust color, tint, brightness and contrast in case of AV‐input ...
Page 32
No Touch 1. Check setup. Function 2. Check whether the touch pen is working properly. Remarks This IWB with 2‐ Touch USB, But it is option use with PC. It is not recommend both touch USB port connect with PC same time. Video not working properly No picture/No sound 1. Check POWER status. 2. Check the signal cable. 3. Check the PC source. Pixelization 1. Check the signal cable. 2. Check for other electronics signal interferences. 1 .Adjust chroma, brightness and contrast in the menu. Poor picture quality 2. Check the signal cable. Audio not working properly 1. Check the mute function if operated. No sound 2. Adjust sound volume. 3. Check the audio cable. 1. Adjust sound balance in the menu. One speaker ...
Page 33
S/N: Westinghouse Digital International Orange, CA SE-UM-0103-1301...