COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CL-38 FACTORY MODEL: LM505J MODEL: L1510M (LM505J-GL) CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
PRECAUTION WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING BE CAREFUL ELECTRIC SHOCK ! • There are some special components used in LCD monitor that are important for safety. These parts are • If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and the inverter circuit, must disconnect the AC adapter...
TIMING CHART VIDEO SYNC Total Video Blanking Sync Back Front Sync Frequency MODE H / V Resolution Period Active Time Duration Porch Porch Polarity Clock ( E ) Time ( A ) ( B ) ( D ) ( F ) ( C ) 25.175 31.468 KHz...
OPERATING INSTRUCTIONS FRONT VIEW REAR VIEW HEAD PHONE AUDIO IN Power Connector See front control panel D-Sub Signal Connector Front Control Panel 1. Power Button 4. AUTO/SELECT Button Use this button to turn the display on or off. Use this button to enter a selection in the On <Power (DPMS) Indicator>...
Page 6
OPERATING INSTRUCTIONS Front Control Panel 5. LIGHT VIEW CONTROLS LOCKED/UNLOCKED This function optimizes the brightness, contrast or : MENU and Button for 3 seconds color value to the surrounding conditions and Use this button to enter or exit the On Screen settings and enables you to enjoy the most suitable Display.
DESCRIPTION OF BLOCK DIAGRAM 1. Scaler One chip IC(GMZAN-2, U201) GMZAN-2 (U201) is one chip IC which it supports four internal function blocks of Video Amp, PLL, A/D converter and Video processor. Video signal (0.7Vp.p) clamped through C209, 208, 207 with matching IC’s proper cut off voltage. This signal is processed as a proper 8 bit digital signal by U201’s amplifying, phase locking, A/D converting, and scaling operations.
ADJUSTMENT All adjustment are thoroughly checked and corrected when the monitor leaves the factory, but sometimes 2. Adjustment for White Balance several minor adjustment may be required. 1) Display color 0,0 pattern at Mode 13. Adjustment should be following procedure and after 2) Set External Bright to MAX position and Contrast to warming up for a minimum of 10 minutes.
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK POWER CHECK J707 BOARD, AND FIND VOLTAGE OUT A SHORT POINT PIN1&PIN2(12V) AS OPENING PIN4(5V)? EACH POWER LINE CHECK U501 PIN 8 CHECK U803. VOLTAGE (5V) ? CHECK CHECK 5VS LINE U805 Voltage (OPEN CHECK) (5V) ?
Page 12
2. NO RASTER (OSD IS NOT DISPLAYED) – INVERTER NO RASTER (OSD IS NOT DISPLAYED) J705 PIN1 CHECK POWER BOARD 12V? CHECK MICOM INV J705 PIN8 ON/OFF PORT. 1. CONFIRM BRIGHTNESS OSD CONTRL STATE. J705 PIN7 2. CHECK MICOM DIM-ADJ PORT CHECK PULSE AS...
Page 13
3. NO RASTER (OSD IS NOT DISPLAYED) – gmZAN2 NO RASTER (OSD IS NOT DISPLAYED) U201 POWER PINS CHECK U802, U806 3.3V? 1. CHECK PIN141, 142 U201 PIN141, 142 SOLDERING CONDITION OSCILLATE AS 20MHz? 2. CHECK X201 3. TROUBLE IN U201 U401 PIN31 IS 65MHz CLOCK? PIN27 IS 48KHz H-SYNC?
Page 14
4. NO RASTER (OSD IS DISPLAYED) – gmZAN2 NO RASTER (OSD IS DISPLAYED) U201 POWER PIN CHECK U802, U806 3.3V? 1. CHECK PC CHECK R,G,B INPUT? 2. CHECK SIGNAL CABLE & D-SUB CONNECTOR U201 PIN 87, 91, 95 LINE CHECK CHECK H-SYNC LINE H-SYNC INPUT (D-SUB→U701→MICOM...
PRINTED CIRCUIT BOARD 1. MAIN BOARD 2. AUDIO BOARD...
Page 16
3. POWER BOARD(Component Side) 4. POWER BOARD(Solder Side) 5. CONTROL BOARD LIGHT-VIEW MENU DOWN LEFT RIGHT SELECT MUTE SW301 SW302 SW306 SW303 SW304 SW305 SW307 SW308 SW309 R308 POWER R302 R307 ZD302 LED301 Model:LM505J-KEY Date:2002.07.10 J301 P/N:6870T516C10 R301...
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS DATE: 2002. 7. 15. DATE: 2002. 7. 14. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC.