nstructon manual contans mportant operatng nstructons RWARNING! NEVER connect the transcever to a for the IC-F5062 and IC-F6062 VHF/UHF MOBILE TRANS- power source of more than 16 V DC such as a 24 V battery. CEIVERS. Ths connecton wll run the transcever.
■ Rear panel connecton ............14 ■ Suppled Accessores ............16 Icom optonal equpment s desgned for optmal perform- ■ Mountng the transcever ............16 ance when used wth ths transcever. We are not respon- ■ Antenna .................17 sble for the transcever beng damaged or any accdent ■...
PANEL DESCRIPTION ■ Front panel Function display (p. 2) Speaker I c o m I n c . q AF VOLUME CONTROL KNOB [VOL] y MICROPHONE CONNECTOR Rotate the knob to adjust the desred audo output level. Connect the suppled or optonal mcrophone. •...
PANEL DESCRIPTION ■ Function display u CALL CODE MEMORY INDICATOR ➥ Appears when the call code memory s selected. ➥ Appears when a phone call s receved.* I c o m I n c . i SCROLL INDICATOR Appears when the SDM, ncludes more than 12 charac- ters, s selected durng the receved message selecton mode* o SDM INDICATOR...
ZONE UP AND DOWN KEYS [P0], [P1], [P2], [P3] and [P4] programmable functon keys. Push to select an operatng zone. Consult your Icom dealer or system operator for detals con- SCAN A KEY cernng your transcevers programmng. ➥ Push to start and cancel scannng operaton.
Page 7
PANEL DESCRIPTION SCAN ADD/DEL (TAG) KEY MONI (AUDI) KEY ➥ Push to add or delete the selected channel to/from the ➥ Push to mute and release the CTCSS (DTCS) or 2-tone scan group. squelch mute. Open any squelch/deactvate any mute 1.
Page 8
PANEL DESCRIPTION RX SPEAKER KEY TONE/RAN CH SELECT KEY Push to turn the RX speaker functon ON or OFF. ➥ Whle n analog mode operaton, push to enter the con- When the RX speaker functon s turned ON, the receved tnuous tone channel selecton mode.
Page 9
PANEL DESCRIPTION TALK AROUND KEY EMERGENCY KEY Push to turn the talk around functon ON and OFF. Push and hold to transmt the emergency call. • The talk around functon equalzes the transmt frequency to the • The emergency call transmts wth beeps; the dsplay does not receve frequency for transcever-to-transcever communcaton.
Page 10
PANEL DESCRIPTION TX CODE CHANNEL UP/DOWN KEYS USER SET MODE KEY Push to select a TX code channel drectly. ➥ Push and hold for 1 sec. to enter user set mode. • Durng user set mode, push ths key to select an tem, and change the value or condton usng push [CH Up]/[CH Down].
BASIC OPERATION ■ Turning power ON ■ Channel selection q Push and hold [ ] for 1 sec. to turn the power ON. Several types of channel selectons are avalable. Methods w If the transcever s programmed for a start up password, may dffer accordng to your system set up.
BASIC OPERATION ■ Call procedure ■ Receiving and transmitting Receiving: When your system employs tone sgnalng (excludng CTCSS and DTCS), a call procedure may be necessary q Push and hold [ ] for 1 sec. to turn the power ON. pror to voce transmsson.
BASIC OPERATION D Transmitting notes D TX code channel selection • Transmit inhibit function If the transcever has [TX Code CH Select] assgned to t, The transcever has several nhbt functons whch restrct the ndcaton can be toggled between the operatng channel transmsson under the followng condtons: number (or name) and TX code channel number (or name).
BASIC OPERATION D TX code number edit (PMR operaton only) USING [TX CODE ENTER] KEY: If the transcever has [TX Code CH Select] or [TX Code Enter] assgned to t, TX code contents can be edted wthn q Push [TX Code Enter] to enter the TX code edt mode. •...
BASIC OPERATION ■ User set mode e Push [P0] several tmes to select the approprate tem. User set mode s accessed wth [User Set Mode] and allows you to set seldom-changed settngs. In ths case you can Then, push [Up] or [Down] to set the desred level/cond- ton.
BASIC OPERATION ■ Scrambler function ■ Stun function The voce scrambler functon provdes prvate commun- When the specfied ID, set as a kll ID, s receved, the stun caton between statons. The frequency nverson type s functon s actvated. equpped to all versons, moreover, the optonal Rollng or When the kll ID s receved, the transcever swtches to the Non-rollng type can be avalable.
CONNECTION AND MAINTENANCE ■ Rear panel connection D For mobile operation ANTENNA CONNECTOR D-Sub 25-pin Antenna Connects to an antenna. Contact your deal- Connect an external unit. Optional er about antenna selection and placement. speaker EXTERNAL SPEAKER JACK Connect a 4–8 external speaker. Microphone R C AU T I O N ! N E V E R remove the fuse-holder...
Page 18
CONNECTION AND MAINTENANCE ■ Rear panel connecton (Contnued) D For base station operation To antenna Microphone ANTENNA CONNECTOR EXTERNAL SPEAKER JACK DC power IGNITION LEAD Connect a 4–8 ø supply 13.2 V D-Sub 25-pin external speaker. Connect an external unit. DC POWER to an Optional speaker...
CONNECTION AND MAINTENANCE ■ Supplied Accessories ■ Mounting the transceiver The unversal mountng bracket suppled wth your trans- Microphone Microphone hanger Microphone cever allows overhead mountng. and screw set hanger cable • Mount the transcever securely wth the 4 suppled screws to a thck surface whch can support more than 1.5 kg.
CONNECTION AND MAINTENANCE ■ Antenna ■ Options • RMK-3 + OPC-609 A key element n the performance of any communcaton separation kit separation cable systems s an antenna. Contact your dealer about antennas Allows you to nstall the transcever man unt separately and the best places to mount them.
EN 300 113-2 v1.3.1 (December 2003) vii) EN 301 166-2 v1.1.1 (December 2001) CE Versons of the IC-F5062 and IC-F6062 Ths warnng symbol ndcates that ths equp- whch dsplay the “CE” symbol on the seral ment operates n non-harmonsed frequency...
Page 22
EN 300 219-2 v1.1.1 (March 2001) EN 300 113-2 v1.3.1 (December 2003) EN 301 166-2 v1.1.1 (December 2001) vii) About e-marking: Detaled nstallaton notes for Icom moble transcevers to be fitted nto vehcles are avalable. Please contact your Icom dealer or dstrbutor.