Shower stool / shower- and toilet chair (48 pages)
Summary of Contents for Invacare Patriot
Page 1
PATRIOT Et PATRIOT DEALER: KEEP THIS MANUAL. THE PROCEDURES IN THIS MANUAL MUST BE PERFORMED BY A INVACARE DEALER ONLY. FOURNISSEUR: CONSERVEZ CE MANUEL. LES PROCÉDURES CONTENUES DANS CE MANUEL DOIVENT ÊTRE EXÉCUTÉES PAR UN FOURNISSEUR INVACARE SEULEMENT.
It is Invacare’s position that users of wheelchairs should be transferred into appropri- ate seating in vehicles for transportation and use be made of the restraints made available by the auto industry.
Any change to one (1) or any combination of the eight (8) may cause the wheelchair to decrease in stability. These adjustments MUST be performed by an authorized Invacare dealer or qualified technician.
Page 6
Inasmuch as the anti-tippers are an option for 0 or 3 on this wheelchair (You may order with or without the anti-tippers), Invacare strongly recommends using the anti-tippers as a safeguard for the wheelchair user. Seat-to-floor angle of 6 : If changing the seat-to-floor angle to 6 , anti-tippers MUST be installed.
ASSEMBLY PROCEDURE 2 5. If necessary, convert standard axle to amputee. Re- This Procedure Includes the Following: fer to CONVERTING FROM STANDARD AXLE TO Assembling the Wheelchair AMPUTEE for Patriot in PROCEDURE 6 OR CON- VERTING FROM STANDARD AXLE TO AMPU- ASSEMBLING THE WHEELCHAIR TEE for Patriot SL in PROCEDURE 7 of this manual.
PROCEDURE 3 ARMS Installing This Procedure Includes the Following: Removing/Installing Front Arm Socket/Seat Guide 1. Install the NEW front arm socket/seat guide as shown in FIGURE 1. 2. Install the EXISTING mounting screw through the front WARNING arm socket/seat guide. After ANY adjustments, repair or service and BEFORE use, make sure all attaching 3.
SEAT/BACK PROCEDURE 4 ADJUSTING/REPLACING THE This Procedure Includes the Following: BACK CANES Replacing Rear Seat Guides Adjusting/Replacing the Back Canes WARNING BEFORE performing this procedure, refer to Replacing the Sector Block SPECIFIC WARNINGS - STABILITY in PROCEDURE Adjusting the Seat Width 1 of this manual for additional requirements.
PROCEDURE 4 SEAT/BACK PATRIOT (FIGURE 3). Replacing (FIGURES 2 AND 3) 1. Remove the one (1) mounting screw and locknut that 1. Cut the tie wraps that secure the EXISTING back up- secure the back cane to the wheelchair. holstery to the wheelchair frame. 2.
SEAT/BACK PROCEDURE 4 NOTE: Note the orientation of the coved washers, wash- Wheelchair ers and locknut for assembling the NEW crossbraces. Frame See DETAIL "A". Locking Pin Washer 6. Remove the mounting screw, coved washers, wash- ers and locknut that secure the two (2) crossbraces together.
WHEELS PROCEDURE 5 4. Slide the NEW six or eight-inch caster/fork assembly This Procedure Includes the Following: into the caster headtube. Removing/Installing the Rear Wheels 5. Secure the NEW six or eight-inch caster/fork assem- Replacing Six or Eight-Inch Caster/Fork Assembly bly with the EXISTING locknut.
PROCEDURE 5 WHEELS CONVERTING FROM TRAILING TO Leading to Trailing (FIGURE 4) LEADING OR LEADING TO 1. Remove the two (2) mounting screws, four (4) coved TRAILING CASTERS spacers, washer, cam and two (2) locknuts that se- cure the caster headtube to the wheelchair frame. Trailing to Leading (FIGURE 3) 2.
WHEELS PROCEDURE 5 2. Remove the mounting screw, coved spacers, cam REPLACING THE HIGH MOUNT and locknut that secure the EXISTING cam to the WHEEL LOCKS (FIGURE 6) caster headtube. NOTE: When using the 24-inch rear wheels the high mount 3.
PROCEDURE 6 PATRIOT 2. Secure the NEW rear arm socket to the wheelchair This Procedure Includes the Following: frame with the locknut. Removing/Installing Rear Arm Socket 3. Install the armrest onto the wheelchair. Refer to RE- Replacing Armrest Bracket MOVING/INSTALLING FLIP BACK ARMREST in Converting from Space Saver to Conventional OR PROCEDURE 4 of the Owner's Manual, part num- Conventional to Space Saver...
PROCEDURE 6 PATRIOT STEPS 2-4 Wheelchair Frame 9. Install the armrest onto the wheelchair. Refer to RE- MOVING/INSTALLING FLIP BACK ARMREST in PROCEDURE 4 of the Owner's Manual, part num- ber 1088909. 10. Repeat STEPS 4-9 for opposite side. Permanent Washer STEPS 2-3 Wheelchair Frame...
PATRIOT PROCEDURE 6 Installing CHANGING SEAT-TO-FLOOR HEIGHT/SEAT-TO-FLOOR ANGLE 1. Position the NEW/EXISTING axle bracket onto the wheelchair frame. WARNING 2. Secure the NEW/EXISTING axle bracket to the DO NOT deviate from the charts on the following pages. There are restrictions for wheelchair frame with the EXISTING mounting screws and locknuts as shown in FIGURE 6.
Page 20
PROCEDURE 6 PATRIOT Caster Headtube, Front Caster, Axle Mounting Bracket Positioning and Cam Position for 24-inch Rear Wheels and 8-inch Front Casters (FIGURES 1 - 7) *WARNING If changing the seat-to-floor angle to 6 , anti-tippers MUST be installed. Refer to the following chart to determine the obtainable seat-to-floor height and seat angle combina- tions for 24-inch rear wheels and 8-inch front casters: SEAT-TO-FLOOR SEAT ANGLE...
Page 21
PATRIOT PROCEDURE 6 *WARNING If changing the seat-to-floor angle to 6 , anti-tippers MUST be installed. AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER CAM POSITION FORWARD REARWARD (STANDARD) (AMPUTEE) LEADING TRAILING Notch FIGURE 4 - SEAT-TO-FLOOR HEIGHT OF 18-1/2-INCHES AND A SEAT ANGLE OF 3 AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER...
Page 22
PROCEDURE 6 PATRIOT Caster Headtube, Front Caster, Axle Mounting Bracket Positioning and Cam Position for 22-inch Rear Wheels and 8-inch Front Casters (FIGURES 1 - 6) *WARNING If changing the seat-to-floor angle to 6 , anti-tippers MUST be installed. Refer to the following chart to determine the obtainable seat-to-floor height and seat angle combina- tions for 22-inch rear wheels and 8-inch front casters: SEAT-TO-FLOOR SEAT ANGLE...
Page 23
PATRIOT PROCEDURE 6 *WARNING If changing the seat-to-floor angle to 6 , anti-tippers MUST be installed. AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER CAM POSITION FORWARD REARWARD (STANDARD) (AMPUTEE) LEADING TRAILING Notch FIGURE 4 - SEAT-TO-FLOOR HEIGHT OF 17-1/2-INCHES AND A SEAT ANGLE OF 0 AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER...
Page 24
PROCEDURE 6 PATRIOT Caster Headtube, Front Caster, Axle Mounting Bracket Positioning and Cam Position for 20-inch Rear Wheels and 8-inch Front Casters (FIGURES 1-3) *WARNING If changing the seat-to-floor angle to 6 , anti-tippers MUST be installed. Refer to the following chart to determine the obtainable seat-to-floor height and seat angle combina- tions for 20-inch rear wheels and 8-inch front casters: SEAT-TO-FLOOR SEAT ANGLE...
Page 25
PATRIOT PROCEDURE 6 Caster Headtube, Front Caster, Axle Mounting Bracket Positioning and Cam Position for 24-inch Rear Wheels and 6-inch Front Casters (FIGURES 1-3) *WARNING If changing the seat-to-floor angle to 6 , anti-tippers MUST be installed. Refer to the following chart to determine the obtainable seat-to-floor height and seat angle combina- tions for 24-inch rear wheels and 6-inch front casters: SEAT-TO-FLOOR SEAT ANGLE...
Page 26
PROCEDURE 6 PATRIOT Caster Headtube, Front Caster, Axle Mounting Bracket Positioning and Cam Position for 22-inch Rear Wheels and 6-inch Front Casters (FIGURES 1 - 8) *WARNING If changing the seat-to-floor angle to 6 , anti-tippers MUST be installed. Refer to the following chart to determine the obtainable seat-to-floor height and seat angle combina- tions for 22-inch rear wheels and 6-inch front casters: SEAT-TO-FLOOR SEAT ANGLE...
Page 27
PATRIOT PROCEDURE 6 *WARNING If changing the seat-to-floor angle to 6 , anti-tippers MUST be installed. AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER CAM POSITION FORWARD REARWARD (STANDARD) (AMPUTEE) LEADING TRAILING Notch FIGURE 4 - SEAT-TO-FLOOR HEIGHT OF 16-1/2-INCHES AND A SEAT ANGLE OF 0 AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER...
Page 28
PROCEDURE 6 PATRIOT AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER CAM POSITION FORWARD REARWARD (STANDARD) (AMPUTEE) LEADING TRAILING Notch FIGURE 8 - SEAT-TO-FLOOR HEIGHT OF 15-1/2-INCHES AND A SEAT ANGLE OF 3 Caster Headtube, Front Caster, Axle Mounting Bracket Positioning and Cam Position for 20-inch Rear Wheels and 6-inch Front Casters (FIGURES 1 - 8) *WARNING If changing the seat-to-floor angle to 6...
Page 29
PATRIOT PROCEDURE 6 *WARNING If changing the seat-to-floor angle to 6 , anti-tippers MUST be installed. AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER CAM POSITION FORWARD REARWARD (STANDARD) (AMPUTEE) LEADING TRAILING Notch FIGURE 3 - SEAT-TO-FLOOR HEIGHT OF 16-1/2-INCHES AND A SEAT ANGLE OF 0 AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER...
Page 30
PROCEDURE 6 PATRIOT *WARNING If changing the seat-to-floor angle to 6 , anti-tippers MUST be installed. AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER CAM POSITION FORWARD REARWARD (STANDARD) (AMPUTEE) LEADING TRAILING Notch FIGURE 7 - SEAT-TO-FLOOR HEIGHT OF 15-1/2-INCHES AND A SEAT ANGLE OF 3 AXLE MOUNTING BRACKET CASTER HEADTUBE FRONT CASTER...
PATRIOT SL PROCEDURE 7 CONVERTING FROM STANDARD This Procedure Includes the Following: AXLE TO AMPUTEE (FIGURE 2) Replacing Armrest Converting from Standard to Amputee WARNING BEFORE performing this procedure, refer to Changing Seat-to-Floor Height SPECIFIC WARNINGS - STABILITY in PROCEDURE 1 of this manual for additional requirements.
PROCEDURE 7 PATRIOT SL SEAT- BRACKET AXLE SPACER SIDE OF AXLE MOUNTING TO-FLOOR POSITION WHEELCHAIR POSITION (on bracket) (on wheelchair) ADULT DOWN RIGHT ADULT DOWN LEFT HEMI RIGHT BOTTOM HEMI LEFT BOTTOM K "A" and "B" are stamped on the sides of the amputee bracket. BRACKET "B"...
Page 33
PATRIOT SL PROCEDURE 7 Caster Headtube, Front Caster, Axle Mounting Bracket Positioning and Cam Position for 24-inch Rear Wheels and 8-inch Front Casters (FIGURES 1 - 2) Refer to the following chart to determine the obtainable seat-to-floor height and seat angle combina- tions for 24-inch rear wheels and 8-inch front casters: SEAT-TO-FLOOR SEAT ANGLE...
Page 34
PROCEDURE 7 PATRIOT SL Caster Headtube, Front Caster, Axle Mounting Bracket Positioning and Cam Position for 20-inch Rear Wheels and 8-inch Front Casters (FIGURE 1) Refer to the following chart to determine the obtainable seat-to-floor height and seat angle combina- tions for 20-inch rear wheels and 8-inch front casters: SEAT-TO-FLOOR SEAT ANGLE...
Page 35
PATRIOT SL PROCEDURE 7 Caster Headtube, Front Caster, Axle Mounting Bracket Positioning and Cam Position for 22-inch Rear Wheels and 6-inch Front Casters (FIGURE 1) Refer to the following chart to determine the obtainable seat-to-floor height and seat angle combina- tions for 22-inch rear wheels and 6-inch front casters: SEAT-TO-FLOOR SEAT ANGLE...
This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state. Invacare warrants its product to be free from defects in materials and workmanship for a period of one (1) year from date of purchase. The side frames and crossmembers are warranted for the lifetime of the original purchaser/users.
Page 37
TABLE DES MATIÈRES TABLE DES MATIÈRES IMPORTANT ............................38 SPÉCIFICATIONS ..........................39 PROCÉDURE 1 - CONSIGNES GÉNÉRALES ..................40 INFORMATION RELATIVE À L'UTILISATION ..................40 PROCÉDURE 2 - ASSEMBLAGE ......................42 ASSEMBLER LE FAUTEUIL ROULANT ....................42 PROCÉDURE 3 - APPUIE-BRAS ......................43 ENLEVER/INSTALLER LES ENCASTREMENTS AVANT DES APPUIE-BRAS/GUIDE DU SIÈGE ..
Invacare recommande de transférer les utilisateurs de fauteuil roulant sur les sièges du véhicule et de les attacher avec les ceintures de sécurité du véhicule. Invacare ne peut et ne veut recommander aucun système de transport de fauteuil roulant.
SPÉCIFICATIONS SPÉCIFICATIONS PATRIOT/PATRIOT SL Largeur totale: 21-1/2 , 23-1/2 - 25-1/2, 27-1/2-po. É Profondeurtotale (Avec équipements avant): 43 ou 45-po. Largeur du siège: 14, 16, 17, 18, ou 20-po. Profondeur du siège: 16 ou 18-po. Distance siège/sol (ADULT/HEMI): 15-1/2 à 19-1/2-po.- en incrément d'un (1) po. Type de dossier: Réglable en incrément d'un (1) po.
Si ces exigences NE PEUVENT être atteintes, NE PAS utiliser le fauteuil roulant. Contacter un fournisseur Invacare ou un technicien qualifié. Tout changement de l'angle siège/sol ou de la distance siège/sol peut nécessiter un type différent d'antibascules.
Page 41
Bien que les antibascules soient optionnels sur les fauteuils 0 ou 3 (vous pouvez les commander avec ou sans les antibascules), Invacare recommande fortement de com- mander les antibascules pour plus de sécurité pour l'utilisateur. Angle siège/sol 6 : Si vous changez l'angle siège/sol à 6 , des antibascules DOIVENT être commandés et installés.
PROCÉDURE 2 ASSEMBLAGE 5. Si nécessaire, convertir l'essieu standard en essieu pour Cette procédure comprend: amputé. Se référer à CONVERTIR L'ESSIEU STAN- Assembler le fauteuil roulant DARD EN ESSIEU POUR AMPUTÉ pour le Patriot dans la PROCÉDURE 6 ou CONVERTIR D'UN ASSEMBLER LE FAUTEUIL ESSIEU STANDARD À...
APPUIE-BRAS PROCÉDURE 3 Installer Cette procédure comprend : 1. Installer le nouvel encastrement avant de l'appuie- Enlever/installer les encastrement avant des appuie-bras/guide du siège bras/guide de siège tel qu'illustré à la FIGURE 1. 2. Installer la vis de montage EXISTANTE dans l'encastrement avant de l'appuie-bras/guide de siège.
PROCÉDURE 4 SIÈGE/DOSSIER RÉGLER/REMPLACER LES Cette procédure comprend: MONTANTS DU DOSSIER Remplacer les guides de siège arrière Régler/remplacer les montants du dossier AVERTISSEMENT AVANT d'exécuter cette procédure, se Remplacer le bloc secteur È référer AUX AVERTISSEMENTS SPÉCIFIQUES - Régler la largeur du siège STABILITÉ...
SIÈGE/DOSSIER PROCÉDURE 4 Remplacer (FIGURES 2 et 3) PATRIOT (FIGURE 3). 1. Enlever la (1) vis de montage et l'écrou de blocage 1. Couper les serre-fils qui fixent la garniture de dossier qui fixent le montant du dossier au fauteuil. EXISTANTE au châssis du fauteuil.
PROCÉDURE 4 SIÈGE/DOSSIER NOUVEAUX croisillons. Se référer au SCHÉMA "A". Châssis du Tige de fauteuil 6. Enlever la vis de montage, les rondelles bombées, blocage les rondelles et l'écrou de blocage qui fixent les deux Rondelle (2) croisillons ensemble. 7. Assembler les deux (2) NOUVEAUX croisillons avec È...
Page 47
SIÈGE/DOSSIER PROCÉDURE 4 Croisillons Vis de montage (ÉTAPES (ÉTAPES 3,9) 3,5,6,7,9,10) Écrou de Châssis du blocage Vis de montage fauteuil (ÉTAPES 3,9) È (ÉTAPES 3,9) Écrou de Lien pivot blocage (ÉTAPES 3,8,9) Étrier du (ÉTAPES 3,9) croisillon (ÉTAPES 4,10) Vis de montage (ÉTAPES 3,9) Écrou de Vis de montage...
PROCÉDURE 5 ROUES 4. Insérer le NOUVEL ensemble fourche/roue avant six Cette procédure comprend: ou huit pouces dans l'encastrement de la roue avant. Enlever/installer les roues arrière 5. Fixer le NOUVEL ensemble fourche/roue avant de Remplacer l'ensemble fourche/roue avant de six ou huit pouces avec l'écrou de blocage EXISTANT.
ROUES PROCÉDURE 5 CHANGER LA POSITION DES Antérieure à postérieure (FIGURE 4) ROUES AVANT DE POSTÉRIEURE 1. Enlever les deux (2) vis de montage, les quatre (4) intercalaires bombés, la rondelle, la came et les deux À ANTÉRIEURE ET D'ANTÉRIEURE (2) écrous de blocage qui fixent l'encastrement de la À...
PROCÉDURE 5 ROUES 2. Enlever la vis de montage, les intercalaires bombés, la REMPLACER LES DISPOSITIFS DE came et l'écrou de blocage qui fixent la came BLOCAGE SURÉLEVÉS DES EXISTANTE à l'encastrement de la roue avant. ROUES (FIGURE 6) 3. Desserrer la vis de montage inférieure, les intercalaires bombés et les écrous de blocage qui fixent NOTE: Lorsque vous utilisez des roues de 24 po., le l'encastrement de la roue avant sur le châssis du fauteuil.
PATRIOT PROCÉDURE 6 2. Fixer le NOUVEL encastrement arrière de l'appuie- Cette procédure comprend: bras sur le châssis du fauteuil avec l'écrou de blocage. Enlever/installer l'encastrement arrière de l'appuie-bras 3. Installer l'appuie-bras sur le fauteuil. Se référer à la Remplacer le support de l'appuie-bras ENLEVER/INSTALLER L'APPUIE-BRAS Changer de écono-espace à...
PROCÉDURE 6 PATRIOT Châssis du Châssis du fauteuil Supports de Écrou de fauteuil l'appuie-bras blocage Vis de Rondelle montage Vis de Écrou de montage blocage Encastrement Rondelle arrière de l'appuie-bras FIGURE 3 - REMPLACER LE SUPPORT DE FIGURE 2 - ENLEVER/INSTALLER L'APPUIE-BRAS L'ENCASTREMENT ARRIÈRE DE L'APPUIE-BRAS -ÉCONO-ESPACE...
PATRIOT PROCÉDURE 6 Châssis du fauteuil 9. Installer l'appuie-bras sur le fauteuil. Se référer à ENLEVER/INSTALLER L'APPUIE-BRAS ÉTAPES 2-4 RABATTABLE de la PROCÉDURE 4 du manuel de l'utilisateur, numéro de pièce 1088909. 10. Répéter les ÉTAPES 4-9 pour l'autre côté. Essieu Rondelle ÉTAPES 2-3...
PROCÉDURE 6 PATRIOT Installer CHANGER LA DISTANCE/ANGLE 1. Placer le NOUVEAU support de l'essieu ou le sup- SIÈGE/SOL port EXISTANT sur le châssis du fauteuil. AVERTISSEMENTS 2. Fixer le NOUVEAU support de l'essieu ou le support RESPECTER les données des tableaux EXISTANT sur le châssis du fauteuil avec les vis de suivants.
Page 55
PATRIOT PROCÉDURE 6 Encastrement des roues avant, roues avant, position du support de montage de l'essieu et position de la came pour roues arrière de 24po. et roues avant de 8po. (FIGURES 1 - 7) *AVERTISSEMENT Si vous changez l'angle siège/sol à 6 , des antibascules DOIVENT être installés.
Page 56
PROCÉDURE 6 PATRIOT *AVERTISSEMENT Si vous changez l'angle siège/sol à 6 , des antibascules DOIVENT être installés. SUPPORT DE MONTAGE DE ENCASTREMENT DE ROUE AVANT POSITION L'ESSIEU ROUE AVANT DE LA CAME AVANT ARRIÈRE ANTÉRIEURE POSTÉRIEURE (STANDARD) (AMPUTE) Encoche FIGURE 4 - DISTANCE SIÈGE/SOL DE 18-1/2 POUCES ET ANGLE DU SIÈGE DE 3 SUPPORT DE MONTAGE DE ENCASTREMENT DE ROUE AVANT...
Page 57
PATRIOT PROCÉDURE 6 Encastrement des roues avant, roues avant, position du support de montage de l'essieu et position de la came pour roues arrière de 22po. et roues avant de 8po. (FIGURES 1 - 6) *AVERTISSEMENT Si vous changez l'angle siège/sol à 6 , des antibascules DOIVENT être installés.
Page 58
PROCÉDURE 6 PATRIOT *AVERTISSEMENT Si vous changez l'angle siège/sol à 6 , des antibascules DOIVENT être installés. SUPPORT DE MONTAGE DE ENCASTREMENT DE ROUE AVANT POSITION L'ESSIEU ROUE AVANT DE LA CAME AVANT ARRIÈRE ANTÉRIEURE POSTÉRIEURE (STANDARD) (AMPUTE) Encoche FIGURE 4 - DISTANCE SIÈGE/SOL DE 17-1/2 POUCES ET ANGLE DU SIÈGE DE 0 SUPPORT DE MONTAGE DE ENCASTREMENT DE ROUE AVANT...
Page 59
PROCÉDURE 6 PATRIOT Encastrement des roues avant, roues avant, position du support de montage de l'essieu et position de la came pour roues arrière de 20po. et roues avant de 8po. (FIGURES 1 - 3) *AVERTISSEMENT Si vous changez l'angle siège/sol à 6 , des antibascules DOIVENT être installés.
Page 60
PROCÉDURE 6 PATRIOT Encastrement des roues avant, roues avant, position du support de montage de l'essieu et position de la came pour roues arrière de 24po. et roues avant de 6po. (FIGURES 1 - 3) *AVERTISSEMENT Si vous changez l'angle siège/sol à 6 , des antibascules DOIVENT être installés.
Page 61
PATRIOT PROCÉDURE 6 Encastrement des roues avant, roues avant, position du support de montage de l'essieu et position de la came pour roues arrière de 22po. et roues avant de 6po. (FIGURES 1 - 8) *AVERTISSEMENT Si vous changez l'angle siège/sol à 6 , des antibascules DOIVENT être installés.
Page 62
PROCÉDURE 6 PATRIOT *AVERTISSEMENT Si vous changez l'angle siège/sol à 6 , des antibascules DOIVENT être installés. SUPPORT DE MONTAGE DE ENCASTREMENT DE ROUE AVANT POSITION L'ESSIEU ROUE AVANT DE LA CAME AVANT ARRIÈRE ANTÉRIEURE POSTÉRIEURE (STANDARD) (AMPUTE) Encoche FIGURE 4 - DISTANCE SIÈGE/SOL DE 16-1/2 POUCES ET ANGLE DU SIÈGE DE 0 SUPPORT DE MONTAGE DE ENCASTREMENT DE ROUE AVANT...
Page 63
PATRIOT PROCÉDURE 6 SUPPORT DE MONTAGE DE ENCASTREMENT DE ROUE AVANT POSITION L'ESSIEU ROUE AVANT DE LA CAME AVANT ARRIÈRE ANTÉRIEURE POSTÉRIEURE (STANDARD) (AMPUTE) Encoche FIGURE 8 - DISTANCE SIÈGE/SOL DE 15-1/2 POUCES ET ANGLE DU SIÈGE DE 3 Encastrement des roues avant, roues avant, position du support de montage de l'essieu et position de la came pour roues arrière de 20po.
Page 64
PROCÉDURE 6 PATRIOT *AVERTISSEMENT Si vous changez l'angle siège/sol à 6 , des antibascules DOIVENT être installés. SUPPORT DE MONTAGE DE ENCASTREMENT DE ROUE AVANT POSITION L'ESSIEU ROUE AVANT DE LA CAME AVANT ARRIÈRE ANTÉRIEURE POSTÉRIEURE (STANDARD) (AMPUTE) Encoche FIGURE 3 - DISTANCE SIÈGE/SOL DE 16-1/2 POUCES ET ANGLE DU SIÈGE DE 0 SUPPORT DE MONTAGE DE ENCASTREMENT DE ROUE AVANT...
Page 65
PATRIOT PROCÉDURE 6 Encastr *AVERTISSEMENT ement des roues a Si vous changez l'angle siège/sol à 6 , des antibascules DOIVENT être installés. SUPPORT DE MONTAGE DE ENCASTREMENT DE ROUE AVANT POSITION L'ESSIEU ROUE AVANT DE LA CAME AVANT ARRIÈRE ANTÉRIEURE POSTÉRIEURE (STANDARD) (AMPUTE) Encoche...
PROCÉDURE 7 PATRIOT SL CONVERTIR L'ESSIEU STANDARD Cette procédure comprend: EN ESSIEU POUR AMPUTÉ Remplacer les appuie-bras (FIGURE 2) Changer de standard à amputé AVERTISSEMENT Changer la distance siège/sol AVANT d'exécuter cette procédure, se référer aux AVERTISSEMENTS -STABILITÉ de AVERTISSEMENT la PROCÉDURE 1 de ce manuel pour les Après TOUT réglage, réparation ou entretien,et exigences.
PATRIOT SL PROCÉDURE 7 5SUPPORT SIÈGE/- POSITION DE COTÉ DU POSITION DE MONTAGE INTERCALAIRE FAUTEUIL DE L'ESSIEU (sur le support) (sur le fauteuil) ADULTE DROIT HAUT ADULTE GAUCHE HAUT HEMI HAUT DROIT HEMI HAUT GAUCHE K "A" et "B" sont inscrits sur les côtés du support pour amputé SUPPORT "B"...
Page 68
PROCEDURE 7 PATRIOT SL Encastrement des roues avant, roues avant, position du support de montage de l'essieu et position de la came pour roues arrière de 24po. et roues avant de 8po. (FIGURES 1 - 2) Se référer au tableau ci-dessous pour déterminer les combinaisons possibles distance siège/sol et angle du siège pour des roues arrière de 24po.
Page 69
PATRIOT SL PROCÉDURE 7 Encastrement des roues avant, roues avant, position du support de montage de l'essieu et position de la came pour roues arrière de 24po. et roues avant de 8po. (FIGURE 1 ) Se référer au tableau ci-dessous pour déterminer les combinaisons possibles distance siège/sol et angle du siège pour des roues arrière de 20po.
Page 70
PROCÉDURE 7 PATRIOT SL Encastrement des roues avant, roues avant, position du support de montage de l'essieu et position de la came pour roues arrière de 22po. et roues avant de 6po. (FIGURE 1 ) Se référer au tableau ci-dessous pour déterminer les combinaisons possibles distance siège/sol et angle du siège pour des roues arrière de 22-po.
É Pour le service, contacter le fournisseur qui vous a vendu le produit Invacare. Si vous n'obtenez pas un service satisfaisant, écrire directement à INVACARE à l'adresse indiquée ci-dessous. Fournir le nom du fournisseur, l'adresse, le numéro de modèle et la date d'achat, indiquer la nature du problème et, si le produit comporte un numéro de série,...