Operating Sequence - Zanussi ZDT 6894 Instruction Book

Operating sequence

1. Check the filters
Ensure they are clean and properly positioned (see
"Maintenance and cleaning").
2. Press the On/Off push button
The display will show the last selected programme.
3. Check that there is rinse aid and salt
The corresponding indicator lights will illuminate if
refilling is necessary.
4. Load the dishes
Remove any scraps of food.
Pull the lower basket out and arrange the saucepans,
plates and cutlery in it.
Pull the upper basket out and arrange the plates,
saucers, glasses and cups etc. in it.
Slide the baskets back into the machine.
5. Ensure that the spray arms can
rotate freely
6. Measure out detergent
Add the required amount of detergent into the dispenser.
Important!
If you select the half load option remember to reduce
the quantity of detergent.
Close the detergent dispenser lid.
7a. Setting and starting the programme
without "Delay start"
The selection of the programme occurs with the door
partially opened.
Press the "programme selection" push button until the
required programme number appears in the digital
display.
If you wish to see the duration of the programme you
have just selected, ONLY with the door opened, press
the Cancel push button.
Select a drying option and/or half load (if desired).
Close the door, the programme will start automatically
and an audible signal advises you of that.
The display will show the running time of the
programme.
7b. Setting and starting the programme
with "Delay start"
Once a programme and required options (see point 7a)
have been selected to use Delay start proceed as
follows:
Press the Delay start push button. The digital display
will show "h 0". Press the button again to select the
number of hours by which you wish to delay the
programme start (up to a maximum of 12 hours).
If the a drying option and/or half load have been
selected the corresponding indicator lights will turn off,
but don't worry, the delay start will not modify the
settings made previously .
To set the time setting to zero press the Delay start
push button until "h 0" appears in the digital display.
Close the door, the countdown will start automatically
and an audible signal advises you of that.
The start of the programme is shown in the digital
display and will decrease from hour to hour.
The progression of the countdown will be confirmed by a
flashing dot after the number in the digital display.
The opening of the door will not stop the countdown.
Once the delayed time has elapsed the programme will
start automatically and in the digital display will appear
the duration of the programme.
To cancel a delay start in progress, open the door and
press the Cancel push button. The delay start will be
cancelled without modifying the previous selection of the
washing programme with relative options. In the digital
display will appear the number of the programme.
8. To cancel a programme in progress
Open the door and press the Cancel push button.
An audible signal will inform you that the programme has
been cancelled and in the digital display first will appear
three horizontal lines --- (for about 2 seconds) and then
the number of the programme just cancelled.
The dishwasher has returned to setting mode and it is
now possible to select a new washing programme.
9. At the end of the washing
programme
The dishwasher will automatically stop and an
intermittent audible signal will be heard when the
programme has ended (when the delay start has been
selected the audible signal "end of programme" is
automatically excluded).
3 flashing horizontal lines will appear in the digital
display and all the indicator lights will turn off.
Open the door and press the On/Off push button.
Wait a few minutes before removing the dishes; in this
way they will be cooler and the drying will be improved.
Empty the lower basket first and then the upper one; this
will avoid water dripping from the upper basket onto the
dishes in the lower one.
Important!
In general it is not advisable to open the door while the
machine is working; if the door is opened however, a
safety device ensures that the machine stops.
Care must be taken if the door is opened during the hot
phase or immediately after a programme has finished, as
steam may escape.
When the washing programme has finished, it is
recommended that the dishwasher is unplugged and the
water tap turned off.
11