Threshold Calculation Given Amplifier Gain ................... 16 7. SOFTWARE AVAILABILITY ..........................17 7.1. Direct from Factory ............................17 7.2. Download from the INTERNET ........................17 7.3. Bundled with New Merlin ISP-100 ........................ 17 INSTALLATION ..............................17 8.1. Loading the Software ............................ 17 OPERATION ................................ 17 10.
HF horn and vented- signal routing, and speaker excursion protection, box direct-radiator low end. Rated frequency among others. The Merlin ISP-100 is controlled by response of 50 to 20,000 Hz. an attached PC connected to the ISP-100 through a serial connection.
CONFIGURATIONS: A METHOD TO system and the crossover used to drive it. The INCREASE DIRECTIVITY Merlin ISP-100 provides processing that allows the 3.1. Description vertical coverage of the systems to be narrowed in the upper bass and lower midrange (see the...
Merlin X-Array Install Manual = HORIZONTAL = VERTICAL 2. Correspondingly, an increase in directivity ranging from 0.5 to 2.5 dB is noted over the same FIGURE 1 - range for the overlap condition. 3.2.2. Xi-2153/64 and Xi-2183/64 Normal Three- way vs Overlap (Tripole) Three-way Operation Figure 3 shows the beamwidth and directivity of the dual-woofer three-way systems operating in the...
In addition, all high-frequency A 0- to 650-ms delay and a five-band filter set are located before the crossover. This filter set is used FIGURE 5 - 2-Way Quick Map Electro-Voice X-Array Install Merlin ISP-100 2-Way Quick Map LOW OUT...
Merlin X-Array Install Manual for two purposes. The first is to provide a high-pass which may function as a subsonic filter or a filter for the low-frequency woofer in the full-range crossover filter when used with subwoofers, and to system - which may function as a subsonic filter or provide equalization filters for tuning the a crossover filter when used with subwoofers.
QuickMAPs have been assigned to module #1 of the ISP-100. Where possible, the remaining outputs All outputs of the two-way QuickMAP have a latent follow the Merlin ISP-100 convention of assigning delay of 10 sample periods (about 208 us). outputs in low- to high-frequency order, high- to Unavoidably however, the three-way QuickMAP has low-number module order, and letter “a”...
Merlin X-Array Install Manual Both sub-channel outputs have been assigned to Although subwoofer-woofer overlap naming the same output module in each of the two capability is included, QuickSETs for this operation QuickMAPs (module #4 for the two-way QuickMAP are reserved for future release, and are not and module #2 for the three-way).
Merlin X-Array Install Manual turned off then back on.) Therefore, any 2. Increase the high-frequency digital gain in the adjustments made to the analog gain structure to “Filters” menu by +8 dB. From the Vue-It improve the signal-to-noise ratio must be program, click on the “Filters”...
Merlin X-Array Install Manual EXCURSION PROTECTION BLOCK DIAGRAM LOOK-AHEAD INPUT OUTPUT LIMITER DELA Y EXCURSION FILTER SIDE CHAIN 4. Set the mid-bass-frequency analog output gains the power amplifier gain must be known in order to to –8 dB. From the Vue-It program, click on any set the threshold levels of the protection limiters.
The values may be determined by loading a specific through any feedback scheme. Thus the gain system’s Project into the VUE-IT program and then structure from the Merlin ISP-100 through to the single-clicking on a specific limiter. power amplifiers is extremely important for proper CAUTION: The factory supplied limiter thresholds limiter protection operation.
Merlin X-Array Install Manual TABLE - LIMITER THRESHOLD SETTINGS DIRECTIONS: 1. Set power amplifier gain to desired setting. 2. Apply sinewave signal of 0.100 V rms (100 mV) at 400 Hz to amplifier input. 3. Measure amplifier output voltage. 4. Lookup new threshold in table: a.
7. SOFTWARE AVAILABILITY of the measured output voltage and the The X-Array Install Merlin ISP-100 setup software recommended threshold. and manual is available three different ways: 1. 6.4.2. Threshold Calculation Given Amplifier Gain direct from the factory, 2.
Vue-It program may be typically found in the The manual and software are included with each following directory: C:\PROGRAM FILES\VUE- new Merlin ISP-100. To place an order for a new IT\ISP-100\. Double click on the Vue-IT icon to start Merlin ISP-100 contact your local authorized Merlin the program.