Windows is a registered trademark of Microsoft Corporation. Optiquest, OnView, ViewMeter, and ViewMatch are registered trademarks, and Optimize Your Image is a trademark of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association (VESA). DPMS is a trademark of VESA.
Page 3
If you have any questions concerning which proper power cord to use, please consult with the dealer from whom you purchased your monitor. Table A Cord Type Size of Conductors In Cord Maximum Current Rating of Unit 18AWG 10Amps 16AWG 12Amps 14AWG 12Amps 18AWG 10Amps 17AWG 12Amps Optiquest Q55...
To assure continued CE compliance the user must use the provided 1.8m shielded video signal cable with bonded ferrite cores at both ends of the cable. Handle correctly in accordance with the instruction manual. *EMI : Electromagnetic Interference *ESD : Electrostatic Discharge *RF : Radio Frequency *F/B : Fast Burst Optiquest Q55...
Customer Support ........back cover *To meet your future needs, and to receive any additional product information as it becomes available, please register your monitor's warranty on the Internet at: http://www.optiquest.com. Getting Started Optiquest Q55...
® Microsoft operating systems: Windows '95, Windows '98, Windows NT (5.0). Package Contents Your Optiquest Q55 package includes the following: • Optiquest Q55 monitor with attached video cable (15 pin mini D-sub connector) • Power cord • User’s guide •...
Connect a Resolution Right-click on the Windows Macintosh adapter (part No. GMAC-1) desktop > Properties > Settings > to the video cable, then to the Q55. To "Desktop Area." Set the resolution. ® order an adapter, contact ViewSonic Refresh Rate (vertical frequency) (see the back cover of this guide).
* The monitor automatically degausses each time you turn it on. Degaussing removes magnetic field buildup that can affect color purity and convergence. Do not turn the monitor off, then immediately on again repeatedly. Wait 20 minutes before turning the monitor on again to prevent possible damage. Operation Optiquest Q55...
TILT rotates the entire screen [>] Increases the width image. [<] Rotates the screen counter- clockwise VERTICAL POSITION moves the [>] Rotates the screen clockwise screen up and down. [<] Moves the screen down [>] Moves the screen up Operation Optiquest Q55...
Page 10
USER's modes by pressing the Note: The monitor automatically [<] or the [>] button. These lists degausses when you turn it on. are for viewing only. Wait at least 20 minutes before selecting DEGAUSS from the menu to prevent possible damage. Operation Optiquest Q55...
See the back cover. You will need to provide your monitor's serial number. Warning: Do not set the graphics card in your computer to exceed these maximum refresh rates. Doing so may result in permanent damage to the monitor. NI = Non Interlaced. Other Information Optiquest Q55...
Make sure video input signals are within the monitor's specified frequency range. • Try the monitor with another power source, graphics card, or computer system. • Connect the video cable securely. Control buttons do not work • Press only one button at a time. Optiquest Q55 Other Information...
Some chemical cleaners have been reported to damage the screen and/or case of the monitor. Optiquest will not be liable for damage resulting from use of any ammonia or alcohol-based cleaners. Other Information Optiquest Q55...
If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
Customer Service To receive the most prompt assistance, dial the appropriate number below and listen to all menu options before making your selection: Customer Support, Technical Support, Parts, etc. U.S. and Canada only 1-800-843-6784 From outside U.S. and Canada 909-869-9216 From Europe +44 (1293) 643-900 From Asian/Pacific Rim countries...