JVC GZ-MC200US Service Manual page 22

3.2.2 ASSEMBLY/DISASSEMBLY OF CABINET PARTS AND ELECTRICAL PARTS
Disassembly procedure
STEP Fig.
PART NAME
No. No.
[1]
GRIP LOWER ASSY FA1
[2]
COVER(FR.) ASSY FA2
[1]
GRIP LOWER ASSY FA3
[3]
COVER(TOP) FA4
[4]
REG PWB ASSY FA5-1
FA5-2
FA5-3
[5]
CF ASSY FA6
[6]
PLATE(ROTALY) FA7-1
FA7-2
[7]
MONITOR ASSY FA8
NOTE1a:
When removing, remove the four SCREWS (1-4) first to
avoid damage or deformation of the ARM (COVER) AS-
SEMBLY and the STAY (COVER) ASSEMBLY.
During the procedure, be careful with opening and closing of
the BATTERY/ CF CARD COVER.
Also, be careful not to damage the parts with the ARM
(COVER) ASSEMBLY or the STAY (COVER) ASSEMBLY.
NOTE1b:
Be careful in handling the SPACER.
Attach the SPACER to adjust the edge of CN302.
NOTE1c:
When attaching, be careful not to pinch the WIRE.
Pay special attention on the inside of the TRIPOD and the
BATTERY wiring.
NOTE2a:
When removing the COVER(FR.)ASSEMBLY, remove the
SCREW (No.8) first for the smooth removal of other parts.
NOTE2b:
When removing, be careful not to lose the part (SHAFT).
NOTE4a:
During the procedure, be careful not to damage the CON-
NECTOR or cut/break the WIRE.
NOTE4b:
When removing, be careful in handling the SPACER.
NOTE4c:
Be careful with the wiring and the affixing the SPACER.
NOTE4d:
When attaching, be sure to place the FPC WIRE inside.
NOTE4e:
When attaching, lift the part (ARM) upward.
NOTE4f:
During the procedure, be careful not to deform the part
(ARM) or damage other parts.
NOTE5a:
Peel off the SPACER before removing the WIRE (GREEN)
of CN5b.
NOTE5b:
Be careful with the positions of the SCREWS that are to be
removed.
NOTE5c:
During the procedure, be careful with the grease.
1-22 (No.YF059)
POINT NOTE
2(S1a),2(S1b)
NOTE1a
S2a,S2b,S2c,S2b
NOTE2a,b
L1a, L1b,2(S1c),CN1a,b
NOTE1b,c
S3a,S3b,3(S3a)
-
CN4a,b,2(S4),CN4c,d,e,f,g,h
NOTE4a
-
NOTE4b,c
-
NOTE4d
CN5a,b,2(S5a),S5b
NOTE5a,b,c,d
3(S6)
NOTE6
-
NOTE6
4(S7)
NOTE7
NOTE5d:
When attaching, connect the SPACER to the CONNECTOR
(CN5a, b), and place the SPACER inside by folding it.
NOTE6:
When attaching, be careful with the wiring,
NOTE7:
When removing, turn the CAMERA ASSEMBLY and re-
move the total of four SCREWS, two SCREWS at a time.
Destination of connectors
CN.NO. CONNECTOR
CN1a REG CN305
CN1b REG CN307
CN4a REG CN301
CN4b REG CN302
CN4c REG CN306
CN4d REG CN309
CN4e REG CN303
CN4f REG CN310
CN4g REG CN304
CN4h REG CN308
CN5a CF CN9901
CN5b CF CN9902
PIN
NO.
OPE3 - 6
BATT_TERM - 6
ANALOG CN206 10
ANALOG CN207 27
LCD SUB CN7802 30
CF CN9904 20
ANALOG CN208 30
CF SW - 2
OPE2 - 12
CDS, DIGITAL CN5103,103 11
CF SUB CN9801 27
CF SUB CN9802 27