Insignia NS-1UCDVD User Manual page 7

Insignia NS-1UCDVD DVD Player
2 Plug the audio/video cables from the DVD
player's jacks to the TV as follows:
Connect on player
Cable
to:
S-video S-VIDEO OUT
cable (S)
Video VIDEO OUT
Cable (V)
Audio AUDIO OUT
Cable (A)
Y PB PR COMPONENT/PROGRE
Cable (C) SSIVE SCAN
Note
Connecting both the S-video and component
cables may cause the TV display to be unstable.
To resolve the problem, disconnect one of the
problems.
Connecting your player to an HDMI TV
High Definition Multimedia Interface (HDMI)
supports both video and audio on a single digital
connection for use with DVD players, set-top
boxes, and other AV devices.
HDMI was developed to provide the
technologies of High-bandwidth Digital Content
Protection (HDCP). HDCP is used to protect
both transmitted and received digital content.
HDMI has the capability to support standard,
enhanced or high-definition video plus standard
to multi-channel surround-sound audio. HDMI
features include uncompressed digital video, a
bandwidth of up to 5 gigabytes per second, one
connector (instead of several cables and
connectors), and communication between the
AV source and AV devices such as DTVs.
Note
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI licensing LLC.
To connect your player to an HDMI device:
1 Set the source on your HDMI TV or monitor
to HDMI as instructed in the owner's manual.
2 Connect the HDMI OUT jack on the DVD
player to the HDMI jack on your HDMI TV or
monitor using an HDMI cable (H).
Connect on tv to:
S-VIDEO IN
VIDEO IN
AUDIO IN (left and
right)
Corresponding TV jacks
Setting the resolution
www.insignia-products.com
The arrow on the cable connector body
should face up for correct alignment with the
connector on the player.
3 Press RESOLUTION repeatedly to select the
desired resolution. When you use an HDMI
connection, you can change the resolution
(480i, 480p, 720p, 1080i) for the HDMI
output.
The HDMI output will have a resolution of
480p, even if you set the resolution to 480i on
the HDMI connection.
When no sound or noisy sound result from
the HDMI connection, set the Audio option
[Dolby Digital, DTS or MPEG] on SETUP
menu to PCM or Off.
Notes
If there is noise or lines on the screen, check the
HDMI cable.
Not all HDCP-compatible DVI devices will work
with this player.
If your HDMI TV does not support HDCP, the
screen is blue in color.
If the TV picture is abnormal, turn off the unit and
then turn the unit on again.
Both PCM and Bitstream Audio out is available
when the sample frequency is set to 48kHz in HDMI
connection.
If Audio setup is set to bitstream and your TV does
not support Bitstream Audio out when using an
HDMI
connection, there may be no audio sound or
sound may not be distorted.
If your TV does not accept your resolution
setting, the tv picture displays abnormally. Refer
to the owner's manual for your TV to set the
correct resolution.
To set the resolution:
1 Press the STOP button to stop playback and
put the player in stop mode.
2 Press the RESOLUTION button once. The
current resolution displays in the window.
3 Press the RESOLUTION button repeatedly
to change to the desired resolution. Available
resolutions according to the connections
include:
Output connection Available resolution
HDMI VIDEO OUT
1920 x 1080i
1280 x 720p
720 x 480p
720 x 480i
COMPONENT VIDEO
1920 x 1080i
OUT
1280 x 720p
720 x 480p
720 x 480i
VIDEO OUT 720 x 480i
720 x 480p
S-VIDEO
720 x 480i
7