1. Manuals
  2. Brands
  3. NEC Manuals
  4. Projector
  5. MultiSync MT 600
  6. User manual

NEC MultiSync MT 600 User Manual

Hide thumbs Also See for MultiSync MT 600:
Table of Contents

Advertisement

Quick Links

Download this manual
NEC Multimedia Theatre
R
600
LCD Projector
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for NEC MultiSync MT 600

Summary of Contents for NEC MultiSync MT 600

  • Page 1 NEC Multimedia Theatre LCD Projector User’s Manual...

  • Page 2: Cable Connection

    I N F O R M A T I O N Precautions CAUTION Please read this manual carefully before using your NEC TO PREVENT SHOCK, DO NOT OPEN THE CABI- MultiSync MT600 LCD Projector and keep the manual handy for NET.
  • Page 3 EXCEPT those specified by AN OUTLET UNLESS ALL THREE PRONGS CAN BE NEC Technologies in this manual. Failure to comply with this FULLY INSERTED. DO NOT OPEN THE CABINET. THERE government regulation could void your right to operate this equip- ARE HIGH-VOLTAGE COMPONENTS INSIDE.

  • Page 4: Important Safeguards

    These safety instructions are to ensure the long life of your LCD projector installation must in accordance with any local building codes. and to prevent fire and shock. Please read them carefully and heed all b. The LCD projector must be installed by qualified NEC service warnings. personnel.

  • Page 5: Pc Control Command Reference

    LCD project. If something should fall into your disconnect the plug from the power outlet. projector, disconnect it immediately and have the object removed by a qualified NEC service person. Cleaning 3. Do not place any liquids on top of your LCD projector.
  • Page 6 ATTENTION Ce symbole a pour but de prévenir l’utilisateur RISQUE D’ELECTROCUTIONNE P AS OUVRIR de la présence d’une tension dangereuse, non isolée se trouvant à l’intérieur de l’appareil. Elle est d’une intensité suffisante pour constituer un risque d’électrocution. Eviter le contact avec les pièces à...

  • Page 7: Timing Chart

    Timing Chart Resolution Refresh F.H. Rate (Hz) (kHz) Clk(MHz) NTSC 640 x 480 15.73 640 x 480 512 x 384 60.15 24.48 15.67 512 x 384 60.15 24.48 17.234 640 x 395 20.35 640 x 400 24.83 21.053 640 x 400 31.47 25.175 640 x 480...
  • Page 8 I N T R O D U C T I O N Alimentation 4. La fumée, la vapeur et l’exposition aux rayons directs du soleil risquent de détériorer sérieusement les composantes internes. 1. Le projecteur à écran à cristaux liquides (LCD) est conçu pour 5.
  • Page 9 D-Sub Pin Assignments PC 15-Pin mini D-Sub Macintosh 15-Pin D-Sub Pin No. Signal to be connected Pin No Signal to be connected Red GND Green Blue Horizontal Sync No Connection Green Red GND Green GND Green GND No Connection Blue GND No Connection No Connection Blue...
  • Page 10 2. Any product on which the serial number has been defaced, modified or removed. NEC Technologies, Inc. (hereafter NECTECH) warrants this product to be 3. Damage, deterioration or malfunction resulting from: free from defects in material and workmanship under the following terms.
  • Page 11 EXCLUSION OF DAMAGES NOTE: All products returned to NECTECH for service MUST have NECTECH’S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIM- prior approval. To get approval, call NEC Technologies at ITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT 800-836-0655.

  • Page 12: Table Of Contents

    If “Auto Picture” is off, turn it on. If “Auto RGB mode Picture” is on, turn it off and balance the image with the Picture Adjustment icon and Fine Picture Adjustment icon. To Contact Your NEC Service Representative, Call 1-800-836-0655 TROUBLESHOOTING...

  • Page 13: Specifications

    Common Problems & Solutions Problem Check These Items Does not turn on Check that the cord is plugged in and that the power switch on the back panel is on. Ensure that the air filter and filter panel are installed correctly. (See page 43.) Check the status light to see if the projector has overheated.
  • Page 14 PC or Mac. But best of all, the MultiSync MT600 Projector, provides a list of materials that comes with your projec- is an NEC LCD projector. That means you can depend on years of tor and describes the features and controls.

  • Page 15: Status Light Messages

    Canada. * Installing the MultiSync MT600 LCD Projector on the ceiling PAL: TV standard used in western Europe must be done by authorized NEC technicians. Consult your NEC dealer for more information. SECAM: TV standard used in France and...

  • Page 16: How Do You Get Started

    Please save the original box and packing materials if you ever need to ship your MultiSync MT600 LCD Projector. • NEC MultiSync MT600 LCD Projector • Introductory Video • Remote Control And Cable • User's Manual •...
  • Page 17 Nettoyer et remplacer le filtre Le filtre à air éponge empˆ e che la poussière et la saleté de pénétrer à l’intérieur du projecteur à écran à cristaux liquides (LCD) et devrait ˆ e tre nettoyé après 100 heures d’usage (plus souvant dans les endroits trés poussiéreux). Si le filtre est sale ou bouché, votre projectuer peut surchauffer NOTE: Nettoyer votre filtre après 100 heures d’usage.

  • Page 18: Top Features

    41.) 5. Installer une nouvelle ampoule et fixer le coffret de l’ampoule avec les deux vis. PRECAUTION: Ne pas utiliser d’autres ampoules que l’ampoule NEC en option. Faire la commande avec le numéro de modèle de votre projecteur.

  • Page 19: Terminal Panel Features

    REMPLACER L’AMPOULE Apriès un fonctionnement de 2000 heures ou plus, un signal lumineux s’affichera dans le coffret de l’appareil. Mˆ e me si l’ampoule demeure fonctionnelle, ATTENTION • NE PAS TOUCHER A L’AMPOULE immédiatement après usage. Celle-ci sera extrˆ e mement chaude. Attendre au moins une heure pour laisser l’ampoule refroidir av •...

  • Page 20: Remote Control Battery Installation

    4. Left Channel/Mono Audio Input Jack This is your left channel audio input for stereo sound coming from video equipment or audio system. It also serves as the mono audio input for S-Video input. 5. Right Channel Audio Input Jack This is your right channel audio input for stereo sound. 6.

  • Page 21: Cleaning Or Replacing The Filter

    Cleaning Or Replacing The Filter The air-filter sponge keeps the inside of the MultiSync MT600 LCD Projector free from dust or dirt and should be cleaned after every 100 hours of operation (more often in dusty conditions). If the filter is dirty or clogged, your projector may overheat. NOTE: Clean your filter after every 100 hours of operation.
  • Page 22 5. Install a new lamp case assembly and secure it in place with the two Step 4 screws. CAUTION: Do not use lamps other than the NEC optional lamp. Order by your projection's model number. 6. Reattach the lamp cover and reinstall the single screw.

  • Page 23: Replacing The Lamp

    M A I N T E N A N C E This section describes the simple maintenance procedures you should follow to replace the lamp, clean or replace the filter, and replace the batteries in the remote control. Step 2A Replacing The Lamp After your lamp has been operating for 2000 hours or longer, the “status”...

  • Page 24: Setting Up Your Multisync Mt600 Lcd Projector

    I N S T A L L A T I O N This section describes how to set up your MultiSync MT600 LCD projector and how to connect video and audio sources. Setting Up Your MultiSync MT600 LCD Projector Pull down Your MultiSync MT600 LCD Projector is simple to set up and use.

  • Page 25: Using A Tabletop Or Cart

    Set Position This reorients your image for your type of projection. Press the (+) button until you have the correct image orientation. It moves sequentially: front floor projec- tion - rear ceiling projection - rear floor projection - front ceiling projection. Press the(- ) to move backward through the sequence.

  • Page 26: Ceiling Installation

    Installing your MultiSync MT600 LCD Height 102.36" Projector on the ceiling must be done by a 2600mm qualified technician. Contact your NEC Screen size: 80" dealer for more information. 47.2" h3 h2 h1 Do not attempt to install the projector your- 1200mm self.

  • Page 27: Reflecting The Image

    You can use your MultiSync MT to project an image from the rear onto a transparent screen. The distance the projector must be from the screen is the same as if you were projecting the image from the front. Contact your NEC dealer if you need a transparent screen.

  • Page 28: Wiring Diagram

    Wiring Diagram NOTE: The two D-Sub 15-pin connectors here can be used to either input or output video to or from a PC or Macintosh computer. Either connector can be used for input or output, however they cannot both be used for input simultaneously. It can damage your computer.
  • Page 29 CAUTION Do not unplug the projector while the cooling fan is on. The fan will remain on as long as there is heat inside the LCD projector and the main power switch is Using The Icons 1. Press the “Menu” button on the remote control or projector cabinet to display the icon bar.

  • Page 30: Connecting Your Pc Or Macintosh Computer

    Connecting Your PC Or Macintosh Computer Connecting your PC or Macintosh computer to your MultiSync MT600 LCD Projector will enable you to project your computer’s screen image for an impressive presenta- tion. All of these following display standards are supported: VGA 640 x 480 for graphics,VGA 640 x 400 for graphics,VGA 640 x 350 for graphics,VGA 720 x 400 for text,VGA 720 x 350 for text,Macintosh at 640 x 480 To connect to a PC, Macintosh or computer equipped with a VGA adapter or compat-...

  • Page 31: Connecting Your Document Camera

    O P E R A T I O N This section describes how to select a computer or video source and how to adjust the picture and sound. General Controls Before you turn on your MultiSync MT600 LCD Projector ensure that the computer or video source is turned on and that your lens cap is removed.

  • Page 32: Connecting An External Monitor

    4. Turn on the LCD projector and the computer, document camera or video source. Connecting Your IR Mouse Receiver The IR Receiver enables you to operate your computer’s mouse functions from the NEC MultiSync MT600 remote control. It is a great convenience for clicking through your computer-generated presentations. To connect the IR Receiver: 1.

Table of Contents