Download Print this page

Fujitsu fi-5750 C Instruction Manual

Scanner

Hide thumbs Also See for fi-5750 C:

Operator's manual (167 pages)

,

Getting started (40 pages)

,

Cleaning instructions (2 pages)

Table Of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual

M

I

nstruction

anual

for Fujitsu Scanners

Cleaning and Consumable Replacement Instructions

fi-5750C/fi-5650C

Versitec is a division of Cranel, Inc.

Table of Contents

Advertisement

Summary of Contents for Fujitsu fi-5750 C

Page 1 Fujitsu Scanners Cleaning and Consumable Replacement Instructions fi-5750C/fi-5650C Versitec is a division of Cranel, Inc.
Page 3 INSTRUCTION MANUAL FOR FUJITSU 5750 C/ -5650C CANNER...
Page 4: Table Of Contents
FI -5750 C A N N E R TABLE OF CONTENTS Cleaning the ADF Components ........... Cleaning the Flatbed ............Cleaning the ADF Components ........... Replacing the Brake Rollers ..........Replacing the Pick Rollers ............
Page 5: Cleaning The Adf Components
LEANING AND EPLACING ONSUMABLES Cleaning the Automatic Document Feeder (ADF) Components CAUTION Disconnect the scanner from power outlet CAUTION Allow the glass in the ADF to cool for at least three minutes before cleaning it Press the two blue buttons to open up the ADF compartment Use a clean cloth moistened with V1 cleaner to wipe the entire surface of these components: brake rollers - you may want to open the brake roller...
Page 6 Clean these components with the cloth moistened with V1 cleaner as well: chute roller pick arm feed rollers sheet guide glass ats Clean the plastic rollers with F2 cleaner Gently close the ADF after allowing the ADF components to dry for a few...
Page 7: Cleaning The Flatbed
Cleaning the Flatbed Press on the atbed cover handle and carefully lift up until the cover stays open so that you can access the glass surface. Wipe the glass surface with a clean cloth moistened with V1 cleaner Allow the glass surface to dry for a few minutes Gently close the atbed cover and resume scanner operation Using a Cleaning Sheet to Clean the ADF Components Leave the scanner connected to the power outlet.
Page 8: Replacing The Brake Rollers
Repeat this until the sheet is noticeably dirty. Discard the cleaning sheet EPLACING THE ONSUMABLES Replacing the Brake Rollers Press the two blue buttons to open the ADF Open the brake roller compartment door Lift the brake roller set from the door. Note the orientation of the shiny black roller on the left side of the compartment door.
Page 9: Replacing The Pick Rollers
Install the new brake roller set into the door with the shiny black roller on the left. Close the brake roller compartment door. If you encounter any resistance , r o l l o e l l . y l Close the ADF and resume scanner operation To reset the Brake Roller Counter see your scanner manual or consult with your computer software support department.
Page 10 Open the Pick Roller compartment door using your thumb Slide one pair of pick rollers to the right to remove it from the shaft and replace it with the matching set from your kit. The smoother, smaller, set of rollers are the rst in the paper path, followed by the larger, treaded rollers.
Page 11 www.versitec.com Corporate Headquarters 8999 Gemini Parkway Columbus, OH 43240 Fax: 614.431.8388 Repair Center Western Region Office 908 Boston Turnpike Road 8001 Irvine Center Drive, 4th Floor Shrewsbury, MA 01545 Suites 411, 412, 413 Fax: 508.460.1890 Irvine, CA 92618 For inquiries on consumables, call Versitec at: 888.722.6548...

This manual is also suitable for:

Fi-5650c