Table of Contents
Advertisement
their model at distances farther than a football field (300+ feet). At
greater distances, you could lose sight of your model and you may
also exceed the radio system's operating range, which will cause
the fail-safe system to activate. For best visibility and control of your
model keep your model within 200 feet, regardless of the maximum
range available.
No matter how fast or far you drive your model, always leave
adequate space between you, the model, and others. Never drive
directly toward yourself or others.
TRANSMITTER LED CODES
LED Color / Pattern
Name
Solid green
Normal Driving
Mode
Slow red
Binding
(0.5 sec on / 0.5 sec off)
Flashing medium red
Low Battery
(0.25 sec on / 0.25 sec off)
Alarm
Flashing fast red
Link Failure /
(0.125 sec on / 0.125 sec off)
Error
RECEIVER LED CODES
LED Color / Pattern
Name
Solid green
Normal Driving
Mode
Slow red
Binding
(0.5 sec on / 0.5 sec off)
Flashing fast red
Fail-Safe / Low-
(0.125 sec on / 0.125 sec off)
Voltage Detect
TQ 2.4GHz Binding Instructions
For proper operation, the transmitter and receiver must be electronically
'bound.' This has been done for you at the factory. Should you ever
need to re-bind the system or bind to an additional transmitter or
receiver, follow these instructions. Note: the receiver must be connected
to a 4.8-6.0v (nominal) power source for binding and the transmitter and
receiver must be within 5 feet of each other.
1. Press and hold the SET button on the transmitter.
2. Turn on the transmitter and release the SET button. The status LED will
flash red slowly, indicating that the transmitter is in bind mode.
3. Press and hold the LINK button on the receiver.
4. Turn on the speed control by pressing the EZ-Set button and release
Notes
the LINK button.
See page 13 for information
on how to use the transmitter
5. When the LEDs on both the transmitter and the receiver turn solid
controls.
green, the system is bound and ready for use. Confirm that the
steering and throttle operate properly before driving your model..
See this page for more information
on binding.
SETTING UP THE ANTENNA
Put new batteries in the
The receiver antenna and antenna tube
transmitter. See page 11 for
must be properly installed before operating
more information.
your model. Follow these steps to install the
Transmitter and receiver are no
antenna and antenna tube:
longer bound. Turn the system
off and then back on to resume
1. Slide the antenna wire into the antenna
normal operation. Find source of
tube to its full extent. When fully inserted,
the link failure (i.e., out of range,
the wire should reach to approximately 1/2
low batteries, damaged antenna).
inch below the tube cap. Do not leave any
slack in the antenna wire.
2. Insert the base of the antenna tube into the
Notes
antenna post. Take care not to crimp the
See page 13 for information
antenna wire.
on how to use your transmitter
3. Slide the crimp nut over the antenna tube
controls.
and screw it onto the antenna post.
See this page for more information
4. Use the supplied tool to tighten the crimp
on binding.
nut on the post just until the antenna tube
Consistent low voltage in the
is securely in place. Do not overtighten
receiver triggers Fail Safe so
that there is enough power to
or crush the antenna wire against the
center the throttle servo before it
chassis. Do not bend or kink the antenna
completely loses power.
wire! Do not shorten the antenna tube.
See the sidebar for more information.
TRAXXAS TQ 2.4GHz RADIO SYSTEM
Antenna
Tip
Antenna
Tube
Antenna
Wrench
Antenna
Crimp Nut
Antenna
Post
To prevent loss of radio range,
do not kink or cut the black wire,
do not bend or cut the metal tip,
and do not bend or cut the white
wire at the end of the metal tip.
Correct
No
No
No
No
Fail-Safe
Your Traxxas radio system
is equipped with a built-
in fail-safe function that
returns the throttle to its
last saved neutral position
in the event of a signal loss.
The LED on the transmitter
and the receiver will rapidly
flash red when the fail-
safe mode is activated. If
fail-safe activates while you
are operating your model,
determine the reason for
signal loss and resolve the
problem before operating
your model again.
3
SLASH • 15
Advertisement
Table of Contents
