Related Manuals for Jonsered 2054
Summary of Contents for Jonsered 2054
- Page 1 Operator´s manual Please read these instructions carefully and make sure you understand them before using the saw.
-
Page 2: Key To Symbols
KEY TO SYMBOLS Symbols on the chain saw: CAUTION! Chain saws can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the instructions carefully and make sure you understand them before using the saw. -
Page 3: Table Of Contents
2054 .................. 34 can represent a health risk. 2055 .................. 34 Jonsered has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. English –... -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS PERSONAL PROTECTIVE EQUIPMENT CHAIN SAW SAFETY EQUIPMENT This section explains the various safety features of the saw, how they work, and basic inspection and maintenance you Most chain saw accidents happen when the should carry out to ensure safe operation. (See the ”What is chain touches the operator. - Page 5 SAFETY INSTRUCTIONS The front hand guard is 1 Chain brake and front hand guard not designed solely to YOUR chain saw is equipped with a chain brake that is desig- activate the chain brake. ned to stop the chain immediately if you get a kickback. Another important safety The chain brake reduces the risk of accidents, but only You can feature is that it prevents...
-
Page 6: Chain Catcher
SAFETY INSTRUCTIONS The way the chain brake is triggered, either manually or 2 Throttle lock automatically, depends on the force of the kickback and the The throttle lock is designed position of the chain saw in relation to the object that the to prevent accidental opera- kickback zone of the bar strikes. -
Page 7: Stop Switch
SAFETY INSTRUCTIONS 5 Vibration damping system 6 Stop switch Your chain saw is equipped Use the stop switch to switch with a vibration damping off the engine. system that is designed to minimise vibrations and make operation easier. When you use a chain saw vibrations are generated by the uneven contact between the chain and the wood you... -
Page 8: Inspecting, Maintaining And Servicing Chain Saw Safety Equipment
SAFETY INSTRUCTIONS Inspecting, maintaining and servicing Checking the inertia brake release chain saw safety equipment SPECIAL TRAINING IS REQUIRED to service Hold the chain saw over a and repair chain saws. This is especially true stump or other firm object. of chain saw safety equipment. - Page 9 SAFETY INSTRUCTIONS 2 Throttle lock 4 Right hand guard Make sure the throttle Check that the right hand control is locked at the guard is not damaged and idle setting when you that there are no visible release the throttle lock. defects, such as cracks.
-
Page 10: Cutting Equipment
SAFETY INSTRUCTIONS 7 Muffler CUTTING EQUIPMENT Never use a chain saw This section describes how to choose and maintain your cutting that has a faulty muffler. equipment in order to: • Reduce the risk of kickback. • Reduce the risk of the chain breaking or jumping. •... - Page 11 SAFETY INSTRUCTIONS 1 Cutting equipment designed to minimise C Some terms that describe the bar and chain When the cutting equipment supplied with your saw becomes kickback worn or damaged you will need to replace it. Use only the type of bar and chain recommended by us.
- Page 12 SAFETY INSTRUCTIONS It is very difficult to sharpen a 2 Sharpening your chain and adjusting chain correctly without the raker clearance right equipment. We recommend you use a file The risk of kickback is increased with a badly gauge. This will help you sharpened chain! obtain the maximum kickback reduction and cutting...
-
Page 13: Tensioning The Chain
SAFETY INSTRUCTIONS C General advice on setting raker clearance D Setting the raker clearance • When you sharpen the cutting teeth you reduce the RAKER CLEARANCE (cutting depth). To maintain • Before setting the raker clearance the cutting teeth should be cutting performance you newly sharpened. -
Page 14: Lubricating Cutting Equipment
SAFETY INSTRUCTIONS 4 Lubricating cutting equipment Poor lubrication of cutting equipment may cause the chain to snap and lead to serious, Undo the bar nuts that even fatal injuries. hold the clutch cover and chain brake, using the combination spanner. Then tighten the nuts by Prolonged inhalation of exhaust gases from hand as tight as you can. - Page 15 SAFETY INSTRUCTIONS C Checking chain lubrication E Lubricating the clutch drum bearing • Check the chain lubrication each time you refuel. Aim the tip of the saw at a light coloured surface about • Between the engine drive 20 cm away. After 1 minute shaft and the clutch drum is running at 3/4 throttle you a needle bearing that must...
-
Page 16: How To Avoid Kickback
SAFETY INSTRUCTIONS H Bar HOW TO AVOID KICKBACK Kickback can happen very suddenly and violently; kicking the saw, bar and chain back at the user. If this happens when the chain is Check regularly: moving it can cause very serious, even fatal injuries. - Page 17 SAFETY INSTRUCTIONS Take great care when you General rules cut with the top edge of If you understand what kickback is and how it happens then the bar, i.e. when cutting you can reduce or eliminate the element of surprise. By from the underside of the being prepared you reduce the risk.
-
Page 18: General Safety Precautions
SAFETY INSTRUCTIONS GENERAL SAFETY PRECAUTIONS STARTING Chain saws are designed solely for cutting wood. The only Long term inhalation of the engine's exhaust cutting equipment that can be used with this chain saw are fumes, chain oil mist and dust from sawdust the combinations of bars and chains recommended in the can represent a health risk. -
Page 19: General Working Instructions
SAFETY INSTRUCTIONS • Never try to refuel the saw 1 Basic safety rules while it is running. Look around you: • Make sure there is plenty of • to make sure there are no ventilation when refuelling people, animals or other or mixing fuel (2-stroke objects nearby that might mixture). -
Page 20: Basic Cutting Technique
SAFETY INSTRUCTIONS Make sure the chain will not strike the ground or any other object during or after cutting. Before moving your chain saw switch off the engine and lock the chain using Is there a risk of kick- the chain brake. Carry the back? saw with the bar and chain pointing backwards. -
Page 21: Tree Felling Technique
SAFETY INSTRUCTIONS 2 The log is supported at one 3 Tree felling technique end. There is a high risk that it will split. It takes a lot of experience to fell a tree. Inexperienced users of chain saws should not fell trees. - Page 22 SAFETY INSTRUCTIONS C Clearing the trunk and preparing your retreat FELLING CUT The felling cut is made from the opposite side of the tree and it Remove any branches that must be perfectly horizontal. Stand on the left side of the tree are in the way.
- Page 23 SAFETY INSTRUCTIONS We recommend that you use 4 Freeing a tree that has fallen badly = high a bar that is longer than the accident risk diameter of the tree, so that you can make the FELLING CUT and DIRECTIONAL CUT with single cutting stokes.
-
Page 24: What Is What
WHAT IS WHAT? Jonsered 2054 TURBO XXXX XXXXXXX Jonsered Huskvarna, SWEDEN J O N S E R E D S E R V I C E What is what? 1. Cylinder cover. 15. Saw bar. 2. Front handle. 16. Bumper. -
Page 25: Assembly
ASSEMBLY Mounting guide bar and chain Always wear gloves, when working with the chain, in order to protect your hands from Hold up the tip of the bar and injury. tighten the chain. The chain is correctly tensioned when there is no slack on the underside of the bar, but it can still be turned easily by hand. -
Page 26: Fuel Handling
Two-stroke oil • For the best results use JONSERED two-stroke oil, which is especially developed for chain saws. Mixing ratio 1:50 (2%). • If JONSERED two-stroke oil is not available, you may use another two-stroke oil of good quality that is intended for air cooled engines. -
Page 27: Chain Oil
FUEL HANDLING Chain oil Fuelling • The chain lubrication system is automatic. Always Taking the following precautions, will lessen use special chain oil with the risk of fire. good adhesive characteristics. • Do not smoke or place warm objects in the vicinity of the fuel. -
Page 28: Start And Stop
START AND STOP Start and stop Start Grip the front handle with your WARNING! left hand and hold the saw down by putting your right foot in the rear handle. Pull the • Never start a chain saw unless the bar, chain and all starter handle with your right covers are fitted correctly. -
Page 29: Maintenance
H-jet. The following engine speed applies: without hesitation and the saw 4-cycles a little at max speed. Max. overspeed 2054: 13 000 rpm, 2055: 14 000 rpm. Furthermore, the chain must not rotate at idling. A too lean Idling speed 2 500 rpm. -
Page 30: Starter Device
MAINTENANCE Starter device Tensioning the recoil spring • Lift the starter cord up in the notch on the starter WARNING! pulley and turn the starter pulley 2 turns clockwise. • When the recoil spring is assembled in the starter NOTE! Check that the housing, it is in tensioned position and can when starter pulley can be treated carelessly, pop out and cause injuries. -
Page 31: Air Filter
All bolts are specially made to withstand high temperatures. The electrode gap. Readjust if use of any bolts other than genuine Jonsered replacements necessary. The correct gap is may result in damage to the muffler and engine. All bolts must 0,5 mm (0,020"). -
Page 32: Cooling System
MAINTENANCE Cooling system Winter use During winter time, powder snow and cold weather can cause running problems, such as: • Too low engine temperature. To obtain the lowest possible running temperature the saw is • Icing on the air filter and carburettor. equipped with a cooling system.The cooling system Therefore some special measures are required:... -
Page 33: Daily Maintenance
MAINTENANCE Below you will find some general maintenance instructions. Weekly maintenance: If you have more questions, contact your servicing dealer. Daily maintenance: Check that the AV 1. Check the throttle trigger elements are not soft or for smooth operation. If any torn. -
Page 34: Technical Data
TECHNICAL DATA 2054 2055 2054 2055 Noise emissions Engine (see note 1) Cylinder volume, cm 53,2 53,2 Sound power level, measured Cylinder bore, mm dB(A) Stroke, mm Sound power level, guaranteed Idle speed, rpm 2 500 2 500 dB(A) Recommended max. speed,... - Page 35 EC type examination in accordance with the machinery directive's (98/37/EC) article 8, point 2c. The certificates for EC type examination in accordance with annex VI, have the numbers: K-EG 212 – 2054 Turbo, K-EG 201 – 2055 Turbo/2055W Turbo.
- Page 36 108 88 32-26 ´*xs6¶68¨ 2002W03...