Traxxas T-Maxx 3.3 4907 Owner's Manual page 31

MENU TREE
The menu tree below shows how to navigate through the
TQ 2.4GHz transmitter's various settings and functions. Press
and hold MENU to enter the menu tree, and use the following
commands to navigate through the menu and select options.
MENU: When you enter a menu, you always start at the top. Press
MENU to move down the menu tree. When you reach the
bottom of the tree, pressing MENU again will return you
to the top.
SET: Press SET to move across the menu tree and select
options. When an option is committed to the
transmitter's memory, the status LED will rapidly blink
green.
BACK: Press both MENU and SET to go back one level in the
menu tree.
EXIT: Press and hold MENU to exit programming. Your selected
options will be saved.
ECHO: Press and hold SET to activate the "echo" function. Echo
will "play back" your current position on the Menu Tree,
should you lose your place. For example: If your current
position is Steering Channel End Points, holding SET will
cause the LED to blink green twice, green once, and then
red three times. Echo will not alter your adjustments or
change your position in the programming sequence.
Below is an example of how to access a function in the menu
tree. In the example, the user is setting the Multi-Function knob
to be a steering Dual Rate control.
To set the Multi-Function knob to control STEERING DUAL RATE (%):
1. Switch the transmitter on
2. Press and hold MENU until the green LED lights. It will blink in single intervals.
3. Press SET. The red LED will blink in single intervals to indicate Steering Dual
Rate has been selected.
4. Press MENU twice. The red LED will blink three times repeatedly to indicate
Steering Percentage has been selected.
5. Press SET to select. The green LED will blink 8 times fast to indicate
successful selection.
6. Press and hold MENU to return to driving mode.
Restoring Factory Defaults:
Transmitter Hold both Transmitter Release MENU and
OFF MENU and SET ON SET. Red LED blinks
Set Multi-Function
knob for STEERING
Press/hold MENU Press SET
SENSITIVITY (Expo)
green LED blinks red LED blinks
Set Multi-Function
knob for THROTTLE
Press/hold MENU Press SET
SENSITIVITY (Expo)
green LED blinks red LED blinks
Set Multi-Function
knob for STEERING
Press/hold MENU Press SET
DUAL RATE (%)
green LED blinks red LED blinks
Set Multi-Function
knob for BRAKING
Press/hold MENU Press SET
PERCENTAGE (%)
green LED blinks red LED blinks
Set Multi-Function
knob for
Press/hold MENU Press SET
THROTTLE TRIM
green LED blinks red LED blinks
To LOCK the
Multi-Function knob
Press/hold MENU Press SET
green LED blinks red LED blinks
To REVERSE
the direction of
Press/hold MENU Press MENU
STEERING servo
green LED blinks green LED blinks (x2)
To set the SUB TRIM
of the STEERING
Press/hold MENU Press MENU
servo
green LED blinks green LED blinks (x2)
To set the END
POINTS of the
Press/hold MENU Press MENU
STEERING servo
green LED blinks green LED blinks (x2)
To reset the END
POINTS of STEERING
Press/hold MENU Press MENU
servo to defaults
green LED blinks green LED blinks (x2)
To REVERSE
the direction of
Press/hold MENU Press MENU
THROTTLE servo
green LED blinks green LED blinks (x2)
To set the SUB TRIM
of the THROTTLE
Press/hold MENU Press MENU
servo
green LED blinks green LED blinks (x2)
To set the END
POINTS of the
Press/hold MENU Press MENU
THROTTLE servo
green LED blinks green LED blinks (x2)
To reset the END
POINTS of THROTTLE
Press/hold MENU Press MENU
servo to defaults
green LED blinks green LED blinks (x2)
Enter Programming
Press and hold
MENU for 3 seconds
Multi-Function Knob
1
One Blink Green
Press
MENU
Channel Setup
2
Two Blinks Green
Press
MENU
Mode Selection
3
Three Blinks Green
Press
MENU
Traxxas-Link
4
Four Blinks Green
* Optional requires 4995X reverse kit.
Press MENU four
Press SET to clear settings. LED will turn solid
times. Red LED
green. Transmitter is restored to default
blinks 5 times
x 8
Press SET to confi rm Press/hold MENU
green LED blinks (x8) returns to driving mode
x 2 x 8
Press MENU to confi rm Press SET to select
red LED blinks (x2) green LED blinks (x8)
x 3 x 8
Press MENU twice Press SET to select
red LED blinks (x3) green LED blinks (x8)
x 4 x 8
Press MENU 3 times Press SET to select
red LED blinks (x4) green LED blinks (x8)
x 5 x 8
Press MENU 4 times Press SET to select
red LED blinks (x5) green LED blinks (x8)
x 6 x 8
Press MENU 5 times Press SET to lock
red LED blinks (x6) green LED blinks (x8)
x
2
Press SET Press SET
green LED blinks red LED blinks
x 2
Press SET Press SET
green LED blinks red LED blinks
x 2
Press SET Press SET
green LED blinks red LED blinks
x 2
Press SET Press SET
green LED blinks red LED blinks
x 2 x 2
Press SET Press MENU
green LED blinks green LED blinks (x2)
x 2 x 2
Press SET Press MENU
green LED blinks green LED blinks (x2)
x 2 x 2
Press SET Press MENU
green LED blinks green LED blinks (x2)
x x
2 2
Press SET Press MENU
green LED blinks green LED blinks (x2)
Press MENU to move through options.
Press SET to select an option.
1 Steering Sensitivity (Expo)
One Blink Red
Throttle Sensitivity (Expo)
2
Two Blinks Red
Steering % (Dual Rate)
3
Three Blinks Red
Braking %
4
Four Blinks Red
Press
Throttle Trim
5
SET
Five Blinks Red
Knob Disabled
6
Six Blinks Red
Steering (Channel 1)
1
Press
SET
One Blink Green
Throttle (Channel 2)
Press 2
MENU
Two Blinks Green
3 Shift (Channel 3)*
Three Blinks Green
Press SET to select an option.
Electric
Press 1
SET
One Blink Red
Press
MENU
2 Nitro
Two Blinks Red
Model Locking
1
Press
SET
One Blink Green
Press
MENU
Delete Model
2
Two Blinks Green
Press/hold MENU
returns to driving mode
Press/hold MENU
returns to driving mode
Press/hold MENU
returns to driving mode
Adjust the Multi-
Press/hold MENU Function knob until the
LED turns solid green.
returns to driving mode
Press/hold MENU
returns to driving mode
x
8
Press SET to reverse Press/hold MENU
servo direction returns to driving mode
x 2
Press MENU Use Multi-Function
red LED blinks (x2) knob to set neutral
x 3
Turn steering
Press MENU twice
wheel to desired max
red LED blinks (x3) left and right travel to save each position
x 4 x 8
Press MENU 3 times Press SET Press/hold MENU
red LED blinks (x4) to reset end points returns to driving mode
x 8
Press SET Press SET to reverse Press/hold MENU
red LED blinks servo direction returns to driving mode
x 2
Press SET Press MENU Use Multi-Function
red LED blinks red LED blinks (x2) knob to set neutral
x 3
Press SET Press MENU twice
trigger to set desired
red LED blinks red LED blinks (x3) max throttle or brake
x
4
Press SET Press MENU 3 times
red LED blinks red LED blinks (x4) green LED blinks (x8)
Note: The transmitter is "live" during programming
so you can test the settings real time without having
to exit the menu tree.
Press MENU to move through options.
Press SET to select an option.
Servo Reversing
1
One Blink Red
2 Sub Trim
Two Blinks Red
End Points
3
Three Blinks Red
Turn left to desired endpoint and press set to save.
To reset max throw: Let go of controls and press SET.
Reset End Points
4
Four Blinks Red
Press
SET
Press Servo Reversing
1
SET
One Blink Red
Sub Trim
2
Two Blinks Red
End Points
3
Press
Three Blinks Red
SET
forward to desired endpoint and press set to save.
To reset max throw: Let go of controls and press SET.
4 Reset End Points
Four Blinks Red
1 Servo Reversing
One Blink Red
Press Unlock
1
SET
One Blink Red
Lock
2
Two Blinks Red
3 Unlock All
Three Blinks Red
Press C onfi rm Deletion
1
SET
One Blink Red
MENU TREE FORMULAS
To select functions and make adjustments to the TQ 2.4GHz transmitter without
referencing the menu tree, turn your transmitter on, fi nd the function in the left
column you wish to adjust, and simply follow the corresponding steps.
1 1
Always turn your
transmitter on fi rst.
x 8
Press SET Press/hold MENU
to save position returns to driving mode
IF END POINTS
x 8
ARE OK:
Press SET Press/hold MENU
Turn steering wheel
to test settings returns to driving mode
x 8
Press SET Press/hold MENU
to save position returns to driving mode
IF END POINTS
ARE OK:
Use throttle
Press SET to save Press/hold MENU
Use trigger to test returns to driving mode
x
8
Press SET Press/hold MENU
returns to driving mode
Press SET to reverse
servo direction.
Use knob to adjust
sub-trim. Press SET to save.
Use steering wheel to
adjust. Turn right to desired
end point, press set to save.
Press SET to restore
factory default endpoints.
Press SET to reverse
servo direction.
Use knob to adjust
sub-trim. Press SET to save.
Use trigger to adjust. Pull
back to desired end point,
press set to save. Push
Press SET to restore
factory default endpoints.
Press SET to reverse
servo direction.
IF END POINTS
NEED TO BE
CHANGED:
Press SET
and repeat steps 6-8
IF END POINTS
NEED TO BE
CHANGED:
Press SET
and repeat steps 7-9
T-MAXX 3.3 • 31