HP L1506 Service Manual SERVICE MANUAL 15” LCD Monitor L1506 THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS RELIABILITY FOR CHANGES, ERRORS...
HP L1506 Service Manual Revision List Revision Date Change Description TPV Model name Jun-21-05 Initial release T560KC4DKHHPNP 1. Product Feature LCD Panel Driving system TFT Color LCD...
HP L1506 Service Manual Panel CLAA150XP02 Size 38.1cm(15.0") Pixel pitch 0.297mm( H )x 0.297mm( V ) Viewable angle 130˚ (H) 100˚ (V) Response time (typ.) <16 ms Brightness(Min) Contrast 400:1 Video Analog /Digital Sync. Type H/V TTL Input H-Frequency 30kHz – 63kHz...
HP L1506 Service Manual The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage. Monitor Block Diagram Flat Panel and CCFT Drive. CCFL backlight Power Board Main Board...
HP L1506 Service Manual When pressed, the monitor enters the off mode, and the LED turns blank. Press again to restore normal status. Left / Right Button: When the OSD show on screen, Left/Right Button are used to control the monitor functions. Press to switch functions or adjust settings.
HP L1506 Service Manual Brightness Adjust the brightness. Contrast Adjust the contrast Adjust the: Auto Adjustment: Adjusts the main settings and produces a stable, centered image. Image H-Position: horizontal position of the screen image. Control V-Position: vertical position of the screen image.
HP L1506 Service Manual Pixel Horz Freq Horz Vert Freq Vert Pixel Clk Preset Format (KHz) Polarity (Hz) Polarity (MHz) Source 640 x 480 31.469 59.940 25.175 640 x 480 37.861 72.809 31.500 VESA 640 x 480 37.500 75.000 31.500...
HP L1506 Service Manual 6.2 Software Flow Chart MCU initialize. Is the eeprom blank? Program the eeprom by default values. Get the PWM value of brightness from eeprom. Check the pin PANEL1 and PANEL2 to tell which panel to get with it.
HP L1506 Service Manual 8.2 INVERTER / POWER BOARD (715G1508-1)
Page 28
HP L1506 Service Manual 8.3 KEY BOARD ( 715G1532-D1-P) (715G1532-E-K)
Page 29
HP L1506 Service Manual 9. Maintainability 9.1 Equipments and Tools Requirement 1.) Multi-meter. 2.) Oscilloscope. 3.) Pattern Generator. 4.) DDC Tool with an IBM Compatible Computer. 5.) Alignment Tool. 6.) LCD Color Analyzer. 7.) Service Manual. 8.) User Manual.
HP L1506 Service Manual 9.2 Trouble Shooting 9.2.1 Main Board No power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 100-240 is normal Reinsert or check the Adapter/Inverter Measure U201 PIN2=1.8V...
Page 31
HP L1506 Service Manual No picture (LED orange) No picture The button if under X601 oscillate Replace X601 control waveform is normal Check Correspondent Check reset circuit of component U601 is normal Measure U201 PIN2=1.8V U202 PIN2=3.3V Replace U601 X401 oscillate...
Page 32
HP L1506 Service Manual White screen White screen Measure Q204 base X601 oscillate waveform is normal is high level? Replace X601 Check Q204,Q203 are Check reset circuit of broken or CN503 solder? U601 is normal Check Correspondent Check Correspondent component.
HP L1506 Service Manual 8.2.2 Inverter Board No power No power Check AC line volt 110V or 220V Check AC line Check the voltage of C905(+) Check F901, BD901 Check start voltage for the pin3 of IC901 Check R906, R907, IC901...
Page 34
HP L1506 Service Manual No backlight Check C845 (+) =12V Check R839 Check D808/Q809 Check ON/OFF signal Check Interface board Check IC801 pin5=12V voltage Check Q806/Q807/Q812 Check the pin19/20 of IC801 if have waveforms Short Q808/Q809 S D ,if the picture normal...
HP L1506 Service Manual 8.2.3 Key Pad Board OSD is unstable or not working Connect Key Pad Board Is Key Pad Board connecting normally? Replace Button Switch Is Button Switch normally? Is Key Pad Board Normally? Replace Key Pad Board...
C. 6500K color: Don’t adjust, Custom requires. 3. Into factory mode of HP L1506 A. Press DOWN button during 2 seconds along with press Power button will activate the factory mode, then MCU will do AUTO LEVEL automatically. Meanwhile press MENU the OSD screen will located at THE LEFT TOP OF PANEL.
HP L1506 Service Manual the value R=100 5. Adjust the GREEN of color 9300K on factory window until chroma 7120 indicator reached the value G=100 6. Adjust the BLUE of color 9300K on factory window until chroma 7120 indicator reached the value B=100 7.
Page 38
HP L1506 Service Manual and different models. Ⅱ. Steps of white-balance adjustment for LCD:(Take 17 ”HP LCD for example) 1. Required instruments: Chroma7120、Chroma2325(BGA265A) 。 First connect the instruments together and turn on the LCD power, then warm up for 30 minutes under full white screen mode.
Page 39
HP L1506 Service Manual 7. Select 7x00 item to adjust cool color-temperature and select 6x00 to adjust warm color- temperature. It can reach to the best effect through adjusting R/G/B value if it inclines to green or blue. 8. Select Exit to the upper menu after completing the adjustment. Then press POWER OFF to exit and save it.
Page 40
HP L1506 Service Manual “Data compare error !” to indicate failure if the DDC-writing doesn’t perform well. Please check the appear power resource and the connection of the signal cable, then return to step 3 by pressing ENTER and re-do it.
HP L1506 Service Manual 13. BOM List T560KC4DKHHPNP Location Part No. for TPV Description CBPC560KC4HPNP CONVERSION BOARD KEPC560KHP5P KEY BOARD KEPC980KHP4P KEY BOARD PWPC1521CPH1P POWER BOARD 15G8159 3 MAIN FRAME 33G4856 EY L LOGO PLATE 33G4889 EY L STAND CAP...