TPC-1770/1780 Intel Touch Panel Computer with High Luminance 17" SXGA TFT LCD User Manual...
Page 2
Acknowledgements Intel and Pentium are trademarks of Intel Corporation. Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp. All other product names or trademarks are properties of their respective owners.
Page 3
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its prod- ucts will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper instal- lation.
- Product name and serial number - Description of your peripheral attachments - Description of your software (operating system, version, appli- cation software, etc.) - A complete description of the problem - The exact wording of any error messages TPC-1770/1780 User Manual...
Page 5
Safety Instructions Read these safety instructions carefully. Keep this User's Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for clean- ing. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
Page 6
The sound pressure level at the operator's position according to IEC 704- 1:1982 is no more than 70 dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. TPC-1770/1780 User Manual...
Chapter 1 General Information 1.1 Introduction The TPC-1770/1780 TPC is state-of-the-art HMI. This 17" display opera- tor interface is an x86-based platform with these key features: Fanless: By using a low power processor, the system does not have to rely on fans, which are unreliable, and cause dust to circulate inside the equipment.
1.2.2 I/O Ports Item TPC-1770H TPC-1780H 10/100/1000 Base-T x 2, 10/100/1000 Base-T x 2, I/O port (Realtek RTK8111B) (Realtek RTK8111B) RS-232 x 3 (COM1, RS-232 x 3 (COM1, COM3, COM4) COM3, COM4) VGA x 1 VGA x 1 USB 2.0 x 4 USB 2.0 x 4 PS/2 Mouse interface x 1 PS/2 Mouse interface x 1 PS/2 Keyboard interface...
50,000 hours Backlight Life Time Note There might be several bright or dark pixels on the LCD. This comes from the production of the LCD. Such phenomenon is claimed to be normal accord- ing to the LCD manufacturers. TPC-1770/1780 User Manual...
1.4 Touchscreen Specifications Resistive Touchscreen Type Tempered Glass Base Glass Construction 1024 x 1024 Resolution 80% typical Light Transmission USB Interface Controller 3.3 to 5V Power Rating 1 million touches Durability 1.5 Power Input voltage: 18 ~ 32 Vdc, 5.55-3.12A Max (the fuse will be open circuit as input level exceeds 33Vdc) Chapter 1...
Make sure the waterproof gasket is in position before installing the TPC-1770/1780 to the panel opening. 2. Install the TPC-1770/1780 to the panel opening. 3. Find out the ten clampers and ten long screws in the accessory pack. Hook those clampers to those holes around the four sides of the bezel.
1.8 Dimensions & Cutout Weight: 8 Kg (without HDD) Dimensions: 414 x 347.5 x 93 mm (16.3" x 13.68" x 3.66") (WxHxD) Cutout: 400.8 x 334.3 mm (suggested) Figure 1.3: Dimensions TPC-1770/1780 User Manual...
Chapter 2 System Setup This chapter provides a brief explanation for operating the TPC-1770/ 1780. It is easy to make the TPC-1770/1780 start working with the below step-by-step. Step 1: Unpack the TPC-1770/1780 package. Please check the packing list at the beginning of this manual.
Figure 2.3: Power Receptor Step 4: Plug the power lines to the system power receptor. Step 5: Push the power button to power on the system as the figure 2.4. Figure 2.4: Power Button Chapter 2...
Chapter 4 Software Configuration A support CD-ROM for TPC-1770/1780 is available and along with the product. There are related utilities and drivers for TPC-1770/1780 included. Please install the Chipset INF driver, VGA graphics driver, LAN driver, audio driver, Advantech.com driver, Touchscreen driver and Watchdog Timer (WDT) driver sequentially.
4.1.3 LAN Driver Path: \TPC-1770H\XP\LAN\ \TPC-1780H\XP\LAN\ \TPC-1780H\VISTA32\LAN\ \TPC-1780H\VISTA64\LAN\ Available for the OS’s below: • Microsoft Windows XP • Microsoft Vista 4.1.4 Touchscreen Driver Path: \TPC-1770H\XP\TouchScreen\ \TPC-1780H\XP\TouchScreen\ \TPC-1780H\VISTA32\TouchScreen\ \TPC-1780H\VISTA64\TouchScreen\ Available for the OS’s below: • Microsoft Windows XP • Microsoft Vista 4.1.5 Audio Driver Path: \TPC-1770H\XP\Audio\ \TPC-1780H\XP\Audio\...
Chapter 5 Windows XP Embedded TPC-1770/1780 is in support of embedded windows platform. This sec- tion is to state the important features, EWF and HORN, provided in win- dows XP embedded. 5.1 EWF EWF stands for Enhanced Write Filter. It provides an upper filter in the storage device driver stack that redirects disk write operations to volatile (RAM) or non-volatile (disk) storage.
The hibernation file required is dependent on the RAM size you use on the system. In other words, the hibernation file is 512MB that is the same as memory size used on TPC-1770/1780. 5.3 Advantech Utilities 5.3.1 Version Information Start menu->...
Please follow the steps before running this utility to create full HORM environment. Enable Hibernation via Power Options in Control Panel Make C: partition EWF-enabled via OSLock Make sure that all volumes to be dismounted are not in use. TPC-1770/1780 User Manual...
Appendix A WDT Programming A.1 Overview The TPC-1770/1780 cards’ watchdog timer can be used to monitor sys- tem software operation and take corrective action if the software fails to function after the programmed period. This section describes the opera- tion of the watchdog timer, and how to program it.
A.2 Watchdog Timer Programming The I/O port address of the watchdog timer is 2E(hex) and 2F(hex), 2E (hex) is the address port. 2F(hex) is the data port. You must first assign the address of register by writing address value into address port 2E(hex), then write/read data to/from the assigned register through data port 2F (hex).
; select watchdog registers ;---------------------------- al, 7 dx, 2Eh dx, al dx, 2Fh al, 0ah dx, al ;---------------------------- ; get base address ;---------------------------- al, 60h dx, 2Eh dx, al dx, 2Fh al, dx ah, al al, 61h TPC-1770/1780 User Manual...
Page 41
dx, 2Eh dx, al dx, 2Fh al, dx ; now, AX contains the base address bx, ax ; save base address in BX ;---------------------------- ; exit configuration state ;---------------------------- dx, 2Eh al, 0AAh dx, al ;---------------------------- ; select WDT pin ;---------------------------- dx, bx dx, 47h...
Page 42
; enter configuration state ;---------------------------- dx, 2Eh al, 55h dx, al ;---------------------------- ; select watchdog registers ;---------------------------- al, 7 dx, 2Eh dx, al dx, 2Fh al, 0ah dx, al ;---------------------------- ; get base address ;---------------------------- al, 60h TPC-1770/1780 User Manual...
Page 43
dx, 2Eh dx, al dx, 2Fh al, dx ah, al al, 61h dx, 2Eh dx, al dx, 2Fh al, dx ; now, AX contains the base address bx, ax ; save base address in BX ;---------------------------- ; exit configuration state ;---------------------------- dx, 2Eh al, 0AAh...
Page 44
3. Enable watchdog timer to be reset upon mouse interrupt (Note: WDT timeout value must be set before this function can work) ;---------------------------- ; enter configuration state ;---------------------------- dx, 2Eh al, 55h dx, al ;---------------------------- ; select watchdog registers ;---------------------------- al, 7 dx, 2Eh TPC-1770/1780 User Manual...
Page 45
dx, al dx, 2Fh al, 0ah dx, al ;---------------------------- ; get base address ;---------------------------- al, 60h dx, 2Eh dx, al dx, 2Fh al, dx al, 8 al, 61h dx, 2Eh dx, al dx, 2Fh al, dx ; now, AX contains the base address bx, ax ;...
Page 46
(Note: WDT timeout value must be set before this function can work) ;---------------------------- ; enter configuration state ;---------------------------- dx, 2Eh al, 55h dx, al ;---------------------------- ; select watchdog registers ;---------------------------- al, 7 dx, 2Eh dx, al dx, 2Fh al, 0ah dx, al ;---------------------------- ; get base address TPC-1770/1780 User Manual...
Page 47
;---------------------------- al, 60h dx, 2Eh dx, al dx, 2Fh al, dx al, 8 al, 61h dx, 2Eh dx, al dx, 2Fh al, dx ; now, AX contains the base address bx, ax ; save base address in BX ;---------------------------- ; exit configuration state ;---------------------------- dx, 2Eh al, 0AAh...
Page 48
55h dx, al ;---------------------------- ; select watchdog registers ;---------------------------- al, 7 dx, 2Eh dx, al dx, 2Fh al, 0ah dx, al ;---------------------------- ; get base address ;---------------------------- al, 60h dx, 2Eh dx, al dx, 2Fh al, dx TPC-1770/1780 User Manual...
Page 49
al, 8 al, 61h dx, 2Eh dx, al dx, 2Fh al, dx ; now, AX contains the base address bx, ax ; save base address in BX ;---------------------------- ; exit configuration state ;---------------------------- dx, 2Eh al, 0AAh dx, al ;---------------------------- ;...
Please follow the assembly procedure to install the HDD into the system. Remove the rear HDD cover. Figure B.1: Removing the Rear HDD Cover Deassemble the HDD kit from the system. Figure B.2: Removing the Top Screws TPC-1770/1780 User Manual...
Put the HDD into the HDD bracket and fasten the screws.. Figure B.3: Installing the HDD Paste the Mylar (from assembly box) Figure B.4: Pasting the Mylar Appendix B...
5. Put the HDD to the system and fasten the screws. Figure B.5: Attaching the HDD 6. Re-attach the rear cover and fasten the screws. The HDD has been installed successfully. TPC-1770/1780 User Manual...
Step 2: Replace the damaged fuse with a new one Step 3: Place the fuse cover back in position Figure C.1: Fuse Replacement Warning Do NOT replace the fuse unless it is damaged. Do NOT replace the fuse with a different rating. TPC-1770/1780 User Manual...