Functions 2.3 Canceling EXT OPTION 3 Self-Check Mode 3.1 Procedure to enter the LCD Projector self-check mode 3.2 Self Check Display and PT-AE700U Contents PT-AE700E 3.3 Canceling the self-check mode 4 Service Mode 4.1 Procedure to enter the service mode 4.2 Canceling the service...
Page 2
6.2 Removal of Upper Case 6.3 Removal of A-P.C. Board 6.4 Removal of S-P.C.Board 6.5 Removal of J-P.C.Board (PT-AE700E only) 6.6 Removal of B / Q- Module 6.7 Removal of P-Module 6.8 Removal of K-P.C. Board 6.9 Removal of Lamp Unit 6.10 Removal of Analysis Block and Projection Lens 6.11 Removal of LCD Block...
Table Of Contents COVER 1 Safety Precautions 1.1 General Guidelines 1.2 Leakage Current Check 1.3 UV Precaution and UHM Lamp Precautions 2 Ext Option 2.1 Procedure to enter EXT OPTION 2.2 EXT OPTION Menu and Functions 2.3 Canceling EXT OPTION 3 Self-Check Mode 3.1 Procedure to enter the self-check mode 3.2 Self Check Display and Contents...
Page 6
5.3 Canceling the flicker adjustment mode 6 Disassembly Instructions 6.1 Printed Circuit Board and Main Parts Location 6.2 Removal of Upper Case 6.3 Removal of A-P.C.Board 6.4 Removal of S-P.C.Board 6.5 Removal of J-P.C.Board (PT-AE700E only) 6.6 Removal of B / Q-Module 6.7 Removal of P-Module 6.8 Removal of K-P.C.Board 6.9 Removal of Lamp Unit...
Page 7
6.20 Removal of Iris Unit 7 Measurement and Adjustments 7.1 Adjustment Procedure Flowchart 7.2 Cautions for Adjustment 7.3 Setting Before Adjustment 7.4 Convergence Adjustment 7.4.1 Tools to be used 7.4.2 Preparation 7.4.3 Adjustment Procedure 7.5 Lighting Area Adjustment 7.5.1 Tools to be used 7.5.2 Preparation 7.5.3 Adjustment Procedure 7.6 Software for Adjustment...
Page 8
7.7.1 Adjustment Menu 7.7.2 Explanation of Buttons 7.7.3 Equipment to be used 7.7.4 Adjustment Procedure 7.8 Input Level Adjustment (RGB) 7.8.1 Adjustment Menu 7.8.2 Explanation of Buttons 7.8.3 Equipment to be used 7.8.4 Adjustment Procedure 8 Troubleshooting 9 Interconnection Block Diagram 9.1 Interconnection Block Diagram (1 / 2) 9.2 Interconnection Block Diagram (2 / 2) 10 Block Diagram...
1 Safety Precautions TOP PREVIOUS NEXT 1.1 General Guidelines 1.2 Leakage Current Check 1.3 UV Precaution and UHM Lamp Precautions TOP PREVIOUS NEXT...
1.1 General Guidelines TOP PREVIOUS NEXT For continued safety, no modification of any circuit must be attempted. Unplug the power cord from the power outlet before disassembling this projector. It is advisable to use an isolation transformer in the AC power line before the service. Observe the original lead dress during the service.
1.2 Leakage Current Check TOP PREVIOUS NEXT 1. Prepare the measuring circuit as shown in Fig.1. Be sure to use a voltmeter having the performance described in Table 1. Fig. 1 Table 1 Fig. 2 2. Assemble the circuit as shown in Fig. 2. Plug the power cord in a power outlet. 3.
Page 16
5. The voltmeter must read 0.375 V or lower in both of steps 3 and 4. This means that the current must be 0.75 mA or less. 6. If the reading is out of the above standard, the projector must be repaired and rechecked before returning to the customer because of a possibility of an electric shock.
1.3 UV Precaution and UHM Lamp Precautions TOP PREVIOUS NEXT Be sure to unplug the power cord from the power outlet when replacing the lamp. Because the lamp reaches a very high temperature during its operation, wait until it cools completely when replacing the Lamp Unit.
2 Ext Option TOP PREVIOUS NEXT This projector has EXT OPTION in addition to standard on-screen menus. There are SELF CHECK, SERVICE MODE and FLICKER ADJ for service, etc. 2.1 Procedure to enter EXT OPTION 2.2 EXT OPTION Menu and Functions 2.3 Canceling EXT OPTION TOP PREVIOUS NEXT...
2.1 Procedure to enter EXT OPTION TOP PREVIOUS NEXT 1. Press "MENU" button on the main unit or remote control unit to display "MENU" screen, then select "OPTION" and press "ENTER" button. 2. Select "OSD" on "OPTION" menu and press "ENTER" button 3 seconds or longer. MENU OPTION TOP PREVIOUS NEXT...
2.2 EXT OPTION Menu and Functions TOP PREVIOUS NEXT FREEZE MSG Switching ON/OFF "FREEZE" on-screen display PIC.SHIFT Switching ON/OFF the antipersistence function Shifts the picture slightly (by one dot) when every 60 minutes. (one dot shifting three times, one dot shifting three times in reverse direction, and repeats them alternately.) RUNTIME PRT Switching ON/OFF the shutdown when the operation time for the lamp unit is 2 000 hours or longer...
Page 21
NORMAL: To set the normal mode (the dot clock is adjusted strictly) SPECIAL: To set the special mode (the dot clock is adjusted roughly) * Do not change the initial setting (NORMAL). SELF CHECK To enter the self-check mode SERVICE MODE To enter the service mode FLICKER ADJ To enter the flicker adjustment mode...
3 Self-Check Mode TOP PREVIOUS NEXT This mode is used to narrow down the location of the failure. 3.1 Procedure to enter the self-check mode 3.2 Self Check Display and Contents 3.3 Canceling the self-check mode TOP PREVIOUS NEXT...
3.1 Procedure to enter the self-check mode TOP PREVIOUS NEXT Select "SELF CHECK" on "EXT OPTION" menu and press "ENTER" button on the main unit or remote control unit. TOP PREVIOUS NEXT...
4 Service Mode TOP PREVIOUS NEXT This mode is used to display seven kinds of test patterns [Horizontal lines, Vertical lines, Dots, Crosshatch, White cross, Black cross and White (No pattern)] in the four colors (White, Red, Green and Blue). Note: On the service mode, displays above patterns by each color without test equipment such as PC or SG.
4.1 Procedure to enter the service mode TOP PREVIOUS NEXT Select "SERVICE MODE" on "EXT OPTION" menu and press "ENTER" button on the main unit or remote control unit. Note: In the service mode, pressing the up-arrow " " or down-arrow " "...
5 Flicker Adjustment Mode TOP PREVIOUS NEXT If replacing the optical parts (LCD Panel / LCD block) or A-P.C.Board of this projector, enter the flicker adjustment mode and minimize the flicker. 5.1 Procedure to enter the adjustment mode 5.2 Adjustment Display and Contents 5.3 Canceling the flicker adjustment mode TOP PREVIOUS NEXT...
5.1 Procedure to enter the adjustment mode TOP PREVIOUS NEXT Select "FLICKER ADJ" on "EXT OPTION" menu and press "ENTER" button on the main unit or remote control unit. Note: "DESK setting (blue)" is displayed when entering the adjustment mode. TOP PREVIOUS NEXT...
5.2 Adjustment Display and Contents TOP PREVIOUS NEXT Setting value is increased and decreased with the right-arrow " " and left-arrow " " buttons. " ": Decrease, " ": Increase Adjust the setting value to minimize the flicker on the screen. Execute the adjustment by 6 patterns below.
5.3 Canceling the flicker adjustment mode TOP PREVIOUS NEXT Press "MENU" button on the main unit or remote control unit. Note: When "MENU" button is pressed, the setting value at that time is saved into this projector and the adjustment mode is canceled. TOP PREVIOUS NEXT...
6 Disassembly Instructions TOP PREVIOUS NEXT Warning: Be sure to unplug the power cord from the power outlet before disassembling this projector. Caution: While turning over a printed circuit board, be sure to put a insulating material under it to prevent a short circuit.
Page 36
6.11 Removal of LCD Block 6.12 Removal of Projection Lens 6.13 Replacement of LCD Panel 6.14 LCD Panel Discrimination 6.15 LCD Panel Combination 6.16 Replacement of Projection Polarizer 6.17 Replacement of Incidence Polarizer (R and B) 6.18 Replacement of Incidence Polarizer (G) 6.19 Replacement of PBS Array (Analysis Block) 6.20 Removal of Iris Unit TOP PREVIOUS NEXT...
6.2 Removal of Upper Case TOP PREVIOUS NEXT 1. Remove the cap of the lens shift lever. 2. Unscrew the nut in the shift lever. Note: Turn clockwise the nut to unscrew. 3. Turn counterclockwise the shift lever and remove it. 4.
Page 39
6. Return the projector to the normal position. 7. Remove the upper case. TOP PREVIOUS NEXT...
6.3 Removal of A-P.C.Board TOP PREVIOUS NEXT 1. Remove the upper case according to the section 6.2. "Removal of Upper Case". 2. Unscrew the 3 screws and remove the connector cover. 3. Unscrew the 2 screws and remove the A-P.C.Board block. 4.
6.4 Removal of S-P.C.Board TOP PREVIOUS NEXT 1. Remove the upper case according to the section 6.2. "Removal of Upper Case". 2. Unscrew the 2 screws and remove the S-P.C.Board. TOP PREVIOUS NEXT...
6.5 Removal of J-P.C.Board (PT-AE700E only) TOP PREVIOUS NEXT 1. Remove the upper case according to the section 6.2. "Removal of Upper Case". 2. Unscrew the 3 screws and remove the connector cover. 3. Unscrew the 3 screws and remove the J-P.C.Board. TOP PREVIOUS NEXT...
6.6 Removal of B/Q-Module TOP PREVIOUS NEXT 1. Remove the upper case according to the section 6.2. "Removal of Upper Case". 2. Unscrew the 2 screws and remove the S-P.C.Board. 3. Unhook the hook section and remove the duct cover. 4.
Page 44
10. Unhook the hook section of resin spacer and remove the B/Q-Module. TOP PREVIOUS NEXT...
6.7 Removal of P-Module TOP PREVIOUS NEXT 1. Remove the power box according to the steps 1 through 5 in the section 6.6. "Removal of B/Q- Module". 2. Unscrew the 2 screws and remove the P-Module. TOP PREVIOUS NEXT...
6.8 Removal of K-P.C.Board TOP PREVIOUS NEXT 1. Remove the A-P.C.Board block according to the steps 1 through 3 in the section 6.3. "Removal of A-P.C.Board". 2. Unscrew the 2 screws and remove the K-P.C.Board block. 3. For PT-AE700E, unscrew the 2 screws and remove the J-P.C.Board. TOP PREVIOUS NEXT...
6.9 Removal of Lamp Unit TOP PREVIOUS NEXT 1. Turn the projector upside down. 2. Loosen the 2 screws until they idle and remove the lamp unit cover. 3. Unscrew the 2 screws fixing the lamp unit and remove the lamp unit. TOP PREVIOUS NEXT...
6.10 Removal of Analysis Block and Projection Lens TOP PREVIOUS NEXT 1. Remove the lamp unit according to the section 6.9. "Removal of Lamp Unit". 2. Remove the A-P.C.Board block according to the steps 1 through 3 in the section 6.3. "Removal of A-P.C.Board".
Page 49
8. Unscrew the 4 screws and remove the projection lens block (with shift mechanism). 9. Unscrew the 3 screws and remove the LCD duct and PBS fan. TOP PREVIOUS NEXT...
6.11 Removal of LCD Block TOP PREVIOUS NEXT 1. Remove the A-P.C.Board block according to the steps 1 through 3 in the section 6.3. "Removal of A-P.C.Board". 2. Unscrew the 2 screws and remove the LCD block. TOP PREVIOUS NEXT...
6.12 Removal of Projection Lens TOP PREVIOUS NEXT 1. Remove the projection lens block according to the steps 1 through 8 in the section 6.10. "Removal of Analysis Block and Projection Lens". 2. Unscrew the 4 screws and separate the projection lens and the shift mechanism. TOP PREVIOUS NEXT...
6.13 Replacement of LCD Panel TOP PREVIOUS NEXT The procedure is described as an example of LCD panel (B). 1. Remove the LCD block according to the section 6.11. "Removal of LCD Block". 2. Cut the 4 LCD panel installation spindles at the position A and remove the LCD panel. 3.
Page 53
6. Reassemble the projector in the reverse order of disassembling, but leave the upper case and the screws fixing the A-P.C.Board block as they are removed. 7. Adjust the convergence according to the section 7.4. "Convergence Adjustment". 8. After the adjustment, while paying attention not to vary the adjusting result, tighten the 2 screws (upper) fixing the panel attachment temporarily with a hexagon head wrench.
Page 54
11. Adhere the shading sheet as it was. 12. Reassemble the projector as it was. TOP PREVIOUS NEXT...
6.14 LCD Panel Discrimination TOP PREVIOUS NEXT ID-tag seal color LCD panel LCD panel (R) Blue LCD panel (B) (No seal) LCD panel (G) Since the ID-tag seal is pasted to the FPC of LCD Panl, (R), (G) or (B) can be easily identified by the color of the seal.
6.15 LCD Panel Combination TOP PREVIOUS NEXT Part number is printed on the FPC of LCD Panel. When replacing LCD Panel, use a component which has the same part number as the original. LCD panel Combination 1 Combination 2 L5BDAXQ00188 L5BDAXQ00191 (L3D07H-55G01) (L3D07H-56G01)
6.16 Replacement of Projection Polarizer TOP PREVIOUS NEXT 1. Remove the LCD block according to the section 6.11. "Removal of LCD Block". 2. Remove the projection polarizer which requires replacing. (The projection polarizer is adhered with the adhesive tape.) Note: Be careful not to damage peripheral components (prism, LCD panel, etc.).
6.17 Replacement of Incidence Polarizer (R and TOP PREVIOUS NEXT 1. Remove the A-P.C.Board block according to the steps 1 through 3 in the section 6.3. "Removal of A-P.C.Board". 2. Unscrew the 2 screws and release the lamp unit terminal. 3.
Page 60
7. Replace the incidence polarizer. Note: Be careful not to touch the surface of incidence polarizer. TOP PREVIOUS NEXT...
6.18 Replacement of Incidence Polarizer (G) TOP PREVIOUS NEXT 1. Remove the A-P.C.Board block according to the steps 1 through 3 in the section 6.3. "Removal of A-P.C.Board". 2. Mark positions of the incidence polarizer (G). Note: Mark accurately as possible because the marks will be used for resetting the incidence polarizer position.
6.19 Replacement of PBS Array (Analysis Block) TOP PREVIOUS NEXT 1. Remove the analysis case (upper) according to the steps 1 through 6 in the section 6.17. "Replacement of Incidence Polarizer (R and B)". Note: Because the hook is damaged easily, be careful not to expand it excessively. 2.
6.20 Removal of Iris Unit TOP PREVIOUS NEXT 1. Remove the analysis Block according to the steps 1 through 7 in the section 6.10. "Removal of Analysis Block and Projection Lens". 2. Unscrew the 2 screws and remove the analysis case (upper) while expanding the hook of it outside.
7 Measurement and Adjustments TOP PREVIOUS NEXT 7.1 Adjustment Procedure Flowchart 7.2 Cautions for Adjustment 7.3 Setting Before Adjustment 7.4 Convergence Adjustment 7.4.1 Tools to be used 7.4.2 Preparation 7.4.3 Adjustment Procedure 7.5 Lighting Area Adjustment 7.5.1 Tools to be used 7.5.2 Preparation 7.5.3 Adjustment Procedure 7.6 Software for Adjustment...
Page 66
7.7.1 Adjustment Menu 7.7.2 Explanation of Buttons 7.7.3 Equipment to be used 7.7.4 Adjustment Procedure 7.8 Input Level Adjustment (RGB) 7.8.1 Adjustment Menu 7.8.2 Explanation of Buttons 7.8.3 Equipment to be used 7.8.4 Adjustment Procedure TOP PREVIOUS NEXT...
7.2 Cautions for Adjustment TOP PREVIOUS NEXT Never turn off the MAIN POWER switch until every fan completely stops. To maintain and ensure safety, always use the designated components for replacement parts. If removing any clamps, lead wires or connectors, always place them back in their proper locations.
7.3 Setting Before Adjustment TOP PREVIOUS NEXT Set up the projector to obtain the projection distance below. Turn the zoom ring of the projector to obtain the largest size of the picture. TOP PREVIOUS NEXT...
7.4 Convergence Adjustment TOP PREVIOUS NEXT Execute this adjustment when replacing the LCD panel. 7.4.1 Tools to be used 7.4.2 Preparation 7.4.3 Adjustment Procedure TOP PREVIOUS NEXT...
7.4.1 Tools to be used TOP PREVIOUS NEXT Service Kit (Part No. TZSH07017): This kit is composed of 3 extension flexible cables and 3 connector extension cables. Note: Consult your dealer or Authorized Service Center for the service kit. TOP PREVIOUS NEXT...
7.4.2 Preparation TOP PREVIOUS NEXT 1. Loosen 2 screws fixing the panel adjuster and 3 screws fixing the panel attachment, then tighten the 5 screws temporarily just until the LCD panel can be shifted by your fingers. Note: See figures in the section 6.13. "Replacement of LCD Panel" for 2 screws fixing the panel adjuster and 3 screws fixing the panel attachment.
7.4.3 Adjustment Procedure TOP PREVIOUS NEXT Prepare 2 pieces of thick black paper (23 mm × 100 mm) that can be shaded. Cover and shade LCD panels with the paper except the panel for adjustment. 7.4.3.1 When replacing single LCD panel (R, G or B) The procedure is described as an example when LCD panel (B) is replaced.
7.5.1 Tools to be used TOP PREVIOUS NEXT Service Kit (Part No. TZSH07017): This kit is composed of 3 extension flexible cables and 3 connector extension cables. Note: Consult your dealer or Authorized Service Center for the service kit. TOP PREVIOUS NEXT...
7.5.2 Preparation TOP PREVIOUS NEXT 1. Remove the upper case and the connector cover according to the steps 1 through 2 in the section 6.3. "Removal of A-P.C.Board". 2. Unscrew the 2 screws. 3. Connect the service kit (extension cables). Each flexible cable of LCD Panels (R/G/B) - Connectors (A1/A2/A3) on A-P.C.Board Ballast block [Connector (Q3) on Q-Module] - Connector (A4) on A-P.C.Board Intake fan connector - Connector (A15) on A-P.C.Board...
7.5.3 Adjustment Procedure TOP PREVIOUS NEXT 7.5.3.1 Outline When the lighting area is off from the adjustment and color unevenness appears, adjust the lighting area into correct position. Symptom Measure Magenta unevenness G Reflector Adjustment Cyan unevenness R Reflector Adjustment Yellow unevenness B Reflector Adjustment Shifting the mirror adjusting lever horizontally, adjust color unevenness on the screen upper/...
Page 81
3. Adjust the mirror adjusting lever A position to minimize color unevenness on the screen by shifting the lever in arrow directions. 4. Tighten the 2 screws. 7.5.3.3 R Reflector Adjustment 1. Turn on the power and display 100 % white pattern on the screen. 2.
7.6 Software for Adjustment TOP PREVIOUS NEXT 7.6.1 Outline 7.6.2 Operating Procedure 7.6.3 Port Name and Projector Selection Menu 7.6.4 Data Transmission / Reception Menu 7.6.5 Adjustment Menu TOP PREVIOUS NEXT...
7.6.1 Outline TOP PREVIOUS NEXT This projector needs computer-aided adjustments. After the software adjustments, this projector must be turned off and on again to memorize the settings. Connect the connection interface and communication cable between the projector and a PC as shown below.
7.6.2 Operating Procedure TOP PREVIOUS NEXT 1. Run the software program by the keyboard entry. Note: Use the software program as below. Adjustment Tool [AE700] 2. The first menu is Port selection menu. 3. Adjust the projector by selecting the necessary item from the menu in each stage. TOP PREVIOUS NEXT...
7.6.3 Port Name and Projector Selection Menu TOP PREVIOUS NEXT Select the port name of PC which connects with the projector, then click [Data] or [Adjustment] button. 7.6.3.1 Explanation of Buttons Data: Displays the data transmission/reception menu. Adjustment: Displays the adjustment menu. Exit: Exits this application.
7.6.4 Data Transmission/Reception Menu TOP PREVIOUS NEXT 7.6.4.1 Explanation of Buttons Micom Data Transmission: Reads the microcomputer data from the file and transmits it to the projector. Micom Data Reception: Receives the microcomputer data from the projector and writes it in the file. Gamma Data Transmission: Reads the gamma data from the file and transmits it to the projector.
Page 87
Uniformity Data Transmission: Reads the color unevenness correction data from the file and transmits it to the projector. Uniformity Data Reception: Receives the color unevenness correction data from the projector and writes it in the file. Color Management Data Transmission: Reads the color management data from the file and transmits it to the projector.
7.7 Flicker Adjustment TOP PREVIOUS NEXT 7.7.1 Adjustment Menu 7.7.2 Explanation of Buttons 7.7.3 Equipment to be used 7.7.4 Adjustment Procedure TOP PREVIOUS NEXT...
7.7.2 Explanation of Buttons TOP PREVIOUS NEXT Desk: Sets the installation mode to the desk setting and receive the current data. (This button is usually set for its inactive mode.) Ceiling: Sets the installation mode to the ceiling setting and receive the current data. (This button is usually set for its inactive mode.) B Signal Adj.: Sets the test signal mode to the B-signal and allows the "...
Page 92
Changes the setting value and transmits its data. (The 8 and 2 keys on the keyboard have the same functions.) If releasing the mouse or key after pressing it continuously, the data is transmitted once. The variable setting value is enclosed ina box and using the TAB or SPACE key allows the move of the box.
7.7.4 Adjustment Procedure TOP PREVIOUS NEXT 1. Display Flicker Adjustment menu. 2. Click "B Signal Adj," and the blue flicker adjustment pattern will be displayed. 3. Minimize the flicker while observing the projected pattern. 4. Click "R Signal Adj," and the red flicker adjustment pattern will be displayed. 5.
7.8 Input Level Adjustment (RGB) TOP PREVIOUS NEXT 7.8.1 Adjustment Menu 7.8.2 Explanation of Buttons 7.8.3 Equipment to be used 7.8.4 Adjustment Procedure TOP PREVIOUS NEXT...
7.8.2 Explanation of Buttons TOP PREVIOUS NEXT Executes automatic sub contrast and sub brightness adjustments, then closes this dialog. Cancel: Cancels this menu. TOP PREVIOUS NEXT...
7.8.4 Adjustment Procedure TOP PREVIOUS NEXT 1. Display Input Level Adjustment (RGB) menu. 2. Input a window pattern signal to PC IN (RGB) connector. Note: Use approx. 15 % window pattern as follows. Black background (screen width) : White window width = 2 : 1 Black background (screen height) : White window height = 3 : 1 3.
10 Block Diagram TOP PREVIOUS NEXT 10.1 Power Supply 10.2 Signal Processing (1 / 3) 10.3 Signal Processing (2 / 3) 10.4 Signal Processing (3 / 3) TOP PREVIOUS NEXT...
Page 125
Power Supply COLD +17 V MAIN POWER INTERLOCK TH101 F9101 D9101 SWITCH POWER STB 3.4 V LINE LINE SWITCHING MC202 RECTIFIER FACTOR FILTER FILTERS TRANSFORMER THERMOFUSE Z101 CORRECTION A-P.C.Board FAN 14 V K-P.C.Board +6 V AC IN 3.4 V 3.4 V Ground Lug Q205 SWITCHING...
Page 126
Signal Processing (1/3) from/to (3/3) IC1001 IC1005 IC1006 64M SDRAM TXDRGBIN (x2) RESIZE, IC1008 KEYSTONE CORRECTION, PC IN VIDEO DECODER, INTERLACE/PROGRESSIVE 3ch A/D, TRANSFORMATION, OSDI AI CONTROL, NOISE REDUCTION OSDG RXDRGBIN IC1007 OSDR PLLHS OSDB G/Y-IN VIDEO_V OSDACT RGBHS MCLK YUV_D POCLK Y_SYNC...
Page 129
11.9 B-Module (2 / 2) TOP PREVIOUS NEXT...
Page 130
Signal Processing (3/3) A-P.C.Board YUVHS IC1107 YUVVS Q1108, Q1109 3.3V_SDA HDMI IN 3.3V 3.3V_SCL LEVEL CONVERTER G/Y-IN VIDEO-IN-21PIN AC_SYNC ADAPTER IC1105 VIDEO IN RED IN SCART GREEN IN BLUE IN J-P.C.Board (PT-AE700E only) from/to (1/3)
15 Replacement Parts List TOP PREVIOUS NEXT Ref. No. Part No. Part Name & Description Remarks [MECHANICAL PARTS] D4CDH5030002 TEMP SENSOR DFGB0112ZA-0 PANASONIC BADGE J0KG00000052 CORE K2CG3FR00001 POWER CORD PT-AE700U K2CM3FR00002 POWER CORD(EUROPE) PT-AE700E K2CT3FR00003 POWER CORD(U.K) PT-AE700E K2KA2FA00003 AV CABLE...
Page 153
PBS FAN L6FCLFCH0006 INHALATION FAN N2QAEA000025 REMOTE CONTROLLER TBLB0047 ADJUST LEG TBLG3042 RUBBER LEG TBMA160 LOGO BADGE TBMF685 MODEL NAME PLATE PT-AE700U TBMF686 MODEL NAME PLATE PT-AE700E TBMF688 MODEL NO. LABEL PT-AE700U TBMF689 MODEL NO. LABEL PT-AE700E TBXA44901 CONTROL BUTTOM TEEC0035...