Related Manuals for Ice-O-Matic VRC
Summary of Contents for Ice-O-Matic VRC
- Page 1 INSTALLATION AND PARTS MANUAL REMOTE CONDENSERS MODELS: VRC Ice-O-Matic 11100 East 45th Ave Denver, Colorado 80239 Part Number 9081245-01 Date 3/08...
- Page 3 Introduction How To Use This Manual Ice-O-Matic provides this manual as an aid to the service technician in installation and maintenance of remote condensers. Do not attempt to perform installation, start-up or maintenance unless you have read and fully understand this manual.
-
Page 4: Table Of Contents
Introduction Table of Contents Freight Claim Procedure Warranty General Information Installation Guidelines Remote Refrigeration System Component Description Installation Service Parts VRC Table of Contents Page ii Page i Page ii Page iii Page iv Page 1 Page 2 Page 4... -
Page 5: Freight Claim Procedure
If loss or damage does not appear until merchandise has been unpacked, make a written request for inspection by the carrier within 15 days of the delivery date. Then file a claim on a form from the carrier. File Claim Without Delay Do Not Return Damaged Merchandise to Ice-O-Matic Page iii... -
Page 6: Warranty
Company-authorized distributor, without cost to the Customer, that part of any such machine that becomes defective. In the event that the Warranty Registration Card indicating the installation date has not been returned to Ice-O-Matic, the warranty period will begin on the date of shipment from the Company. -
Page 7: General Information
Verify the ICE machine is compatible with the remote condenser. Some ice machines and some remote condensers may or may not have a Mixing Valve (Head Master). Only one valve is required per system. Kits are available to modify the remote condenser for compatibility. For more information contact your Ice-O-Matic Distributor. General Information Height Compatible With: 38.90... -
Page 8: Installation Guidelines
Remote Condenser Introduction Ice-O-Matic Remote Condenser Systems are comprised of three components. The pre-charged remote condenser, the pre-charged ice maker and the pre-charged line set. The pre-charged line sets are available in 25, 40, 45, 60 or 75 foot line set lengths. The 60 foot line set will require adding an additional 16 ounces of refrigerant to the system. - Page 9 Remote Condenser The VRC remote condensers incorporate the mixing valve in the condenser. This configuration allows up to a 100 foot calculated remote line set run. Reference the diagram below to calculate the maximum 100 foot line set run. Limitations for new remote machines that have the mixing valve mounted in the condenser.
-
Page 10: Remote Refrigeration System
Remote Condenser Remote Refrigeration System The Remote Refrigeration System is shown in the above diagram. During the freezing cycle, high temperature and high pressure liquid refrigerant is directed from the condenser through a mixing valve, receiver, liquid line solenoid heat exchanger and a filter drier. The expansion valve meters refrigerant to the coils on the back of the evaporator. -
Page 11: Component Description
Remote Condenser Component Description Mixing Valve (Headmaster, Low Ambient Control Valve) This valve serves as the head pressure regulating valve. It contains a pre-determined charge of nitrogen in the valve bellows. When the temperature at the condenser is above 70°F (21°C), the refrigerant flow from the compressor is directed by the mixing valve through the condenser and into the receiver. -
Page 12: Installation
3. Make sure the supply voltage is the same as the rated voltage shown on the nameplate. 4. Reference wiring diagram below for proper connections. THE “VRC” SERIES REMOTE CONDENSER MAY ONLY BE USED WITH COMPATIBLE ICE-O-MATIC ICE MAKERS Electrical shock and/or injury from moving parts inside this machine can cause serious injury. - Page 13 Remote Condenser Support Leg Installation-VRC 1. After removal of the packaging and fasteners, lift the condenser assembly off of the skid. 2. Locate the legs and leg braces attached to the condenser assembly. Cut the wire ties and separate the legs from the condenser.
- Page 14 Remote Condenser Installation Vertical Air Flow Page 8...
- Page 15 Remote Condenser Proper Tubing Routing When installing the discharge and liquid lines from the remote condenser to the icemaker, please use the following guidelines: 1. The remote condenser (#2) should always be installed above the icemaker (#4) as shown with a vertical air flow on page 8.
-
Page 16: Service Parts Vrc
Remote Condenser Item Description VRC1001 Fan Guard 9131452-01 Top Panel 3013222-01 ¼-20 x 1/2 Screw 9031019-04 Fan Blade 9131451-01 Fan Motor 9161117-02 ¼-20 x ¾ Cap Screw 9031001-02 Flat Washer 9031003-01 Flanged Lock Nut 9031118-02 ¼-20 x 1/2 Screw 9031019-04 10 Rear Panel 3013224-01 11 Brace... - Page 17 Remote Condenser Service Parts Page 11...