Fuels - Makita DCS4600S Instruction Manual

Fuel
CAUTION:
This saw is powered by mineral-oil products (gasoline and
oil).
Be especially careful when handling gasoline .
Avoid all flame or fire. Do not smoke (explosion hazard).
Fuel mixture
The engine of the chain saw is a high-efficiency two-stroke
engine. It runs on a mixture of gasoline and two-stroke engine
oil.
The engine is designed for unleaded regular gasoline with a
min. octane value of 91 ROZ. In case no such fuel is available,
you can use fuel with a higher octane value. This will not affect
the engine.
In order to obtain an optimum engine output and to protect
your health and the environment use unleaded fuel only.
For lubricating the engine use a two-stroke engine oil (quality
grade: JASO FC or ISO EGD), which is added to the fuel. The
engine has been designed for use of MAKITA high-perform-
ance two-stroke engine oil and a mixture ratio of only 50:1 to
protect the environment. In addition, a long service life and
reliable operation with a minimum emission of exhaust gases
are ensured. MAKITA high-performance two-stroke engine oil
is available in the following sizes to suit your individual require-
ments:
1 l order number 980 008 607
100 ml order number 980 008 606
In case MAKITA high-performance two-stroke engine oil is not
available, it is urgently recommended to use a mixture ratio of
40:1 with other two-stroke engine oils, as otherwise optimum
operation of the engine cannot be guaranteed.
Caution: Do not use ready-mixed fuel from petrol
stations.
The correct mixture ratio:
50:1 when using MAKITA high-performance two-stroke en-
gine oil, i. e. mix 50 parts gasoline with 1 part oil.
40:1 when using other two-stroke engine oils, i. e. mix 40
parts gasoline with 1 part oil.
NOTE:
For preparing the fuel-oil mixture first mix the entire oil quantity
with half of the fuel required, then add the remaining fuel.
Thoroughly shake the mixture before filling it into the chain saw
tank.
Chain oil
Use an oil with adhesive additive for lubricating the chain and
guide bar. The adhesive additive prevents the oil from being
flung off the chain too quickly.
We recommend the use of chain oil which is bio-degradable in
order to protect the environment. The use of bio-degradable oil
may even be required by local regulations.
The chain oil BIOTOP sold by MAKITA is made of special
vegetable oils and is 100% bio-degradable. BIOTOP has been
granted the "blue angel" (Blauer Umweltschutz-Engel) for
being particularly environment-friendly (RAL UZ 48).
Gasoline
+
1000 cm 3 (1 litre)
5000 cm 3 (5 litres)
10000 cm 3 (10 litres)
It is not wise to add more engine oil than specified
to ensure safe operation. This will only result in a
higher production of combus-tion residues which
will pollute the environment and clog the exhaust
channel in the cylinder as well as the muffler. In
addition, fuel consumption will rise and perform-
ance will decrease.
The Storage of Fuel
Fuels have a limited storage life. Fuel and fuel
mixtures age. Therefore fuel and fuel mixtures, which
have been stored for too long, can cause starting
problems. Purchase only that amount of fuel, which
will be consumed over the next few months.
Store fuel safely in a dry place in approved
containers only.
AVOID SKIN AND EYE CONTACT
Mineral oil products degrease your skin. If your skin
comes in contact with these substances repeatedly
and for an extended period of time, it will desiccate.
Various skin deseases may result. In addition, allergic
reactions are known to occur.
Eyes can be irritated by contact with oil. If oil comes
into your eyes, immediately wash them with clear
water.
If your eyes are still irritated, see a doctor immedi-
ately!
BIOTOP chain oil is available in the following sizes:
1 l order number 980 008 610
5 l order number 980 008 611
Bio-degradable oil is stable only for a limited period of
time. It should be used within 2 years from the date of
manufacture (printed on the container).
50:1
40:1
OIL OIL
50:1
20 cm 3 25 cm 3
100 cm 3 125 cm 3
200 cm 3 250 cm 3
D
E
13