1. Precautions and Safety Notices Precautions and safety notices 1.1 safety precautions This monitor is manufactured and tested on a ground principle that a user’s safety comes first. However, improper use or installation may cause damage to the monitor as well as the user. Carefully go over the following WARNINGS before installing and keep this guide handy.
Page 5
Correct Methods Incorrect Methods Only touch the metal-frame of the panel or the Surface of the panel is pressed by fingers and that may cause “ MURA “ front cover of the monitor. Do not touch the surface of the polarizer. Take out the monitor from carton.
Portuguese, Russian, Turkish, French, Czech, ViewSonic CD Wizard Hungarian, Simplified Chinese, Traditional Chinese. Greek, Dutch, Bulgarian, Croatian, Romanian, Serbian, Slovak, Slovenian ViewSonic Quick Start Guide One Page Perfect Suite CD Screen Protector Mylar Foot Protector plastic Base assembly Procedure Card...
Page 7
2.2 Interface description Video Connector Pin Assignment A -1.15 pin D-sub connector pin assignment Pin Number Pin Function Red video input Green video input Blue video input No Connection Ground Red video ground Green video ground Blue video ground H/V sync ground No connection (SDA) Horizontal sync (Composite sync)
3. Front Panel Function Control Description Use the buttons on the front control panel to display and adjust the OSD controls which display on the screen. The OSD controls are explained at the top of the next page and are defined in “Main Menu Controls”...
Page 9
Do the following to adjust the display setting: 1. To display the Main Menu, press button [1]. NOTE: All OSD menus and adjustment screens disappear automatically after about 15 seconds. This is adjustable through the OSD timeout setting in the setup menu. 2.
Page 10
Main Menu Controls Adjust the menu items shown below by using the up and down buttons. Control Explanation Auto Image Adjust automatically sizes, centers, and fine tunes the video signal to eliminate waviness and distortion. Press the [2] button to obtain a sharper image.
Page 11
Information displays the timing mode (video signal input) coming from the graphics card in the computer, the LCD model number, the serial number, and the ViewSonic® website URL. See your graphics card’s user guide for instructions on changing the resolution and refresh rate (vertical frequency).
Page 12
Control Explanation Setup Menu displays the menu shown below: Language Select allows the user to choose the language used in the menus and control screens. Resolution Notice advises the optimal resolution to use. OSD Position allows the user to move the OSD menus and control screens. OSD Timeout sets the length of time the OSD screen is displayed.
Page 14
5. Adjustment Procedure 1. All Modes Reset You should do “All Model Reset” (Refer to Chap 3. Hot Keys for Function Controls) first. This action will allow you to erase all end-user’s settings and restore the factory defaults. 2. Auto Image Adjust The Auto Adjust is aimed to offer a best screen quality by built-in ASIC.
Page 15
7. 25 Gray Test Signal: 1280*1024@60Hz Test Pattern: Full Screen 25% White (Gray) Inspection Item: Particle, Line Defect & Mura 8. 50 Gray Test Signal: 1280*1024@60Hz Test Pattern: Full Screen 50% White (Gray) Inspection Item: Bright Dot, Particle, Line Defect & Mura 9.
Page 16
12. Green Test Signal: 1280*1024@60Hz Test Pattern: Full Screen Green Inspection Item: Bright Dot, Partial & Line Defect 13. Blue Test Signal: 1280*1024@60Hz Test Pattern: Full Screen Green Inspection Item: Bright Dot, Partial & Line Defect 14. Gray_Scale_0-100_V64 Test Signal: 1280*1024@60Hz Test Pattern: Vertical 64 (256) Gray Scale (Right →...
Page 18
Figure 7 Figure 8 Factory Defaults Item Defaults Item Defaults Contrast Input Priority Brightness 100% Resolution Notice Color Temperature 6500K Volume 100% Sharpness Balance OSD H. Position Treble OSD V. Position Bass OSD Time Out 720x400 / 640x400 720x400 OSD Background ECO Mode Standard Aspect Ratio...
Page 19
Step 1. Update BIOS Flow: Execute ISP.exe Step2. Click【64K】, Select the first file name xxxxxxxxxx_1.hex and Click【64~96】, Select the second file name xxxxxxxx_2.hex Step 3. Select【Both】and 【Auto】.
Page 20
then appear below condition. Step 4. Click...
6. Troubleshooting Flow Chart Troubleshooting No power Make sure power button (or switch)is ON. Make sure A/C power cord is securely connected to the LCD display. Plug another electrical device (like a radio)into the power outlet to verify that the outlet is supplying proper voltage.
8. Schematic Diagrams 8.1 main board 8.2 power board...
Page 24
Main board GN D _POWER R I+ OPEN /U DZSF-5.6B/RoH S OPEN /BAV99/R oH S R I+ VGA_SD A GND _POWER VGA_SD A HSIN OPEN /0402/100n/16V/Y VSIN VGA_SCL VGA_SC L GN D_POW ER C N1 MLX89263-6762/R oH S OPEN /U D ZSF-5.6B/R oHS OPEN /U DZSF-5.6B/RoH S GN D _POWER OPEN/U D ZSF-5.6B/R oHS...
Page 44
065G0402104 17 CAP CHIP 0402 100nF Z 16V Y5V 065G0402104 17 CAP CHIP 0402 100nF Z 16V Y5V 065G0402104 17 CAP CHIP 0402 100nF Z 16V Y5V 065G0402104 17 CAP CHIP 0402 100nF Z 16V Y5V 065G0402104 17 CAP CHIP 0402 100nF Z 16V Y5V 065G0402120 31 CAP CHIP 0402 12P 50V NPO 065G0402220 31...
Page 45
033G8019 2CMO CONN.25-D000187 077G 606501 CJ TACT SWITCH 077G 606501 CJ TACT SWITCH 077G 606501 CJ TACT SWITCH 077G 606501 CJ TACT SWITCH 077G 606501 CJ TACT SWITCH 081G 63O 1 GP LED GPTS0603OC3-PB 081G0603 B GP LED GPTS06033BC1 GP 715G3032 1 KEY PCB FR-4 76x11.8x1.0mm DS 033G8019 2JCMO...
Page 63
065G0402104 17 CAP CHIP 0402 100nF Z 16V Y5V 065G0402120 31 CAP CHIP 0402 12P 50V NPO 065G0402220 31 CHIP 22PF 50V NPO 065G0402220 31 CHIP 22PF 50V NPO 065G0402220 31 CHIP 22PF 50V NPO 065G0402473 17 CAP CHIP 0402 47nF K 16V Y5V 065G0402473 17 CAP CHIP 0402 47nF K 16V Y5V 065G0402473 17...
Page 64
077G 606501 CJ TACT SWITCH 077G 606501 CJ TACT SWITCH 081G 63O 1 GP LED GPTS0603OC3-PB 081G0603 B GP LED GPTS06033BC1 GP 715G3032 1 KEY PCB FR-4 76x11.8x1.0mm DS 033G8019 2JCMO CONNECTOR 1.0pitch SMT 15p...
12. Different parts list Diversity of T96MRYDDIWVWNND compared with T96MRYDBIWVSNNN Location Part No. Description Remark N40G000196868A S/N LABEL N40G0001968 2A S/N LABEL 7741513161 N44G9007968 2A CARTON FOR China- 78-D018443 F40G 19N96839A SAFETY LABEL N34G0091 ZK 1B REAR 40-D018254 POWER CORD(32E1818021)(中規) 089G414A18N YH POWER CORD 32E1818021(与...
Page 66
N40G000296821A ZA Supplier label N40G000296811C ZA Customer label on Carton N41G780P968 1A WARRANTY CARD- 78-D021250...
Page 67
Reader’s basic dada: Name: Title: Company: Add: Tel: Fax: E-mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com)