Table of Contents
Advertisement
RoHS Statement
The following chart is provided for product use in China.
部件名称
(Part Name)
电路板组件
(PCB Assemblies)
机壳装配件
(Chassis Assemblies)
O: 表明这些有毒或有害物质在部件使用的同类材料中的含量是在 SJ/T11363_2006极限的要求之下。
O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/
T11363-2006.
X: 表明这些有毒或有害物质在部件使用的同类材料中至少有一种而含量是在SJ/T11363_2006极限的要求之上。
X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit
requirement in SJ/T11363-2006.
Unpacking
There are no special unpacking precautions. However, it is recommended that you keep the original packing materials for reuse in the rare event that
service is required. If service is required and the original packing material is not available, ensure that the unit is adequately protected for shipment
(use a strong box of appropriate size, suffi cient packing/padding material to prevent load shifting or impact damage) or call QSC's Technical Services
Group for replacement packing material and a carton.
What is included in your Q-Sys™ product carton:
Q-Sys Core 250i or Core 500i
• Rubber feet
• Q-Sys Hardware User Manual
• Q-Sys Designer software CD
• IEC power cord and cord lock wire
• Connector plug kit appropriate for the optional Q-Sys Audio I/O Card(s) ordered
Mounting
Q-Sys products can be used in or out of an equipment rack. Rack mounting is optional. Adhesive rubber feet are included for non-rack mount
installations (table or shelf top installations). Use the feet to prevent the unit from scratching or marring the support surface.
Rack Mount Instructions
Rack mount the Q-Sys product by supporting it from underneath while aligning the front panel mounting holes (in the rack ears) with the threaded
screw holes in the rack rails. Install all four mounting screws and washers and tighten securely. All Q-Sys products come with rear rack support ears.
Ensure that these rear mounting points are securely fastened to rear rack rails or side walls.
WARNING!: Reliable Earthing — Reliable earthing of rack-mounted equipment should be maintained. Particular attention
should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
Mechanical Loading — Mounting the equipment in the rack should be done such that a hazardous condition is not achieved due
to uneven or unstable mechanical loading.
CAUTION!: Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the ambient operating temperature of
the rack environment may be greater than room ambient. Consideration should be given to ensure that the maximum operating
temperature listed in
Reduced Air Flow — Installation of the equipment in a rack should be such that the amount of air fl ow required for safe operation of
the equipment is not compromised.
Circuit Overloading — Consideration should be given to the connection of the equipment to the supply circuit and the effect that
overloading of the circuits might have on over-current protection and supply wiring.
TD-000347-00-B
(Toxic or hazardous Substances and Elements )
铅
汞
(Pb)
(Hg)
X
O
X
O
"Q-Sys Type 2 System Hardware Specifi cations" on page 15
Q-Sys™ Core 250i 系列, Q-Sys Core 500i
有毒有害物质或元素
镉
六价铬
(Cd)
(Cr(vi))
O
O
X
O
is not exceeded.
4
多溴联苯
多溴二苯醚
(PBB)
(PBDE)
O
O
O
O
Hide quick links:
Advertisement
Table of Contents
