Friedrich SH15 Installation & Operation Manual
230-volt hazardous duty room air conditioner
Hide thumbs
Also See for SH15:
- User manual (60 pages) ,
- Installation & operation manual (63 pages) ,
- Installation & operation manual (90 pages)
Related Manuals for Friedrich SH15
Summary of Contents for Friedrich SH15
- Page 1 Installation & Operation Manual Hazardous Duty Room Air Conditioner 230-Volt: SH15 | SH20 www.segind.com.br...
-
Page 2: Table Of Contents
Table of Contents Operation and Care Instructions Your Safety and the safety of others........................... 2 General Instructions ................................3 Filter information ................................4 Maintenance Checklist................................ 4 Special Features .................................. 5 Control Panel ..................................5 Underwriters Laboratories ..............................5 Installation Instructions Electrical Requirements .............................. -
Page 3: General Instructions
General Instructions Your new Friedrich has been carefully engineered and manufactured to give you many years of dependable, efficient operation, main- taining a comfortable temperature and humidity level. Many extra features have been built into your unit to assure quiet operation, the greatest circulation of cool, dry air, and the most economic operation. -
Page 4: Filter Information
Cleaning If the unit does not operate at all, check that the power supply The front grille of your Friedrich, as well as the complete cabi- connections are tight. Check for blown fuses or tripped circuit net may be cleaned with warm water and a mild detergent. The breakers. -
Page 5: Special Features
Electrodeposited epoxy primer and alkyd enamel, both oven-baked for an attractive, long-lasting finish. Friedrich Air Conditioning quality has been proven by more than 25 years of successful experience from the Gulf of Mexico to the searing sands of the Arabian desert. -
Page 6: Installation Instructions
Installation Instructions Models SH15 and SH20 NOTE: THIS MANUAL INCLUDES INSTALLATION INSTRUCTIONS FOR BOTH WINDOW MOUNT AND THROUGH- THE-WALL INSTALLATIONS WARNING Explosion Hazard Electrical Shock Hazard Electrically connect unit in accordance with NEC Code Article 501. Failure to do so can result in death, explosion, fire, or electrical shock. - Page 7 Hazardgard Window Mount Installation Hardware ITEM DESCRIPTION QTY. SHELL MOUNTING PARTS SCREW, 10 - 24 x 1" HEX HEAD SCREW, SHEET METAL #12A x 2" WINGBOARD ANGLE MOUNTING WINGBOARD ANGLE, TOP WINGBOARD ANGLE, SIDE SCREW, SHEET METAL #8A x 3/8" WINGBOARD MOUNTING PARTS WINGBOARD (MASONITE) - ITEM # 3...
-
Page 8: Unpacking The Unit
Be sure that the shell can fit between this box and the chassis. PROVIDED HARDWARE 1 JUNCTION BOX FRIEDRICH PN: 613-893-00 2 MOUNTING LEGS RACO INC. PN: 5324-0 2 LEG SCREWS... -
Page 9: Shell Preparation
Shell (Cabinet) Preparation each end of the top angle (Item #5) with the top loops of the side It will be necessary to relocate the sill plate of the cabinet 2" angle. Install two (2) screws (Item #7) to secure the top angle back from its shipping position, and the shell guides 4"... -
Page 10: Shell Installation
Shell Installation: Sash Window Installations WARNING Falling Object Hazard Not following Installation Instructions for mounting your air conditioner can result in property damage, injury, or death. Shell (Cabinet) Installation – Standard Sash Windows STEP 1 Check the window sill and frame to be sure they are in good condition and firmly anchored to the wall. Repair if necessary. - Page 11 The illustrations below show a standard frame construction NOTICE installation as well as some suggested ways of adapting the support bracket to thick walls and large stone ledges. Instructions for mounting sleeve with slope must be observed to prevent entry of water into room.
- Page 12 "J" TYPE SPEED NUT (ITEM #9) Figure G 2 REQUIRED SPRING STEEL CLIP (ITEM #10) 2 REQUIRED CUT WINGBOARD PANEL CUT EDGE SLIDE CLIP OVER CUT EDGE OF WINGBOARD PANEL CENTER THE HOLE IN THE SPEED NUT OVER THE SLOT IN THE WINGBOARD PANEL S TEP 5 ASSEMBLE CLIPS TO WINGBOARD PANELS: Assemble "J"...
- Page 13 Shell Installation: Through-the-wall Installations WARNING Falling Object Hazard Not following Installation Instructions for mounting your air conditioner can result in property damage, injury, or death. Wall Preparation The maximum wall thickness permissible without special construction is determined by the model size to be installed. THE OUT- SIDE CABINET CONDENSER AIR INTAKE LOUVERS MUST NOT BE BLOCKED BY EXTENDING INSIDE THE WALL AREA.
- Page 14 Figure L FRAME WALL CONSTRUCTION CAULK ALL SIDES WEATHER CABINET SHIM THE VOID SPACE AT THE TOP AND SIDES WITH WOOD AS REQUIRED Figure M BRICK VENEER WEATHER CABINET CONSTRUCTION CAULK ALL SIDES SHIM VOID SPACES AT TOP AND SIDES WITH WOOD AS REQUIRED Figure N SOLID MASONRY CONSTRUCTION...
-
Page 15: Through-The-Wall
STEP 3 Slide the cabinet into the hole far enough to allow the guide-channel of the sill plate to contact the inside wall surface (See Figure O). STEP 4 Drill three (3) 5/32" dia. pilot holes through holes in sill-plate into the framing and install three (3) #12 x 2" long screws (Item #4) (See Figure O). -
Page 16: Chassis Installation
Chassis Installation STEP 1 Slide the chassis into the cabinet stopping approximately 3" from full insertion. Stuff the chassis seal gasket (Item #14) one inch deep between the chassis and the cabinet (See Figure P). Begin at either bottom corner and go up the side, across the top, and down the opposite side. - Page 17 STEP 2 Be sure that the filter is in place then install the return air grille (See Figure Q). The top of the return air grille can be butted against the bottom of the discharge plenum. Snap the grille into place by pushing the grille up and onto the unit's latches at the bottom.
-
Page 18: Warranty
LIMITED ONE YEAR PARTS WARRANTY 1. Limited warranty – One year. Friedrich warrants that it will provide a replacement for any part of this HazardGard Room Air Conditioner found defective in material or workmanship for a period of one (1) year from the date of original purchase.