SAFETY PRECAUTIONS IMPORTANT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent Shock, Fire, or other Hazards.
SERVICING PRECAUTIONS CAUTION: Before servicing receivers covered by this service unit under test. manual and its supplements and addenda, read and follow the 2. After removing an electrical assembly equipped with ES SAFETY PRECAUTIONS on page 3 of this publication. devices, place the assembly on a conductive surface such as NOTE: If unforeseen circumstances create conflict between the aluminum foil, to prevent electrostatic charge buildup or...
Page 5
IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through Circuit Board Foil Repair which the IC leads are inserted and then bent flat against the Excessive heat applied to the copper foil of any printed circuit circuit foil. When holes are the slotted type, the following technique board will weaken the adhesive that bonds the foil to the circuit should be used to remove and replace the IC.
Screen Size 26 inch Wide – 26 inches(582.96mm) For 26LC7D-UB 32 inch Wide - 31.51inches(800.4mm) For 32LC7D-UB,32LC4D-UA 37 inch Wide – 32.02 inches(940.3mm) For 37LC7D-UB 42 inch Wide – 42.02 inches(1067.308mm) For 42LC7D-UB,42LC4D-UA Aspect Ratio 16:9 Tuning System LCD Module...
Page 7
5. Chroma & Brightness 5-1. 37LC7D-UB CONDITION : EZ-Picture "Daylight" Item Unit Remark White peak brightness cd/m HDMI input, full white, Video Black level=High Contrast ratio 700:1 900:1 Non dimming mode (PC Mode) 3000:1 4000:1 5000:1 Dimming mode 1. Input full black, wait 10 minute, measure black level 2.
Page 9
8. Mechanical specification 1) 37LC7D Item Content Unit Remark Product Widt(W) Length(D) Height(H) Dimension Before Packing 280.5 692.8 With Stant After Packing Product Only SET With BOX 2) 42LC7D Item Content Unit Remark Product Widt(W) Length(D) Height(H) Dimension Before Packing 1033.4...
Page 10
9. Customer Menu Setup (Shipment Condition) Item Condition Remark Input Mode TV02CH Volume Level Mute Aspect Ratio 16:9 Video EZ Picture Daylight Contrast Brightness Color Sharpness Tint Color-temperature Cool Auto(On) Advanced Cinema3:2 Mode(Off) Black Level(RF,HDMI=>Low),(AV=>High)( RGB-PC,Component=>Disable) Audio Audio Language EZ Sound Normal Balance Bass...
ADJUSTMENT INSTRUCTION 1. Application Object 3. MICOM Download(Option) These instructions are applied to all of the LCD TV, LA73E. 3-1. Required Test Equipment (1) JIG-LEVER TYPE for adjusting: 1EA (2) PC & MONITOR: 2EA 2. Notes (3) BOARD for INTERFACE: IIC & ISP BOARD: 2EA (1) Because this is not a hot chassis, it is not necessary to use (4) 15P D-SUB CABLE: 2EA an isolation transformer.
Page 12
(3) Click the first icon shown in fig.9. The window seen in (3) Click the Send. fig.10 should appear. 3-4. Set Method (1) MCU Select: MTV512M64 (2) Option R/W Option: Auto Write(Verity) (4) When you see (ISP COMPLETE) the download is Jig Option: Myson complete.
Page 13
6-3. Adjustment 6. ADC-Set Adjustment (1) Select Component1 as the input with 100% Horizontal 6-1. Synopsis Color Bar Pattern(HozTV31Bar) in 480i Mode (2) After receiving signal for at least 1 second, press the ADJ ADC-Set adjustment to set the black level and the Gain to Key on the Service R/C to enter the ‘Ez - Adjust’...
Page 14
7-2. EDID DATA for LA73E 7. EDID(The Extended Display Identification Data)/DDC EDID for HDMI-1 (DDC (Display Data Channel) Data) (Display Data Channel) Download EDID Block 0 table = 0 | 00 FF FF FF FF FF FF 00 1E 6D 01 00 01 01 01 01 This is the function that enables “Plug and Play".
Page 15
8. Adjustment of White Balance [ Requirements for Automatic Adjustment 8-1. The Purpose and Principal of Color (1) The illuminance of surroundings 10 lux or less; preventing light in surroundings as much as Temperature Adjustment possible (1) Purpose: to reduce the difference in color temperature (2) The location of the Probe among modules 1) For PDP: place the color analyzer (CA-110, CA-210)
Page 16
[ [ RS-232C Command 9. USB S/W Download (Option) (Automatic Adjustment) LA73E Chassis Model All] 9-1. Overview USB Download enables quick response to S/W upgrading RS-232C COMMAND CENTER and helps to configure the panel to the latest updates. [CMD ID DATA] (DEFAULT)(Decimal) (Deci 9-2.