Boyo AVN700A Instruction Manual page 129

Installation & Functions
WARNING
- Do not connect the ignition wire and the battery wire to the car chassis(ground) ,you may cause a short circuit, that in turn
may start a fire. Always connect those wires to the power source running through the fuse box.
- Do not cut out the fuse from the ignition wire and the battery wire.
The power supply must be connected to the wires via the fuse.
CAUTION
-If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on
and off with the ignition key.
-If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may
die.
-If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening
-If the fuse blows, first make sure the wires aren't touching to cause a short circuit, then replace the old fuse with one with
the same rating.
-Insulate unconnected wires with vinyl tape or other similar material. To prevent al short circuit, do not remove the caps on
the ends of the unconnected wires or the terminals.
- Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if
you share the "-" wires or ground them to any metal part in the car.
- When only two speakers are being connected to the system. Connect the connectors either to both the front output
terminals or to both the rear output terminals (do mot mix front and rear).
- For example, if you connect the "+" connector of the left speaker to a front ouput terminal, do not connect the - connector
to a rear ouput terminal.
- After the unit is installed, check wheather the brake lamps, blinkers, wipers, etc. on the car are working properly.
- Mount the unit so that the mounting angle is 30' or less.
How to install
I ''I
Boon:!
t_~
01
Unpack the GIFT BOX.
Screw
Ha~
Sleeve
02
Detach the unit from the Half Sleeve.
03
Remove the safety screw for
Transporting which is on the top of
the unit.
Transporting which
IS
on the top of
t~e
unit
• Remove the protection unit
(support panel)
(Sticker "You must remove it before
you Install" )
Half Sleeve
04
Front dash board
05
Source the half sleeve by
bending the metal Tabs. downward
Board
06
Insert the into Dash Board.
07
Install the set and then install the
Trim Plate (option).
Installation & Functions
WARNING
- Do not connect the ignition wire and the battery wire to the car chassis(ground) ,you may cause a short circuit, that in turn
may start a fire. Always connect those wires to the power source running through the fuse box.
- Do not cut out the fuse from the ignition wire and the battery wire.
The power supply must be connected to the wires via the fuse.
CAUTION
-If your car's ignition does not have an ACC position, connect the ignition wires to a power source that can be turned on
and off with the ignition key.
-If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may
die.
-If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening
-If the fuse blows, first make sure the wires aren't touching to cause a short circuit, then replace the old fuse with one with
the same rating.
-Insulate unconnected wires with vinyl tape or other similar material. To prevent al short circuit, do not remove the caps on
the ends of the unconnected wires or the terminals.
- Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if
you share the "-" wires or ground them to any metal part in the car.
- When only two speakers are being connected to the system. Connect the connectors either to both the front output
terminals or to both the rear output terminals (do mot mix front and rear).
- For example, if you connect the "+" connector of the left speaker to a front ouput terminal, do not connect the - connector
to a rear ouput terminal.
- After the unit is installed, check wheather the brake lamps, blinkers, wipers, etc. on the car are working properly.
- Mount the unit so that the mounting angle is 30' or less.
How to install
I ''I
Boon:!
t_~
01
Unpack the GIFT BOX.
Screw
Ha~
Sleeve
02
Detach the unit from the Half Sleeve.
03
Remove the safety screw for
Transporting which is on the top of
the unit.
Transporting which
IS
on the top of
t~e
unit
• Remove the protection unit
(support panel)
(Sticker "You must remove it before
you Install" )
Half Sleeve
04
Front dash board
05
Source the half sleeve by
bending the metal Tabs. downward
Board
06
Insert the into Dash Board.
07
Install the set and then install the
Trim Plate (option).