1. Manuals
  2. Brands
  3. UTStarcom Manuals
  4. Modem
  5. UT-300R2U
  6. User manual

UTStarcom UT-300R2U User Manual

Hide thumbs Also See for UT-300R2U:
Table of Contents

Advertisement

Quick Links

UTStarcom UT-300R2U
ADSL Modem
USER GUIDE
Release: 1.0
Doc. Code:
UTStarcom, Inc.

Advertisement

Table of Contents
loading

Related Manuals for UTStarcom UT-300R2U

Summary of Contents for UTStarcom UT-300R2U

  • Page 1 UTStarcom UT-300R2U ADSL Modem USER GUIDE Release: 1.0 Doc. Code: UTStarcom, Inc.
  • Page 2 UTStarcom, Inc. UTStarcom, Inc. reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of UTStarcom, Inc. to provide notification of such revision or changes.

  • Page 5: Table Of Contents

    Contents ......................1 Features ......................1 Supporting Protocol ..................2 System Requirement ..................3 LED Indicator ....................4 Rear Pane Layout ..................5 ......................6 ......................8 Configuring Computer Network Card IP Address ........... 8 Web Setting Interface ..................8 Ethernet over ATM (RFC1483 Bridge) Setting ..........
  • Page 6 ....................... 28...

  • Page 7: Features

    Introduction This device is a well-designed high-speed ADSL modem/router Features • One 10/100 Ethernet port • One USB 1.1 Full Speed port • Friendly GUI for web configuration • Configurable as a DHCP Server on your Network • Compatible with virtually all standard Internet applications •...

  • Page 8: Supporting Protocol

    Introduction • Support for up to 8 Permanent Virtual Circuits (PVC) • Support for up to 8 PPPOE sessions Supporting Protocol • ITU G.992.1 (G.dmt) Annex A • ITU G.992.2 (G.lite) • ANSI T1.413 Issue 2 • ITU G.992.3 ADSL2 (G.dmt) •...

  • Page 9: System Requirement

    Introduction System Requirement Recommended system requirements are: • Pentium 233MHz or above • Memory: 64MB or above • 10M Base-T Ethernet or above • WIN9X WIN2000 WINXP WINME WINNT • Ethernet Network Interface Card Please collect the following information from your ADSL service provider.

  • Page 10: Led Indicator

    Introduction LED Indicator Indicator Status Description Power not supplied Power supply is on Have linked to HUB Be transmitting data Blink to HUB Have connected to CO physical layer Be trying to connect LINK Slow Blink to physical link Be handing with CO Quick Blink physical link Be receiving and...

  • Page 11: Rear Pane Layout

    Introduction Rear Pane Layout Interface Function SWITCH POWER on/off POWER socket PLUG in for power Modem Reset button. Press three times, hardware will reset, modem LED will be all RESET on, then off, then auto-restart and recover the default configuration. Plug in for RJ45, Can connect to HUB or computer USB port can connect to PC...

  • Page 12: Hardware Installation

    Hardware Installation Please connect your ADSL MODEM to computer as the following description: • If connecting to the splitter, connect the “Line” splitter to wall jack using one telephone cable. • Use the other telephone cable to connect MODEM port of the splitter and LINE port of the modem.
  • Page 13 Hardware Installation If do not need to connect to the splitter, • Connect the modem to wall jack using one telephone cable. • Use Ethernet cable to connect LAN port of the modem and LAN port of your computer.

  • Page 14: Configuring Computer Network Card Ip Address

    Modem Parameters Setting Configuring Computer Network Card IP Address Configuring your network card’s TCP/IP properties to obtain an IP address automatically from modem, or set the computer’s IP with the same network mask of the modem. (For example: modem’s IP is 192.168.1.1/255.255.255.0, then you can set computer’s IP to: 192.168.1.x/255.255.255.0, the range for x is from 3 to 255) Web Setting Interface...
  • Page 15 Modem Parameters Setting Default setting: IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0 Username: admin Password: utstar or admin Main interface When correct username and password have been typed, the following window will pop up:...
  • Page 16 Modem Parameters Setting Here provide the most common configuration for PPPoE and Bridge mode for reference. The CPE shall be configured as following (Advanced Setup – WAN) for MTNL network...

  • Page 17: Ppp Over Ethernet (Rfc2516) Pppoe Setting

    Modem Parameters Setting PPP over Ethernet (RFC2516) PPPoE Setting PPPoE is also known as RFC 2516. It is a method of encapsulating PPP packets over Ethernet. PPP or Point-to- Point protocol is a method of establishing a network connection/session between network hosts. It usually provides a mechanism of authenticating users.
  • Page 18 Modem Parameters Setting Click on Edit button having VPI/VCI = 32, Check the following options: VPI = 0 VCI = 32 Service category “UBR without PCR”...
  • Page 19 Modem Parameters Setting 2. Click the “Next” button , select the type of network protocol and encapsulation mode over the ATM PVC that your ISP has instructed you to use, see the following:...
  • Page 20 Modem Parameters Setting 3. Select PPP over Ethernet (PPPoE), Click the “Next” button.
  • Page 21 Modem Parameters Setting 4. Type the username password given by the MTNL Type service name as MTNL . It is optional you can leave it as blank also. Authentication method “AUTO” Click on next Following window will come. 8. Enable IGMP Multicast, and enable WAN Service, see the following.
  • Page 22 Modem Parameters Setting 8. Click the “Next” button, configure the DSL Router IP Address and Subnet Mask for LAN interface, please use the default configurations, and see the following.
  • Page 23 Modem Parameters Setting 9. Click the “Next” button; make sure that the settings below match the settings provided by your ISP. See the following:...
  • Page 24 Modem Parameters Setting 10. Click on the “Save/Reboot” button, save your configurations, and then finish the Setting for PPPoE.

  • Page 25: Ethernet Over Atm (Rfc1483 Bridge) Setting

    Modem Parameters Setting Ethernet over ATM (RFC1483 Bridge) Setting From the Home page, click on “Advanced Setup ->Wan”, see the following. Click on Edit button having VPI/VCI = 0/33, Check the following options: VPI = 0, VCI = 33 Service category “UBR without PCR” Click on next button...
  • Page 26 Modem Parameters Setting Click the “Next” button, and you can set the encapsulation which get from your ADSL service provider, see the following:...
  • Page 27 Modem Parameters Setting Click the “Next” button , select the check box below to enable this WAN service, see the following:...
  • Page 28 Modem Parameters Setting Click the “Next” button, make sure that the settings below match the settings provided by your ISP., see the following: Click on the “Save/Reboot” button, save your configurations. Note: If you select Dial-UP link, after configuring your ADSL MODEM, please install the third-party dial up program to access Internet (For example: Ethernet 300/Ethernet 500/WinPoet).
  • Page 29 USB Software Setup Note: The software setup process for all supported operating systems is described in this section with operating system specific differences noted. The USB ADSL Modem should be connected to your PC prior to installing the software. No other Windows programs should be running on your PC during the software install process.
  • Page 30 USB Software Setup Just click next, new web will be shown below...
  • Page 31 USB Software Setup Select “Search for a suitable driver for my device (recommended)”, then press next button...
  • Page 32 USB Software Setup If you ADSL Modem USB driver is in CD-ROM, please select CD –ROM driver, And If USB driver is other a location, please select Specify a location. Then press next. Windows will search and find the USB driver and automatically install the driver.
  • Page 33 USB Software Setup Wait for a few seconds, below picture will display and you can press the “Finish” button to complete the USB driver installation. When you have completed USB driver, Your PC will add new adapter networks connect .It means you have success install ADSL modem USB driver .You can configure your modem like Ethernet, and connect internet.
  • Page 34 Questions & Answers Question: Why all LED indicators are off? Answer: • Check the connection between the power adaptor and the power socket. • Check the power switch is on or not. Question: Why ACT LED is not lighting? Answer: •...
  • Page 35 Questions & Answers For Hub/Switch, you should use straight through cable. Question: Why Link LED is not lighting? Answer: Check the connection between the ADSL LINE port and the wall jack. Question: Why cannot visit Internet with Link LED is Answer: Make sure following information has been input correctly: VPI/VCI...
  • Page 36 Questions & Answers Click start -> run (input ping demands) -> Ping 192.168.1.1 (MODEM IP ADDRESS). If cannot reach the modem, please check following configuration: • The type of the network cable • The connection between the modem and computer •...
  • Page 37 UTStarcom, Inc. USA 1275 Harbor Bay Parkway Alameda, CA 94502, USA Tel: 510-864-8800 Fax: 510-864-8802 http://www.utstar.com...

Table of Contents