Husqvarna 325HDA55 x-series, 325HE3, 325HE3 x-series, 325HE4 x-series Operator's Manual
Husqvarna hedge trimmer operator's manual
Hide thumbs
Also See for 325HDA55 x-series, 325HE3, 325HE3 x-series, 325HE4 x-series:
- Operator's manual (28 pages) ,
- Operator's manual (22 pages) ,
- Operator's manual (23 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Advertisement
Table of Contents
Related Manuals for Husqvarna 325HDA55 x-series, 325HE3, 325HE3 x-series, 325HE4 x-series
Summary of Contents for Husqvarna 325HDA55 x-series, 325HE3, 325HE3 x-series, 325HE4 x-series
- Page 1 Operator ′ s manual 325HDA55 323HE3 X-series 325HE3 325HE4 X-series X-series Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h understand the instructions before using the machine.
-
Page 2: Key To Symbols
Symbols WARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 3: Table Of Contents
WARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 4: Introduction
Dear Customer, Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. -
Page 5: What Is What
What is what? 1 Cutter 2 Grease nipples (3) 3 Bevel gear 4 Blade guard (325HDA55) 5 Shaft 6 Front handle (325HDA55, 323HE3, 325HE3) 7 Front handle (325HE4) 8 Throttle control 9 Stop switch 10 Throttle lock 11 Harness support hook (325HE4) 12 Cylinder cover 13 Starter handle 14 Fuel tank... -
Page 6: General Safety Precautions
Personal protective equipment IMPORTANT! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 7: Machine ' S Safety Equipment
See instructions under the heading Start. Start the hedge trimmer and apply full throttle. Release the throttle trigger and check that the blades stop and remain stationary. If the blades move when the throttle trigger is in the idle position then the carburettor idle setting must be adjusted. - Page 8 GENERAL SAFETY PRECAUTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier. The machine ′ s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine ′...
-
Page 9: Gear Housing
GENERAL SAFETY PRECAUTIONS WARNING! Bear in mind that: Engine exhaust fumes contain carbon monoxide, which can cause carbon monoxide poisoning. For this reason you should not start or run the machine indoors, or anywhere that is poorly ventilated. The exhaust fumes from the engine are hot and may contain sparks which can start a fire. -
Page 10: Assembly
(323HE3, 325HE3,325HE4) Fit the handle using two screws. Fitting the cutting head It is important that the hedge trimmer is laid on a flat surface when you fit the cutting head. Otherwise the cutting head may not be fitted straight. -
Page 11: Fuel Handling
When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two- stroke engine oil, which is specially formulated for our air- cooled two-stroke engines. • Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW). -
Page 12: Fuelling
Mixing • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. •... -
Page 13: Starting And Stopping
STARTING AND STOPPING Check before starting • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blades that are dull, cracked or damaged. • Check that the machine is in perfect working order. Check that all nuts and screws are tight. - Page 14 STARTING AND STOPPING Starting Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord.
-
Page 15: Working Techniques
General working instructions IMPORTANT! This section takes up the basic safety precautions for working with a hedge trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. -
Page 16: Basic Working Techniques
Do not rush the work, but work steadily until all the branches have been cut back cleanly. 16 – English WORKING TECHNIQUES Changing the hedge trimmer angle (323HE3, 325HE3,325HE4) • Undo the knob. • Grasp the handle on the angle stop, adjust to the desired angle and then tighten the knob. -
Page 17: Maintenance
Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions... -
Page 18: Muffler
Fine adjustment of the idle speed T Adjust the idle speed with the idle adjustment screw T, if adjustment is necessary. First turn the idle adjustment screw T clockwise until the blades start to move. Then turn the idle adjustment screw T anticlockwise until the blades stop. The idle speed is correctly adjusted when the engine runs smoothly in every position. -
Page 19: Cooling System
See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. -
Page 20: Gear Housing
There are three grease nipples on the gear housing. Use a grease gun to top up with grease. This should be carried out approximately every 20 working hours. Use Husqvarna special grease, part no. 503 98 96-01. CAUTION! The gear housing must not be filled completely with grease. -
Page 21: Maintenance Schedule
Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensive work must be carried out by an authorised service workshop. -
Page 22: Technical Data
Technical data Technical data Engine Cylinder displacement, cm Cylinder bore, mm Stroke, mm Idle speed, rpm Recommended max. speed, rpm Max. speed; should not be exceded, rpm Max. engine output, acc. to ISO 8893 Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug... -
Page 23: Ec-Declaration Of Conformity (Applies To Europe Only)
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge trimmers Husqvarna 325HDA55, 323HE3, 325HE3 and 325HE4 from 2002’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the standards or or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:... - Page 24 1140333-26 ´®z+HA@¶6^¨ ´®z+HA@¶6^¨ 2004-12-28...