Related Manuals for Husqvarna TS200FR
Summary of Contents for Husqvarna TS200FR
- Page 1 8 H.P. 30" (76,2 cm) TILLER ATTACHMENT MODEL NUMBER TS200FR 169689 Rev. 2 4.11.03 TR Printed in U.S.A. OWNER’S MANUAL TS 20 SLEEVE HITCH 02480...
-
Page 2: Safety Rules
• Never operate the machine at high speeds on slippery surfaces. Look behind and use care when backing. • Lift tiller out of the ground when turning corners. • Do not put tractor in reverse gear while tiller is in the ground. • Never allow bystanders near the unit. -
Page 3: Table Of Contents
Please read and retain this manual. The in struc tions will enable you to assemble and main tain your tiller at tach - ment prop erly. Always observe the "SAFETY RULES". -
Page 4: Assembly
NOTE: Remove mower deck from tractor before mounting tiller attachment. • Remove tiller and bag of parts from carton. Place tiller on level ground so that tractor can be backed up to it for assembly. CAUTION: Tiller will be heavy when per form ing the following step. -
Page 5: Operation
Check transmission oil with the tiller leveled on level ground. • Remove oil fi ll plug. Oil should be level with the bottom of tiller plug hole. If necessary add oil until it is level with hole. OPERATION CHECK ENGINE OIL LEVEL (See Fig. 1) The engine on your tiller has been shipped from the fac- tory, already fi... - Page 6 fi eld (garden) or when not tilling. Lift tiller out of the ground when turning corners. Do not put tractor in reverse gear while tiller is in the ground. Before leaving tractor seat, stop tractor, shift tractor to “NEUTRAL”...
-
Page 7: Maintenance Schedule
Tighten oil fi ll plug securely each time you check the oil level. NOTE: It is not necessary to change the oil in tiller trans- mis sion. If for any rea son, it must be changed, ca pac i ty... - Page 8 Change the oil after the fi rst two hours of operation and every 25 hours thereafter or at least once a year if the tiller is not used for 25 hours in one year. Check the crankcase oil level before starting the engine and after each fi...
- Page 9 • Remove blower housing and clean as necessary. • Keep cylinder fi ns free of dirt and chaff. MUFFLER Do not operate tiller without muffl er. Do not tamper with exhaust system. Damaged muffl ers or spark arresters could create a fi re hazard. Inspect periodically and replace if necessary.
-
Page 10: Service And Adjustments
To tighten belt, remove retainer spring securing belt tight en er link to clutch lever and arm. • Standing in front of tiller, turn link in a coun ter clock wise direction one turn at a time, until belt no longer slips. - Page 11 SERVICE AND ADJUSTMENTS ENGINE TO ADJUST CARBURETOR (See Fig. 11) The carburetor has been preset at the factory and ad- just ment should not be necessary. However, minor ad just - ments may be required to com pen sate for differences in fuel, temperature, altitude or load.
-
Page 12: Storage
Immediately prepare your tiller for storage at the end of the season or if the unit will not be used for 30 days or more. CAUTION: Never store the tiller with gasoline in the tank inside a build ing where fumes may reach an open fl ame or spark. -
Page 13: Troubleshooting
Ground too dry and hard. diffi cult handling Soil balls up or clumps Ground too wet. Engine runs but tiller 1. Tine clutch control is not engaged. tines won’t move 2. V-belt not correctly adjusted. 3. V-belt is off pulley(s). -
Page 14: Repair Parts - Tiller
REPAIR PARTS 8 HP TILLER ATTACHMENT - - MODEL NUMBER TS200FR ENGINE AND TINES... - Page 15 REPAIR PARTS 8 HP TILLER ATTACHMENT - - MODEL NUMBER TS200FR ENGINE AND TINES PART DESCRIPTION 124533X Control Throttle 6924J Bracket, Throttle Control 677A860 Hitch Yoke Assembly 4379H Grip, Handle 677A855 Hitch Channel Assembly 6922R Plate, Adapter - - - - - - - Engine 8 H.P., Tecumseh...
- Page 16 REPAIR PARTS 8 HP TILLER ATTACHMENT - - MODEL NUMBER TS200FR TRANSMISSION AND GAUGE WHEELS...
- Page 17 REPAIR PARTS 8 HP TILLER ATTACHMENT - - MODEL NUMBER TS200FR TRANSMISSION AND GAUGE WHEELS PART DESCRIPTION 634A562 Transmission 9135R Retainer Spring 4929H Drilled Pan Head Rivet 3/8 x 1-3/4 634A61 Gauge Wheel Sleeve and Brackets 634A559 Gauge Wheel Adjusting Shaft and...
- Page 18 2480...