Table of Contents
Advertisement
ELECTRIC CHAIN SA W
OWNER'S MANUAL
LNT-2: 076728J, 100089-06, & 099178H
EL-1, EL-1 Fast Sharp
EL-7: 075762J, 098031J, 099039J, 100015,
100089-01, 100089-04, 100089-05, & 100089-07
EL-7 Fast Sharp: 076702J
Pole Saw: 104316-01
Pole Saw Assembly: 104317
IMPORTANT: Read and understand this manual before assembling or
operating this chain saw. Improper use of saw can cause severe
injury. Keep this manual for future reference.
MODELS
®
®
Advertisement
Table of Contents
Related Manuals for Remington 076728J
Summary of Contents for Remington 076728J
- Page 1 ELECTRIC CHAIN SA W OWNER’S MANUAL LNT-2: 076728J, 100089-06, & 099178H EL-1, EL-1 Fast Sharp EL-7: 075762J, 098031J, 099039J, 100015, 100089-01, 100089-04, 100089-05, & 100089-07 EL-7 Fast Sharp: 076702J Pole Saw: 104316-01 Pole Saw Assembly: 104317 IMPORTANT: Read and understand this manual before assembling or operating this chain saw.
-
Page 2: Safety Warnings
ELECTRIC CHAIN SAW SAFETY WARNINGS Make certain you read and un- derstand all Safety Warnings on pages 2 and 3. Improper use of this chain saw can cause severe injury or death from fire, electri- cal shock, body contact with moving chain, or falling wood. -
Page 3: Maintenance And Storage Of Chain Saw
SAFETY WARNINGS KICKBACK WARNING: Kickback may oc- cur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning fast reverse re- action, kicking the guide bar up and back towards the operator. -
Page 4: Electric Chain Saw
ELECTRIC CHAIN SAW CHAIN SAW NAMES AND TERMS Bucking Process of cutting a felled tree or log into lengths. Felling Process of cutting down a tree. Felling Cut Final cut when felling a tree. Make this cut on opposite side of tree from notching cut. -
Page 5: Product Identification
PRODUCT IDENTIFICATION Rear Handle Rear Hand Guard Power Cord Front Handle Motor Housing Figure 2 - Electric Chain Saw 097017 OWNER’S MANUAL Front Hand Guard Guide Bar Nose Chain Guide Bar Spike Scabbard Oil Level Sight Hole (located on saw body, hidden by front handle) Oil Cap Switch... -
Page 6: Assembly
ELECTRIC CHAIN SAW ASSEMBLY Note: Some models are pre assembled. As- sembly is not needed on these models. See Saw Chain Tension Adjustment, page 7. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. IMPORTANT: Do not clamp chain saw in vise during assembly. -
Page 7: Saw Chain Tension Adjustment
ASSEMBLY Continued INSTALLING AUTOMATIC CHAIN SHARPENER (Fast Sharp Models Only) 1. Screw automatic chain sharpener into threaded hole. 2. Continue turning automatic chain sharpener until you hear five (5) clicks. Automatic Chain Sharpener Figure 5 - Automatic Chain Sharpener (Fast Sharp Models Only) 097017 OWNER’S MANUAL SAW CHAIN... -
Page 8: Operating Chain Saw
ELECTRIC CHAIN SAW OPERATING CHAIN WARNING: Read and under- stand this owner’s manual before operating this saw. Make certain you read and understand all Safety Warnings , pages 2 and 3. Improper use of this chain saw can cause severe injury or death from fire, electrical shock, or body contact with moving chain, or falling wood. -
Page 9: Felling A Tree
OPERATING CHAIN Continued FELLING A TREE (Cutting Down a Tree) WARNING: • Avoid kickback. Kickback can result in severe injury or death. See Kickback , page 3 to avoid risk of kickback. • Do not fell a tree without ample skill or expert help. -
Page 10: Bucking A Log
ELECTRIC CHAIN SAW OPERATING CHAIN Continued LIMBING A TREE WARNING: Avoid kickback. Kickback can result in severe in- jury or death. See Kickback, page 3 to avoid risk of kickback. WARNING: When cutting limb that is under tension, use extreme caution. - Page 11 OPERATING CHAIN Continued Log Supported On Both Ends 1. Make first cut from above log (see Fig- ure 16). Cut 1/3 through diameter of log. This cut will keep section from splintering when cut. 2. Make second cut on underside of log, directly under first cut.
-
Page 12: Cleaning And Maintenance
ELECTRIC CHAIN SAW CLEANING AND MAINTENANCE NOTICE: Below are instructions for servicing your chain saw. Any servicing not mentioned below should be done by an authorized service center. CLEANING SAW BODY WARNING: Unplug chain saw from power source before servic- ing. -
Page 13: Sharpening Saw Chain
CLEANING AND MAINTENANCE Continued SHARPENING SAW CHAIN (Non-Fast Sharp Model) WARNING: Unplug chain saw from power source before servic- ing. Severe injury or death could occur from electrical shock or body contact with moving chain. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. -
Page 14: Replacing Saw Chain
ELECTRIC CHAIN SAW CLEANING AND MAINTENANCE Continued Filing Cutter Depth Gauges The cutter depth gauge clearance is reduced as cutters are sharpened. After every second or third sharpening, reset cutter depth gauges. 1. Place depth gauge tool (.025") firmly across top of two cutters. Make sure depth gauge enters slot in depth gauge tool (see Figure 22). -
Page 15: Troubleshooting
TROUBLESHOOTING OBSERVED FAULT Saw runs, but does not cut. Saw does not cut unless heavily forced. Cutting produces only sawdust with few large chips. Saw runs slow. Saw stalls easily. Motor of saw does not run when you squeeze trigger. Motor of saw runs, but chain does not move. -
Page 16: Parts Centrals
ELECTRIC CHAIN SAW Ray's Portable Heater Service Portable Heater Parts 3191 Myers Road 342 North County Road 400 East Camino, CA 95709 Valparaiso, IN 46383 219-462-7441 916-644-7716 1-800-362-6951 Baltimore Electronics 1348 Dixwell Avenue 1349 Adams Street Hamden, CT 06514 Bowling Green, KY 42103-3414 203-248-7553 1-800-397-7553 502-846-1199... - Page 17 INDIANA (IN) KANSAS (KS) Hutchens Sales and Service Abilene Rent-All & Sales R.R. #5, Box 550 1701 West 1st Street Bloomfield, IN 47424 Abilene, KS 67410 812-876-1891 913-263-7668 Nichols Ice & Oil NAAB Electric, Inc. 2018 Park Road 2013 W. Jones Connersville, IN 47331 Garden City, KS 67846 317-825-3741...
- Page 18 ELECTRIC CHAIN SAW NEW JERSEY (NJ) Advanced Power Equipment Complete Saw Service 101 Fairgrounds Drive 336 River Road Manlius, NY 13104 Garfield, NJ 07026 315-682-4010 201-478-7838 P & C Nemeth's Mower Service 12 East Street 55 - 4th Ave. Nunda, NY 14517 Haskell, NJ 07420 716-468-5050 201-835-0080...
-
Page 19: Replacement Parts And Accessories
UTAH (UT) VIRGINIA (VA) Roosevelt Service Center Industrial Hardware 133 South 300 East, Box 1546 4109 Bainbridge Blvd. Roosevelt, UT 84066 Chesapeake, VA 23324 801-722-2708 804-543-2232 Longs Engine Service Warren E. Smith Shops 7536 Stone Road 564 Reading Rd. Ext. Salt Lake, UT 84121 300 Madestic Drive 801-943-5135... -
Page 20: Repair Service
REPAIR SERVICE Note: Only use original replacement parts. This will protect your warranty coverage for parts replaced under warranty. Each authorized service center is indepen- dently owned and operated. For additional service center or warranty information, call 1-800-323-5190. ELECTRIC CHAIN SAW LIMITED WARRANTY Always specify model and serial numbers when writing the factory.