Summary of Contents for Century Clone Plus CROS2EU2CP
- Page 1 Century Corporation User's Manual HDD Stand Converter Clone Plus CROS2EU2CP User Manual CROS2EU2CP Manual 2010/04/27...
-
Page 2: Package Contents
【Features】 Part no. : CROS2EU2CP Model name : HDD Stand Converter Clone Plus Interface : Device...SATA I/II 1.5Gbps/3.0Gbps Host ...[USB]USB2.0 [eSATA]SATA II 3.0Gbps Connector : USB TYPE-B Dimension : L143mm x W132mm x H70mm Weight : 544g (HDD not included) Humidity : 20% to 80% Temperature: 5~35°C Power Adapter:Input...100V~240V 0.8A Output...12V 3A... -
Page 3: Hardware Guide
【Hardware Guide】 〈Front〉 HDD dock slot HDD release button Operation panel 〈Back〉 ① eSATA port ② USB 2.0 port ③ Power adapter port... -
Page 4: Operation Panel
〈Operation Panel〉 ① Power Switch: When power on,will show blue light. ② PC / Copy Mode Switch: PC Mode (Blue light):When CROS2EU2CP connects with PC. - Copy Mode(Red light):When power is on,long press the button for 3 seconds. After the LED turn to RED, can begin copy operation. ③... -
Page 5: Installation
【HDD/SSD Installation】 Before insert the HDD ■ Please be careful with the static electricity, when insert the HDD. The static electricity might cause the damage to the HDD stand converter. ※ Warning! Please back up the data of the HDD before connecting. Warning! ■Please be careful withe the order. - Page 6 ※CROS2EU2CP is for SATA HDD, does not support PATA(IDE) HDD. confirm Warning! SATA Connector PATA Connector ■3.5＂HDD installation Insert the 3.5＂hard drive into the dock slot 〈After〉 ■2.5＂HDD installation Insert the 2.5＂hard drive into the dock slot 〈After〉 ■ Warning！ When install, please notice the correct SATA connector location and direction.
- Page 7 【HDD/SSD Remove】 ※ CROS2EU2CP does not support hot-swap plug. Please turn off the power before remove. 1.One hand hold on the HDD, and push the button to release the HDD from the dock. Hold on the HDD! Push the release button 2.After pushing, the HDD will eject from the docking.
-
Page 8: Connect With Pc
【Connect with PC】 Connect the PC and power to start! CROS2EU2CP docking USB port eSATA port eSATA cable Cannot work at the same time 同時に使用す できま AC adapter Power cord USB2.0 Cable Plug （100V AC ） ※ Above is an example. Please do not twist the eSATA cable when using. -
Page 9: Turn On The Power
【Turn on the Power】 Press the button to trun on and turn off the power. Please turn off the power before connect with cable. Power ON BLUE LED Power OFF LED OFF... - Page 10 【HDD Copy Function】 HDD docking station deliver an exact 1 to 1 , sector by sector disk copy. No need to format the HDD,if there are system files already in the HDD. Warning! ～Before Copy Operation～ Please read the operation manual before start copy operation, there might cause damage to the HDD, if the operation is wrong.
- Page 11 2.After confirm the power is off, insert the Source Disk into HDD 2, and insert Target Dick into HDD 1. HDD 2 POWER OFF (SOURCE DISK) CONFIRMED! HDD 1 (TARGET DISK) COPY Please be careful with the correct solt for the TARGET and SOURCE DISK. It might cause damage to the HDD, if it’s reversed.
- Page 12 3.Press the button to start!(①) Press PC/COPY button for 3 seconds, LED will turn from blue to red（②） POWER ON Long press for 3 seconds Blue Turn to red 4.Press START button to start copy operation. When in copy operation,HDD1/HDD2 light will be pink flash, and the Progress Status LED will be blue flash from left to right,25% a unit to indicate the finished copy status.
- Page 13 【Copy Operation-Technical Support】 Following are the reasons might cause the duplication process could not begin or disrupt, ■ Could not begin process One of the HDDs might have broken, or the TARGET HDD is smaller than SOURCE HDD in capacity. Please change a HDD or bigger TARGET HDD. HDD1/HDD2 LED only flashes once pink flash Progress LED is not flshing ■...
- Page 14 【FAQ】 Q:Maximum capacity of HDD? A:Support HDD up to 2.0 TB in capacity. Q:Does it support hot-swap? A:No, please turn off the power before insert or remove the HDD. It may cause damage to the HDD, if the power is on. Q:What is the insertion rate of the HDD converter? A:For the HDD stand converter, 10,000 times.
- Page 15 【FAQ- Copy Mode】 Q:Could it copy HDD in different capacity? A:Yes, but the TARGET HDD should always bigger than SOURCE HDD. Q:Could it use the remain capacity in the HDD after copy operation? A:In the copy mode it will copy all sector in the HDD. For example, the SOURCE HDD is 500GB and the TARGET HDD is 1TB,the 500GB in the TARGET HDD will be exactly the same as the SOURCE HDD.