Table of Contents
Advertisement
Carburetor
Your Husqvarna product has been designed and
manufactured to specifications that reduce harmful
emissions. After the engine has used 8-10 tanks of fuel
the engine will be run-in. To ensure that it continues to run
at peak performance and to minimise harmful exhaust
emissions after the running-in period, ask your dealer/
service workshop (who will have a rev counter at their
disposal) to adjust your carburettor.
Function, Basic settings, Fine adjustment
WARNING! Do not start the chain saw
!
unless the bar, chain and clutch cover
(chain brake) are fitted, otherwise the
clutch may come loose and cause
personal injury.
Function
•
The carburetor governs the engine's speed via the
throttle control. Air and fuel are mixed in the
carburetor. The air/fuel mixture is adjustable. Correct
adjustment is essential to get the best performance
from the machine.
•
The setting of the carburetor means that the engine is
adapted to local conditions, for example, the climate,
altitude, fuel and the type of 2-stroke oil.
•
The carburettor has two adjustment controls:
- L = Low speed jet
- T = Idle adjustment screw (Maximum speed is
controlled by a fixed jet/electronic speed governor).
•
The amount of fuel that is mixed with the air admitted
by the throttle opening is adjusted using the low speed
jet. If this is turned clockwise it gives a leaner air/fuel
mixture (less fuel) and if it is turned anti-clockwise it
gives a richer air/fuel mixture (more fuel). A leaner
mixture gives a higher engine speed, while a richer
mixture gives a lower engine speed.
•
The T-screw regulates the throttle setting at idle
speed. If the T-screw is turned clockwise this gives a
higher idle speed; turning it anti-clockwise gives a
lower idle speed.
Basic settings and running in
The basic carburetor settings are adjusted during testing
at the factory.
The carburetor is set to its basic setting when test run at
the factory. The basic setting is richer than the optimum
30 – English
MAINTENANCE
setting and should be maintained for the first hours that
the machine is in use. The carburetor should then be
finely adjusted. Fine adjustment should be carried out by
a suitably trained person.
CAUTION! If the chain rotates while idling the T-screw
must be turned anti-clockwise until the chain stops.
Rec. idle speed: 2500 rpm
Fine adjustment
When the saw has been "run-in" the carburettor should be
finely adjusted. The fine adjustment should be carried out
by qualified person. The L-needle is adjusted first, then
the idling screw T. 2500 rpm
Conditions
•
Before any adjustments are made the air filter should
be clean and the cylinder cover fitted. Adjusting the
carburetor while a dirty air filter is in use will result in
a leaner mixture next time the filter is cleaned. This
can give rise to serious engine damage.
•
Turn the low speed jet carefully clockwise until it
bottoms. Now turn it one turn anti-clockwise. The
carburettor is now set to L = 1.
•
Now start the machine according to the starting
instructions and let it warm up for 10 minutes.
CAUTION! If the chain rotates while idling the T-
screw must be turned anti-clockwise until the
chain stops.
•
Place the machine on a flat surface so that the bar
points away from you and so that the bar and chain do
not come into contact with the surface or other
objects.
Low speed jet L
Turn the low speed jet L clockwise until it stops. If the
engine accelerates poorly or idles unevenly, turn the low
speed jet L anticlockwise until good acceleration and
idling are achieved.
CAUTION! If the chain rotates while idling the T-screw
must be turned anti-clockwise until the chain stops.
Final setting of the idling speed T
Adjust the idle speed with the T-screw. If it is necessary to
re-adjust, turn the T-screw clockwise while the engine is
running, until the chain starts to rotate. Then turn counter-
clockwise until the chain stops. A correctly adjusted idle
speed setting occurs when the engine runs smoothly in
every position. It should also be good margin to the rpm
when the chain starts to rotate.
!
WARNING! Contact your servicing
dealer, if the idle speed setting cannot be
adjusted so that the chain stops at idle.
Do not use the chain saw until it has
been properly adjusted or repaired.
Advertisement
Table of Contents
