Related Manuals for Husqvarna 1151338-95
Summary of Contents for Husqvarna 1151338-95
- Page 1 Oper ator’s manual (EPA I) 395XP Please r ead the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. - Page 3 KEY T O SYMBOLS EP A I The Emissions Compliance P eriod referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements. Category C = 50 hours, B = 125 hours, and A = 300 hours.
-
Page 4: Table Of Contents
Contents KEY TO SYMBOLS Symbols on the machine: ... 2 Symbols in the operator’s manual: ... 2 CONTENTS Contents ... 4 INTR ODUCTION Dear customer! ... 5 WHA T IS WHAT? What is what on the chain sa w? ... 6 GENERAL SAFETY PRECA UTIONS Bef ore using a new chain saw ... -
Page 5: Intr Oduction
Dear customer! Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. -
Page 6: Wha T Is What
11 Fuel tank 12 Muffler 13 Bar tip sprocket 14 Chain 15 Bar 6 – English WHA T IS WHA T? Husqvarna XXXX XXXX XXXXXXX Husqvarna AB Huskvarna, SWEDEN 16 Bumper spike 17 Chain catcher (Catches chain if it jumps or breaks.) -
Page 7: General Safety Preca Utions
GENERAL SAFETY PRECA UTIONS Bef ore using a new chain saw • Please read this manual carefully. • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly. • Refuel and start the chain saw. See the instructions under the headings Fuel Handling and Starting and Stopping. -
Page 8: Always Use Common Sense
GENERAL SAFETY PRECA UTIONS Al ways use common sense It is not possib le to cover every conceivable situation you can face when using a chain saw. Always exercise care and use your common sense. Avoid all situations which you consider to be beyond your capability. - Page 9 GENERAL SAFETY PRECAUTIONS • The chain brake (A) can either be activated manually (by your left hand) or automatically by the inertia release mechanism. • The brake is applied when the front hand guard (B) is pushed forwards. • This movement activates a spring-loaded mechanism that tightens the brake band (C) around the engine drive system (D) (clutch drum).
-
Page 10: Chain Catcher
GENERAL SAFETY PRECAUTIONS of the front hand guard, the chain brake can only be activated by the inertia action. Will my hand always activate the chain brake during a kickback? No. It takes a certain force to move the hand guard forward. -
Page 11: Cutting Equipment
GENERAL SAFETY PRECAUTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. The machine′s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine′s handle unit. The body of the chain saw, including the cutting equipment, is insulated from the handles by vibration damping units. - Page 12 To maintain the safety features of the cutting equipment, you should replace a worn or damaged bar or chain with a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical Data for a list of replacement bar and chain combinations we recommend.
-
Page 13: Sharpening Your Chain And Adjusting Depth Gauge Setting
GENERAL SAFETY PRECAUTIONS Chain • Chain pitch (inches) • Drive link width (mm/inches) • Number of drive links. Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teeth • Never use a blunt chain. When the chain is blunt you have to exert more pressure to force the bar through the wood and the chips will be very small. -
Page 14: Tensioning The Chain
GENERAL SAFETY PRECAUTIONS • File all the teeth to the same length. When the length of the cutting teeth is reduced to 0.16 inch (4 mm) the chain is worn out and should be replaced. General advice on adjusting depth gauge setting •... -
Page 15: Lubricating Cutting Equipment
GENERAL SAFETY PRECAUTIONS Lubricating cutting equipment WARNING! Poor lubrication of cutting equipment may cause the chain to snap, which could lead to serious, even fatal injuries. Chain oil Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather. - Page 16 GENERAL SAFETY PRECAUTIONS Chain drive sprocket The clutch drum is fitted with one of the following drive sprockets: A Spur sprocket (the chain sprocket is welded on the drum) B Rim sprocket (replaceable) Regularly check the degree of wear on the drive sprocket. Replace if wear is excessive.
-
Page 17: Assembly
Fitting the bar and chain WARNING! Always wear gloves, when working with the chain. Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle. Remove the bar nuts and remove the clutch cover (chain brake). -
Page 18: Fuel Handling
When working with continuous high revs (e.g. limbing) a higher octane is recommended. Environment fuel HUSQVARNA recommends the use of alkylate fuel or environmental fuel for four-stroke engines blended with two-stroke oil as set out below. Note that carburetor adjustment may be necessary when changing the type of fuel (see instructions under the heading Carburetor). -
Page 19: Fueling
Fueling WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke and do not place any hot objects in the vicinity of fuel. Always stop the engine and let it cool for a few minutes before refuelling. When refuelling, open the fuel cap slowly so that any excess pressure is released gently. -
Page 20: Starting And Stopping
Starting and stopping WARNING! Note the following before starting: Never start a chain saw unless the bar, chain and all covers are fitted correctly. Otherwise the clutch can come loose and cause personal injuries. Place the machine on firm ground. Make sure you have a secure footing and that the chain cannot touch anything. -
Page 21: Starting And Stopping
• Never start a chain saw unless the bar, chain and all covers are fitted correctly. See instructions under the heading Assembly. Without a bar and chain attached to the chain saw the clutch can come loose and cause serious injury. •... -
Page 22: Working Techniques
Before use: Check that the chain brake works correctly and is not damaged. Check that the rear right hand guard is not damaged. Check that the throttle lockout works correctly and is not damaged. Check that the stop switch works correctly and is not damaged. -
Page 23: General Rules
Before moving your chain saw switch off the engine and lock the chain using the chain brake. Carry the chain saw with the bar and chain pointing backwards. Fit a guard to the bar before transporting the chain saw or carrying it for any distance. When you put the chain saw on the ground, lock the saw chain using the chain brake and ensure you have a constant view of the machine. -
Page 24: Basic Cutting Technique
user. If the saw chain is jamming, the saw may be pushed back at you. Unless the user resists this pushing force there is a risk that the chain saw will move so far backwards that only the kickback zone of the bar is in contact with the tree, which can lead to a kickback. -
Page 25: Tree Felling Technique
Limbing When limbing thick branches you should use the same approach as for cutting. Cut difficult branches piece by piece. Cutting WARNING! Never attempt to cut logs while they are in a pile or when a couple of logs are lying together. Such procedures drastically increase the risk of kickback which can result in a serious or fatal injury. - Page 26 Felling direction The aim is to fell the tree in a position where you can limb and cross-cut the log as easily as possible. You want it to fall in a location where you can stand and move about safely. Once you have decided which way you want the tree to fall you must judge which way the tree would fall naturally.
- Page 27 Next make the bottom cut so that it finishes exactly at the end of the top cut. The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45°. The line where the two cuts meet is called the directional cut line.
-
Page 28: How To Avoid Kickback
Freeing a tree that has fallen badly Freeing a ”trapped tree” It is very dangerous to remove a trapped tree and there is high accident risk. Never try to fell the tree that is trapped. Never work in the risk zone of the hanging trapped tree. The safest method is to use a winch. - Page 29 was being used when the kickback zone of the bar touched the object. Kickback only occurs if the kickback zone of the bar touches an object. Limbing WARNING! A majority of kickback accidents occur during limbing. Do not use the kickback zone of the guide bar. Be extremely cautious and avoid contacting the log, other limbs or objects with the nose of the guide bar.
-
Page 30: Maintenance
These limit the adjustment possibilities to a maximum of a 1/2 turn. Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. Function, Basic settings, Fine adjustment... -
Page 31: Checking, Maintaining And Servicing Chain Saw Safety Equipment
Fine adjustment of the idling speed T Adjust the idle speed with the T-screw. If it is necessary to re-adjust, turn the T-screw clockwise while the engine is running, until the chain starts to rotate. Then turn counter- clockwise until the chain stops. A correctly adjusted idle speed setting occurs when the engine runs smoothly in every position. -
Page 32: Throttle Lockout
Checking the inertia brake release With the engine turned off, hold the chain saw over a stump or other firm object. Let go of the front handle so that the bar drops towards the stump as the chain saw rotates around the rear handle. When the bar hits the stump the brake should be applied. -
Page 33: Muffler
Chain catcher Check that the chain catcher is not damaged and is firmly attached to the body of the chain saw. Right hand guard Check that the right hand guard is not damaged and that there are no visible defects, such as cracks. Vibration damping system Regularly check the vibration damping units for cracks or deformation. -
Page 34: Starter
Starter WARNING! When the recoil spring is wound up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury. Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective gloves. -
Page 35: Air Filter
A damaged air filter must always be replaced. A HUSQVARNA chain saw can be equipped with different types of air filters according to working conditions, weather, season, etc. Contact your dealer for advice. -
Page 36: Needle Bearing Lubrication
1 1/2 turns from the closed position. Bar 28" and longer: 1 3/4 turns from the closed position. These recommendations apply to Husqvarna’s chain oil, for other chain oils increase the oil flow by one step. WARNING! The engine must be stopped when making adjustments. -
Page 37: Winter Use
Winter use Running problems can occur when using the machine in the cold and snowy conditions caused by: • Too low engine temperature. • Icing of the air filter and carburetor. Special measures are therefore often required: • Partly mask the air inlet on the starter to increase the working temperature of the engine. -
Page 38: Maintenance Schedule
Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily maintenance Clean the outside of the machine. Check that the components of the throttle control work safely. -
Page 39: Technical Data
Technical data Engine Cylinder displacement, cu.in/cm Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Power, kW/ rpm Ignition system Manufacturer of ignition system Type of ignition system Spark plug Electrode gap, inch/mm Fuel and lubrication system Manufacturer of carburetor Carburetor type Fuel tank capacity, US pint/litre Oil pump capacity at 8,500 rpm, ml/min Oil tank capacity, US pint/litre... -
Page 40: Saw Chain Filing And File Gauges
Recommended original and replacement bar and chain combinations The Husqvarna 395XP is in the ANSI category of saws above 3,8 cu. in. and is not required to comply with low kickback performance requirements. However, for this model we recommend the following cutting equipment. -
Page 41: Federal Emission Control Warranty Statement Your Warranty Rights And Obligations
You are responsible for presenting your small nonroad engine to a Husqvarna Forest & Garden authorized servicing dealer as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. -
Page 42: American Standard Safety Precautions
AMERICAN STANDARD SAFETY PRECAUTIONS Safety precautions for chain saw users (ANSI B175.1-2000 Annex C) Kickback safety precautions WARNING! Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. - Page 44 1151338-95 ´®z+SAy¶5<¨ ´®z+SAy¶5<¨ 2009-08-24...