Related Manuals for Dolmar PS-410
Summary of Contents for Dolmar PS-410
-
Page 1: Instruction Manual
Instruction Manual Important: Read this instruction manual carefully before putting the chain saw into operation and strictly observe the safety regulations! Keep this instruction manual! PS-410 PS-411 http://www.dolmar.com... -
Page 2: Table Of Contents
EU guidelines were: EN 5008‑, Packing EN 5008‑, EN 550, EN 608, CISPR . The DOLMAR chain saw will be delivered in a protective card‑ The conformity assessment procedure 000/4/EG was perfor‑ board box to prevent transport damage. -
Page 3: Delivery Inventory
Delivery inventory 1. Chain saw 2. Guide bar 3. Saw chain 4. Chain protection cover 5. Assembly tool In case one of the parts listed should not be included in the 6. Instruction manual (not shown) delivery inventory, please consult your sales agent. Symbols You will notice the following symbols on the chain saw and in the instruction manual: Read instruction manual Caution, kickback! and follow the warning-... -
Page 4: Safety Precautions
SAFETY PRECAUTIONS Intended use Power chain saws This power chain saw may be used only for sawing wood out of doors. During operation of the chain saw safety shoes or safety ‑ It is intended for the followung uses depending on its class: boots (7) fitted with anti skid sole, steel toe caps and pro‑... -
Page 5: Fuels / Refuelling
Fuels / Refuelling ‑ Stop the engine before refuelling the chain saw. ‑ Do not smoke or work near open fires (5). ‑ Let the engine cool down before refuelling. ‑ Fuels can contain substances similar to solvents. Eyes and skin should not come in contact with mineral oil products. -
Page 6: Kickback
Kickback ‑ When working with the chain saw dangerous kickbacks may occur. ‑ Kickback occurs when the upper part of the end of the guide bar inadvertently touches wood or other hard objects (0). ‑ This causes the saw to be thrown back toward the user with great force and out of control. - Page 7 ‑ Be careful when cutting splintery wood. Cut pieces of wood may be pulled along (risk of injuries). ‑ When cutting with the upper edge of the guide bar, the chain saw may be pushed in the direction of the user if the chain gets clamped.
-
Page 8: Transport And Storage
DOLMAR Service. Use only original DOLMAR spare parts and accessories. Using spare parts other than original DOLMAR parts or acce‑ sories and guide bar/chain combinations or lengths which are not approved bring a high risk of accidents. We cannot accept any responsibility for accidents and damage resulting from using sawing devices or accesories which have not been approved. -
Page 9: Technical Data
Chain oil tank capacity 0. 0. Mixture ratio (fuel/two‑stroke oil) ‑ when using DOLMAR oil 50: 50: ‑ when using DOLMAR HP 00‑oil 00: 00: ‑ when using other oils 40: 40: Chain brake engages manually or in case of kickback Chain speed 7.5... -
Page 10: Putting Into Operation
PUTTING INTO OPERATION Mounting the guide bar and saw chain CAUTION: Before doing any work on the guide bar or Use the universal wrench delivered with the chain saw for the chain, always switch off the engine and pull the following work. -
Page 11: Tightening The Saw Chain
NOTE: ‑ Turn the chain tightener (C/6) to the right (clockwise) until the chain engages the guide groove of the bottom If the chain brake on the dismounted sprocket guard is actuated side of the bar (see circle). Press the guide bar against the by accident, it must be released again prior to reassembly: housing with your left hand. - Page 12 For lubricating the engine use a two‑stroke engine oil (quality grade: JASO FC or ISO EGD), which is added to the fuel. The engine has been designed for use of DOLMAR HP 00 high‑ performance two‑stroke engine oil and a mixture ratio of only 00: to protect the environment.
-
Page 13: Adjusting The Chain Lubrication
The use of bio‑degradable oil may even be required by local regulations. The chain oil BIOTOP sold by DOLMAR is made of special vegetable oils and is 00% bio‑degradable. BIOTOP has been granted the "blue angel" (Blauer Umweltschutz‑Engel) for being particularly environment‑friendly (RAL UZ 48). -
Page 14: Warm Start
The high pressure increase in the combustion chamber that results from the first ignitions will automatically close the starting valve (button pops back out). Models PS-410 do not have a starting valve. Starting and carburetor adjustment are as for model PS-411 except without the instruction "Push the starting valve". CAUTION: As soon as the engine is started it must be put in idle to prevent the chain brake from being damaged. -
Page 15: Checking The Chain Lubrication
Turn in the idle adjusting screw (Speed) (clockwise): Idle speed goes up. Caution: If after this adjustment the cutting tool still rotates during idle, do NOT work with the unit! Take it to a DOLMAR service centre! SERVICE Note: Carburetor adjustment is necessary for optimum engine performance, for safer and more economical ope- ration. -
Page 16: Working In Winter
Working in winter normal operation subfreezing operation In order to prevent carburetor icing in conditions of low tem‑ ‑ Remove the filter cover (B/1). perature combined with high humidity, and in order to get up ‑ Position the universal wrench (B/2) as shown above and to operating temperature faster in subfreezing temperatures, push the insert (B/3) out by tapping the wrench. -
Page 17: Cleaning The Guide Bar, Lubricating The Sprocket Nose
‑ All cutters must be sharpened to the same angle, 30°. Dif‑ Files and how to work with them ferent angles result in a roughly, irregularly running chain, ‑ Sharpen using a special file holder with a saw chain round file. increase wear and tear and cause chain beakage. -
Page 18: Cleaning The Brake Band And Sprocket Interior
Regular inspection and maintenance are important for ‑ Remove the chain (A/3) and guide bar (A/4). your own safety and must be done by a DOLMAR service centre. ‑ Clean the interior with a brush, in particular the brake‑band area (A/5). -
Page 19: Cleaning The Air Filter
Cleaning the air filter ‑ Remove the filter cover (E/1) ( screws). ‑ Clean the air filter with a soft brush. ‑ If the filter is very dirty, clean it in lukewarm water with dish‑ CAUTION: washing detergent. Pull the choke (E/2) to shut the choke valve and to prevent dirt Let the air filter dry completely. -
Page 20: Instructions For Periodic Maintenance
We therefore recommend that you consult a DOLMAR service centre for all work not described in this instruction manual. The DOLMAR service centres have all the necessary equipment and skilled and experienced personnel, who can work out cost‑... -
Page 21: Spare Parts
Please bear in mind that if parts other than original DOLMAR spare parts are used, this will automatically invalidate the DOLMAR product guarantee. -
Page 22: Extract From The Spare Parts List
Extract from the spare parts list PS-410 Use only original DOLMAR parts. For repairs and replacement of other parts, see PS-411 your DOLMAR service centre. Pos. DOLMAR-No. Qty. Denomination 44 033 4 Sprocket nose bar .35”, .050”, 33 cm 44 038 4 Sprocket nose bar .35”, .050”, 38 cm... - Page 23 Important information for order replacement saw chains and guide bars! If using a guide bar with a .3 mm (.050”) groove width, only use the matching saw chain with a .3 mm (.050”) drive elemant strenght. .3 mm (.050”) groove width guide bars are marked with this symbol Notes...
- Page 24 DOLMAR GmbH Specifications subject to change without notice Postfach 70 04 0 D‑004 Hamburg Germany Form: 995 70 65 (5.06 GB) http://www.dolmar.com...