Advertisement
Quick Links
Advertisement
Summary of Contents for Symbol CyberPen
- Page 1 Welcome to CyberPen CyberPen User Guide...
- Page 2 This warranty is limited to repair or replacement at Symbol’s option, with rea- sonable promptness after being returned to Symbol by a carrier selected and paid for by the cus- tomer. These provisions do not prolong the original warranty term for any Symbol product which has been repaired or replaced by Symbol.This warranty applies to the original owner and does...
- Page 3 Getting Started with the CyberPen Before you can start using your CyberPen, you must first perform some basic set up procedures. Unpacking the CyberPen Your CyberPen package should contain the following items: •...
- Page 4 Shack Fulfillment Center at: 1-800-THE-SHAC (1-800-843- 7422). Inserting Batteries into the CyberPen Before using the CyberPen, you must first insert the three sil- ver oxide batteries into the pen: Holding the clip end of the pen, twist the pen end of the...
- Page 5 Insert the batteries one at a time with the positive (+) end up into the clip end of the pen: Twist the bottom of the pen back on clockwise:...
-
Page 6: Adjusting The Beeper Volume
Tighten the connector’s screws to ensure proper con- nection. Adjusting the Beeper Volume The CyberPen’s beeper has four volume levels: High, Medium, Low, and Off. To change the beeper volume, press the scan button twice quickly. Upon pressing the scan button twice, you should hear a sample of the newly selected vol- ume. - Page 7 Scanning with the CyberPen Now that your set up is complete, you’re ready to scan bar codes. Hold the pen at an angle as shown in the diagram below with the clear tip facing the bar code to be scanned.
- Page 8 Inserting the CyberPen in the Cyberwell In order for the CyberPen to upload the collected bar code data to the PC, the pen must be properly inserted in the Cyberwell as illustrated: Uploading Bar Code Data To upload the collected bar code data to the PC: Ensure the PC program is ready to receive data.
- Page 9 Writing with the CyberPen To use the writing instrument, hold the tip (writing end) of the pen and twist the body, until the full pen tip is exposed. Pen Refill Removal and Insertion The pen refill cartridge comes equipped with a removal tool.
- Page 10 Pen Refill To insert a new ink cartridge, insert the ink end of the pen into the pen as shown: groove...
-
Page 11: Set Defaults
Parameter Bar Codes The following bar code parameter menus can be used to pro- gram the scanner. Clear Bar Codes The following bar code clears the bar code data collected and currently stored in the pen. Clear Bar Codes Set Defaults This parameter resets the pen to the default values for all parameters. - Page 12 Good Decode LED On Time This is the duration the Green LED remains on following a good decode. .25sec .5 sec .75 sec. (default) 1.0 sec...
- Page 13 Volume This parameter is used to change the beeper volume on the pen. Alternatively, beeper volume can be changed by double- clicking the scan button on the pen. Quiet/Off Low Volume Medium Volume High Volume (default)
- Page 14 Continuous Scan Enable/Disable When enabled, this parameter allows you to scan multiple bar codes with one press and hold of the scan button. When disabled, the scan button must be pressed each time to ini- tiate a scan. Continuous Scan Enabled (default) Continuous Scan Disabled...
- Page 15 Connect the equipment into an outlet on a circuit different from that which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help Caution: Changes or modifications not expressly approved by Symbol Technologies Inc, could void your authority to operate this equipment. Radio Frequency Interference Requirements - Canada This Class B digital apparatus meets the requirements of the Canadian Interference-Causing Equipment Regulations.
- Page 16 Applicable Standards: • EN 55 022 - Limits and Methods of Measurement of Radio Interference Characteristics of Information technology Equipment • EN 50 082-1 - Electromagnetic Compatibility - Generic Immunity Stan- dard, Part 1: Residential, commercial, Light Industry • IEC 801.2 - Electromagnetic Compatibility for Industrial Process Measure- ment and Control Equipment Part 2: Electrostatic Discharge Requirements •...