Set Up; Connect Power; Power On/ Standby Mode; Setting The Clock Time Using The Auto-Sync Clock Feature - Honeywell Ovale OVD270 Instruction Manual

SPECIFICATIONS (CONTINUED)
General Specifications:
• AC Power Adapter:
– Model: HK-AX-120A200-CP
– Input: 100-240V~50/60Hz 0.8A
– Output: 12V 2.0A
• Operating Power Consumption: <32W
• Standby Power Consumption: <1W
• Dimensions: Main Unit (WxHxD)
298 x 114 x 98mm/ 11.73" x 4.49" x 3.86"
• Weight: Main Unit: 1.25Kg/ 2.75Lbs
With Packing: 1.8Kg/ 3.9Lbs

SET UP

Connect Power

AC Power Adapter
(Plug into AC Electrical Outlet)
Lightning Dock
Cover
AC Electrical Outlet
AC Power Adapter
(Plug into DC Jack)
1. Connect the AC Power Adapter Cable into the DC Jack on
the back of the Ovale Wireless Docking Speaker.
™
2. Plug the AC Power Adapter into an available AC Electrical
Outlet.
8
SET UP (CONTINUED)
3. The LED Display Screen will glow to indicate power has
been connected correctly.

Power On/ Standby Mode

1. Press the Button to switch ON the Ovale ™ Wireless
Docking Speaker. The speaker and the LED Display
Screen will automatically switch to the last selected Audio
Source Mode.
2. Press and hold the Button for about 2 seconds to
switch the speaker "OFF" to Standby Mode. In Standby
Mode, the entire unit switches off and only the clock time
will appear on the LED Display Screen.
IMPORTANT: Unplug the AC Power Adapter to completely
switch off the speaker and Clock Display Screen. All Clock
and Alarm Clock settings will be forgotten and must be
reset upon reconnecting the power to the speaker.
Setting the Clock Time
12 Hour Display 24 Hour Display
PM
Indicator
Light
Setting the Clock Time using the Auto-Sync Clock
Feature
SET UP (CONTINUED)
1. Make sure the Docking Speaker is in Standby Mode and
the clock time has not yet been set.
2. Lift the Lightning Dock Cover and gently place the iPod/
iPhone/ iPad onto the Lightning Dock Connector. Insert the
iPad Stand behind the Lightning Dock Connector when
docking an iPad.
IMPORTANT: You must remove any external iPod/ iPhone/
iPad case before docking the device onto the Docking
Speaker.
3. Dock your iPod/ iPhone/ iPad onto the the Docking
Speaker and wait for about 10 seconds.
4. The time on the LED Display Screen will automatically
match the time on your iPod/ iPhone/ iPad.
IMPORTANT: Since the clock synchronizes with the time
on your iPod/ iPhone/ iPad, you should make sure the time
on your device is correct before setting up the time using
the Auto-Sync Clock feature.
IMPORTANT: After you have performed the auto-sync
procedure the first time, the Docking Speaker will not
auto-sync the time with other devices that are docked
LED Display
later. The time can only be changed manually using the
Screen:
Clock Time main unit or Remote Control, or you can unplug and
Not Set
re-plug the power adapter to cancel the previous
auto-synchronized time and repeat the Auto-Sync Clock
set up steps above.
SET UP (CONTINUED)

Setting the Clock Time using the Remote Control

1. Make sure the Docking Speaker is in Standby Mode, or
switch to Standby Mode by pressing and holding the
Button for 2 seconds until the Display Screen shows the
clock time.
2. Press and hold the CLOCK Button on the Remote Control
for about 2 seconds, until you see "24H" or "12H"
blinking on the LED Display Screen.
3.
Press the and Button on the Remote Control to
select a 12 or 24 Hour display format. Press the CLOCK
Button to confirm.
4.
Press the and Button again to select the Hour time
setting. The Hour digits will blink while you select the
correct Hour digit. Press the CLOCK Button to confirm.
5.
When the Hour digit has been set, press the and
Button again to select the Minute setting. The Minute
digits will blink while you select the correct Minute digit.
Press the CLOCK Button to confirm.

Setting the Clock Time on the Docking Speaker

1.
Make sure the Docking Speaker is in Standby Mode, or
switch to Standby Mode by pressing and holding the
Button for 2 seconds until the Display Screen shows the
clock time.
9