Download
Share
Print this page
Culligan Mark 100 Owner's Manual
  1. Manuals
  2. Brands
  3. Culligan Manuals
  4. Water System
  5. Mark 100
  6. Owner's manual

Culligan Mark 100 Owner's Manual

Automatic water conditioner
Hide thumbs Also See for Mark 100:

Advertisement

Quick Links

Cat. No. 01882220
Rev. B 1/22/01
DCO #
Owner's
Guide
CULLIGAN
®
MARK 100
AUTOMATIC
WATER CONDITIONER
©2001 Culligan International Company
Printed in USA

Advertisement

loading

Related Manuals for Culligan Mark 100

Summary of Contents for Culligan Mark 100

  • Page 1 Cat. No. 01882220 Rev. B 1/22/01 DCO # Owner's Guide CULLIGAN ® MARK 100 AUTOMATIC WATER CONDITIONER ©2001 Culligan International Company Printed in USA...

  • Page 2: Thank You

    We promise that you’ll never want to be without it again. Congratulations, too, on selecting one of the “first family” of water conditioners in the prestigious Culligan Mark Series. With Culligan’s many years of knowledge and experience in water treatment, you can be confident that the model you selected has been designed and engineered to provide years of service with a minimum of care and attention.

  • Page 3: Table Of Contents

    Softener Model Performance Data Sheets are included in this manual for the various Mark 100 Softener models. Refer to the Perfor- mance Data Sheet for your specific softener, as there are slight differences between the models. The softener warranty is located on page 16 of this Owner's Guide.

  • Page 4: Specifications

    Specifications Culligan Mark 100 Water Conditioners with Time Clock, Aqua-Sensor Device or Soft-Minder Meter ® ® ® 9” Model 12” Model Control Valve 5-cycle, Reinforced Thermoplastic 5-cycle, Reinforced Thermoplastic Overall Conditioner Height 51 in 51 in 1 295 mm 1 295 mm...
  • Page 5 Softened water is not recommended for house plants because a build-up of sodium in the soil may interfere with efficient absorption of water by the plant root system. Additional information may be obtained from your independently operated Culligan dealer. INTRODUCTION...
  • Page 6 Some localities have corrosive water. A softener cannot correct this problem and so its printed warranty disclaims liability for corrosion of plumbing lines, fixtures or appliances. If you suspect corrosion, your Culligan Man has equipment to control the problem. Iron is a common water problem. The chemical/physical nature of iron found in natural water supplies is exhibited in four general types: 1.
  • Page 7 Since a predetermined amount of salt is dissolved with each brine refill cycle, the salt must be periodically replenished in order to maintain efficient operation. Your Culligan serviceperson will be able to tell you about how often salt must be added to the salt storage container.
  • Page 8 ® Should service become necessary, a phone icon will appear in the display. If this condition occurs, call your local Culligan dealer for assistance. The phone icon will be the only item displayed when service is required on the control.
  • Page 9 If a small padlock icon appears in the lower right corner of the display, the microprocessor settings are locked and only the Time- of-Day setting can be adjusted, call your Culligan Dealer if setting changes are required. With a flashing or blank display, pressing the...
  • Page 10 AUTOMATIC SALT DELIVERY SERVICE Ask your Culligan Dealer for details about salt delivery service. You can have your salt supply replenished on a regular basis. Whether you have automatic delivery service or pick up salt from your Culligan Dealer, you will be getting quality salt packaged according to rigid Culligan specifications.
  • Page 11 To Clean Out the Salt Storage Tank A periodic clean-out of the Salt Storage Tank is necessary to keep your Culligan Water Conditioner at peak operating efficiency. Do it at least every 2 years when the salt supply is low. Follow these step-by-step procedures: Tools needed: •...

  • Page 12: Performance Data Sheet

    Working Pressure Range: 20-125 psi (140-860 kPa) The Culligan Mark 100 water softeners are tested and validated by WQA against ANSI/NSF Standard 44 for the effective reduction of calcium and magnesium (hardness) along with Barium and Radium 226/228*. Refer to the Specifications, Familiarization, and Warranty sections of this Owner's Guide for more specific product information. To avoid contamination from improper handling and installation, your system should only be installed and serviced by your Culligan Man.

  • Page 13: Performance Data Sheet

    Working Pressure Range: 20-125 psi (140-860 kPa) This Culligan Mark 100 water softener is tested and validated by WQA to ANSI/NSF Standard 44 for the effective reduction of calcium and magnesium (hardness) along with Barium and Radium 226/228*. This softener is efficiency rated, it has a Demand Initiated Regeneration (D.I.R.) feature which complies with specific performance specifi- cations intended to minimize the amount of regenerant brine and water used in their operation.

  • Page 14: Performance Data Sheet

    Working Pressure Range: 20-125 psi (140-860 kPa) This Culligan Mark 100 water softener is tested and validated by WQA to ANSI/NSF Standard 44 for the effective reduction of calcium and magnesium (hardness) along with Barium and Radium 226/228*. This softener is efficiency rated, it has a Demand Initiated Regeneration (D.I.R.) feature which complies with specific performance specifi- cations intended to minimize the amount of regenerant brine and water used in their operation.

  • Page 15: Performance Data Sheet

    Working Pressure Range: 20-125 psi (140-860 kPa) The Culligan Mark 100 water softeners are tested and validated by WQA against ANSI/NSF Standard 44 for the effective reduction of calcium and magnesium (hardness) along with Barium and Radium 226/228*. Refer to the Specifications, Familiarization, and Warranty sections of this Owner's Guide for more specific product information. To avoid contamination from improper handling and installation, your system should only be installed and serviced by your Culligan Man.

  • Page 16: Performance Data Sheet

    Working Pressure Range: 20-125 psi (140-860 kPa) This Culligan Mark 100 water softener is tested and validated by WQA to ANSI/NSF Standard 44 for the effective reduction of calcium and magnesium (hardness) along with Barium and Radium 226/228*. This softener is efficiency rated, it has a Demand Initiated Regeneration (D.I.R.) feature which complies with specific performance specifi- cations intended to minimize the amount of regenerant brine and water used in their operation.

  • Page 17: Performance Data Sheet

    Working Pressure Range: 20-125 psi (140-860 kPa) This Culligan Mark 100 water softener is tested and validated by WQA to ANSI/NSF Standard 44 for the effective reduction of calcium and magnesium (hardness) along with Barium and Radium 226/228*. This softener is efficiency rated, it has a Demand Initiated Regeneration (D.I.R.) feature which complies with specific performance specifi- cations intended to minimize the amount of regenerant brine and water used in their operation.
  • Page 18 MARK SERIES AUTOMATIC WATER CONDITIONERS ® You have just purchased one of the finest water conditioners made. As an expression of our confidence in Culligan products, your water conditioner is warranted to the original end-user, when installed in accordance with Culligan International Company...
  • Page 19 YOU GET YOUR WATER EXPERT, THE CULLIGAN MAN. We’re here to provide you with fast, local, dependable service, making sure any problems you have are taken care of. The Culligan Man has been around for over sixty years, delivery dependable service all along. That’s why people say, “Hey Culligan Man! ”...
  • Page 20 Materials & description: 8-1/2 x 11, 20 page book, saddle stitched, three hole punched - Prints black ink on 50# offset white CHANGE APRVD DATE DCO 200 3/16/00 1/22/01 This page contains materials and DCO information. IT DOES NOT PRINT AS PART OF THE DOCUMENT!