General Information; Introduction; Description; Warranty - Jandy EHE Installation And Operation Manual

Hi-E2
SECTION 1.

General Information

1A. Introduction
This manual contains information for the proper
installation and operation of the Hi-E
pool/spa heater. Certain sections are specifi c to United
States or Canadian installations, and are labeled
United States or Canada. Procedures in this manual
must be followed exactly. To obtain a copy of this
manual contact Jandy Pool Products, Inc. For address
information see back cover.
1B. Description
The Hi-E is a very effi cient gas-fi red pool and
2
spa heater. Its combustion system includes a heat
exchanger which extracts 95% of the energy in the
gas fuel. It has no standing pilot burner. It exceeds the
requirements of energy conservation regulations such
as those in California, Hawaii, New York, Oregon
and other states which require that a pool heater have
intermittent ignition.
The heater is designed to operate in conventional
swimming pool and spa equipment arrangements.
It requires 115V 60 Hz electrical power. It has the
versatile FlexTemp dual-thermostat control system for
pool/spa combinations.
The Hi-E is certifi ed by CSA International to
2
comply with latest editions of applicable standards.
In the United States, the applicable standard is ANSI
Standard Z21.56 for gas-fi red pool heaters. In Canada,
it is Standard CSA 4.7.
The heater has been designed specifi cally to heat
fresh water swimming pools and spas, and with proper
installation and care, it will provide years of reliable
service. Do not use it to maintain pool or spa water
temperature below 70°F. Do not use it as a heating
boiler or general service water heater or to heat salt
water. For special applications, consult your Jandy
dealer.
1C. Warranty
The Hi-E is sold with a limited factory warranty.
2
A copy of the warranty is included in a plastic
bag inside the heater and on the back cover of this
manual. The home owner should fi ll out the warranty
registration card included in the plastic bag and return
it via mail. The warranty does not cover damage
caused by improper installation, operation, or fi eld
modifi cation; or damage to the heat exchanger caused
by corrosive water. See Section 3D for guidelines on
pool water chemistry.
Model EHE
2
SECTION 2.

Installation Instructions

2A. General Requirements
to assure safe and satisfactory operation. The
requirements for pool heaters include the following:
1.
2.
3.
4.
5.
6.
7.
accordance with local codes and the most recent
edition of the National Fuel Gas Code, ANSI Z223.1/
NFPA-54. The Code can be obtained from:
local codes and the most recent edition of the Natural
Gas and Propane Installation Code, CAN/CSA B149.1.
Special Precautions
air. Therefore, a pool heater using LP gas is subject
to special installation rules. Consult local codes and
fi re protection authorities about specifi c installation
restrictions.
to cause cancer or harm the reproductive process.
Follow these installation instructions and applicable
codes exactly to avoid this.
WARNING
Improper installation or servicing can cause prop-
erty damage, injury or death due to fi re, asphyxi-
ation or carbon monoxide poisoning. For indoor
installations, as an additional measure of safety,
Jandy Pool Products, Inc. strongly recommends
installation of suitable Carbon Monoxide detectors
in the vicinity of this appliance and in any adjacent
occupied spaces.
All gas-fi red products require correct installation
Appropriate site location and clearances.
Suf fi cient supply of clean air for combustion and
ventilation.
Proper venting of products of combustion.
Properly sized gas pipe.
Properly sized gas meter.
Adequate water fl ow.
Provision for disposal of combustion condensate
water.
In the United States, installation must be in
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02269
In Canada, install the heater in accordance with
Liquefi ed petroleum (LP) gas is heavier than
Fuel gas and its combustion products are known
Page 1